• Journal of Advanced Marine Engineering and Technology
• /
• 제19권3호
• /
• pp.9-23
• /
• 1995

To analyze the spray and flame in D.I. diesel engine, the visualizing methods by schlieren photograph and diffused background illumination photograph with high speed camera are applied to optically accessible D.I.diesel engine. Wcaporating spray, spray droplets and brightness flame are taken with high speed camera by visuallizing method in accordance with various suction air temperature and injection time. The spray and flame image on the film was analyzed by image analyzer. The optically accessible D.I. diesel engine had the similar pressure characteristic to the real D.I. diesel engine. Experimental results showed that shadow areas of the evaporating spray were extended at higher suction air temperature, spray droplets had a max. Penetration length and their penetrating patterns were dependent on the surrounding gas temperature, and flame size after ignition was largely governed by the evaporated fuel quantity at ignition point and by the surrounding gas condition due to piston motion.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.185-190
• /
• 2001

The cavitation causes suction performance and efficiency of the high-speed pump to be reduced significantly To diminish these effects, the inducer has been used. Most of the inducer is designed at a maximum efficiency point of the pump, therefore suction performance drop due to effects of flow separation and inlet inverse flow is often observed at off-design point. The objective of this study is to find out the cavitation modes at various conditions by applying event detection technique and to design an inducer reducing cavitation. The pressure fluctuations at each cavitating condition were measured at inducer inlet and outlet locations using pressure transducers, which were located 90 degrees apart from each other to identify the cavitation modes. The time-frequency characteristics were analyzed by using Choi-williams distribution. In the second part of this paper, the inducer design method which uses nominal performance characteristic and onset condition of cavitation is introduced and applied to real situation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.385-385
• /
• 2000

In this paper, We presents the development of an automatic fog water collector that operates during fog events. This collector consists of fraction collectors, a wind hall and a fog sensor. If a fog event occurred, then the fog sensor wouldjudge whether it is a fog or not. If the fog sensor judged the fug, then the fog in the air would be rucked by suction fans. At the same time, the wind direction, the wind velocity, the atmospheric temperature and the atmospheric pressure would be measured and recorded. We are also developing a wireless communication system for the remote control and the remote data analysis in order to collect, store and process the data collected in the automatic fog water collector.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.966-972
• /
• 2009

Soil-aggregate system in pavement foundations exist in unsaturated conditions. However, change in water content on foundation layers due to joint and structural cracks during rainfall may cause problems like layer deformations or partial settlements. Therefore, a need exist to evaluate the infiltration and drainage capacity of soil-aggregate foundation system under both saturated and unsaturated conditions. To do that, a laboratory soil-water characteristic curve and permeability under unsaturated conditions are assessed to establish hydraulic properties of geomaterials and limited numerical analysis are performed respectively. As a result, it was found that suction profiles and drainage process was greatly influenced by the initial suction of soil-aggregate system at the time of infiltration, soil water characteristics curves, and hysteresis effects.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.83-90
• /
• 2004

This paper proposes a tool path generation method for machining impellers with 5-axis machining center. The shape of impeller is complex, being composed of pressure surface, suction surface and leading edge, and so on. The compound surface which is made of ruled surface such as pressure surface and suction surface and leading edge such as fillet surface, makes the tool path generation much complicated. To achieve efficient roughing, cutting area is divided into two region and then tool radius of maximum size that do not cause tool intereference is selected for shortening machining time. In finishing, accuracy is improved using side cutting for blade surface and point milling for leading edge.

• 대한간호학회지
• /
• 제44권2호
• /
• pp.149-158
• /
• 2014

Purpose: This study was conducted to compare effects of open and closed suctioning methods on lung dynamics (dynamic compliance, tidal volume, and airway resistance) and hypoxemia (oxygen saturation and heart rate) in mechanically ventilated patients. Methods: This study was a cross-over repeated design. Participants were 21 adult patients being treated with endotracheal intubation using a pressure-controlled ventilator below Fraction of Inspired Oxygen ($FiO_2$) 60% and PEEP $8cmH_2O$. Data were collected at baseline and 1, 2, 3, 4, 5, and 10 minutes after suctioning. Data were analyzed using two-factor ANOVA with repeated measures on time and suctioning type. Results: Effects of the interaction between suction type and time were significant for oxygen saturation and heart rate but not significant for dynamic compliance, tidal volume, or airway resistance. Prior to performance of suctioning, tidal volume and oxygen saturation were significantly lower, but airway pressure and heart rate were significantly higher using the closed suctioning method as compared with the open suctioning method. Conclusion: For patients on ventilator therapy below $FiO_2$ 60% and PEEP $8cmH_2O$, open suctioning performed after delivery of 100% $FiO_2$ using a mechanical ventilator may not have as much negative impact on lung dynamics and hypoxemia as closed suctioning.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.35-36
• /
• 2005

An ejector driven by a liquid is a fluid transfer equipment to be used under a poor suction condition, which means that there exists a possibility to occur a cavitation. It is a highly reliable device because it has no movable part in it, that is only a passive equipment. The ejector is an inevitably necessary one to overcome a poor pumping condition and to mix uniformly two fluids, however it has a low efficiency since it requires a pump for its operation. This study is for the development of a new-type liquid ejector with the application of a nozzle shape alteration, which maximize the suction performance of it. which provides the increased competition with the domestic industries. Also, the increased performance opens a new manufacturing method to use a commercial pipes for the production of an ejector, which is based on a trivial loss of a performance. However, this minor loss can be sufficiently compensated by the increased performance of a new-type ejector. Therefore, the developed ejector by this study can considerably reduce the manufacturing time and cost while its performance is largely increased.

• Archives of Plastic Surgery
• /
• 제38권3호
• /
• pp.241-244
• /
• 2011

Purpose: Seroma formation is still major complication of abdominal donor site after TRAM flap surgery in spite of various efforts to reduce seroma formation such as closed suction drain. We performed a clinical study, that quilting suture at abdominal donor site can prevent seroma formation. Methods: Between May 2002 and September 2008, we performed 600 breast reconstructions using a unilateral TRAM flap except patients who has smoking history or abdominal scar. We performed 300 breast reconstructions without quilting sutures (A: Experimental group) until January 06, and after then 300 reconstructions with quilting sutures (B: Control group). We compared total drain output (mL), time to drain removal (days), and donor site complications between two groups. Results: There were no statistical difference at BMI (p=0.28) and time to remove suction drain between two group. (A: 8.37, B: 9.69) (p=0.40) But, total drain output was reduced with quilting suture. (A: 432.5, B: 495.2) (p=0.005) And also complication rate was decreased, such as seroma formation, epigastric bulging. (A: 1%, B: 7%) (p=0.005) Conclusion: Quilting suture is a simple and reliable method to reduce seroma formation and abdominal donor site complication.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.541-543
• /
• 2011

고령화 사회의 노인성 질환 치료기술에 대한 수요가 증가되고 있는 가운데 최근 한의약이 새롭게 주목을 받고 있다. 본 논문에서는 환자 스스로 의해 기본적인 치료가 이루어질 수 있는 휴대용 한방 멀티 전동 부항 시스템을 제안했다. 본 시스템은 여러 개의 부항컵을 동시에 시술할 수 있고, 타이머와 공압을 자유롭게 조절하여 환부의 장시간 공압 유지로 인한 가려움증 및 근육응결을 해소할 수 있다.

• 한국산학기술학회논문지
• /
• 제8권4호
• /
• pp.874-880
• /
• 2007

CST와 SRF는 슬러지 탈수효율 인자로 가장 널리 사용되고 있다. 이러한 CST와 SRF는 각각의 분석특징의 장.단점으로 인해 실험방법 및 결과 해석시, 슬러지 탈수의 최적조건을 찾아 예측하는데 어려움이 있다. 따라서 본 연구는 탈수성 지표로 이용되는 CST와 SRF의 이론식 가운데 CST와 SRF의 상호관계식을 유도하여 각각의 실측값과 예측값을 비교한 후 비교적 측정이 간편한 CST 시험만으로도 탈수최적조건을 도출할 수 있는 이론식을 검토하였다.