• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2021

Performance of a NACA 63₄-021 hydrofoil in motion under and in close proximity of a free surface for a large range of angles of attack is studied. Lift and drag coefficients of the hydrofoil at different submergence depths are investigated both numerically and experimentally, for 0° ≤ AoA ≤ 30° at a Reynolds number of 10⁵. The results of the numerical study are in good agreement with the experimental results. The agreement confirms the new finding that for a submerged hydrofoil operating at high angles of attack close to a free surface, the interaction between the hydrofoil-motion induced waves on the free surface and the hydrofoil results in mitigation of the flow separation characteristics on the suction side of the foil and delay in stall, and improvement in hydrofoil performance. In comparing with a baseline case, results suggest a 55% increase in maximum lift coefficient and 90% average improvement in performance for, based on the lift-to-drag ratio, but it is also observed significant decrease of lift-to-drag ratio at lower angles of attack. Flow details obtained from combined finite volume and volume of fluid numerical methods provide insight into the underlying enhancement mechanism, involving interaction between the hydrofoil and the free surface.

• Journal of Biosystems Engineering
• /
• v.33 no.6
• /
• pp.384-389
• /
• 2008

Three prototype chestnut harvesters were constructed and evaluated their chestnut collection ability and field efficiency. Air-lock paddle system successfully picked up all loose material, and pick up efficiency was about 56 kg/h. Power required to operate this system was evaluated to be 8.7 kW with an air flow rate of $32.6\;m^3/min$. A radial blade type blower with 0.41 m impeller diameter was considered to be a minimum size for this system. For the auger system, air was sucked into the cylinder as the hinged flat cover began to be opened by the material pushed by the auger, and the empty burrs flew back to the container through the space between auger flights and collected in the bottom of the container. It was considered to add a device to prevent air from flowing back or to use the back flowing air for separation of burrs and nuts inside the container. The venturi system could not pick up chestnuts, as they only carried part way up to the suction hose. Consideration was given to an idea that the venturi could be used as a cleaning and separation mechanism for containers filled with both empty burrs and good nuts. A minimum vacuum of 129 mm wg was required to pick up chestnuts, and the corresponding inlet air velocity was 19.3 m/s. 104 mm of vacuum, which was about 81 % of that required for nuts, was enough to pick up burrs with nuts inside. Also, empty burrs with higher moisture content recorded the same pressure as for the burrs with nuts.

• Wind and Structures
• /
• v.25 no.5
• /
• pp.433-457
• /
• 2017

As a novel typical wind-sensitive structure, the wind load and wind-induced structural behaviors of super-large straight-cone cooling towers are in an urgent need to be addressed and studied. A super large straight-cone steel cooling tower (189 m high, the highest in Asia) that is under construction in Shanxi Power Plant in China was taken as an example, for which four finite element models corresponding to four structural types: the main drum; main drum + stiffening rings; main drum + stiffening rings + auxiliary rings (auxiliary rings are hinged with the main drum and the ground respectively); and main drum + stiffening rings + auxiliary rings (auxiliary rings are fixed onto the main drum and the ground respectively), were established to compare and analyze the dynamic properties and force transferring paths of different models. After that, CFD method was used to conduct numerical simulation of flow field and mean wind load around the cooling tower. Through field measurements and wind tunnel tests at home and abroad, the reliability of using CFD method for numerical simulation was confirmed. On the basis of this, the surface flow and trail characteristics of the tower at different heights were derived and the wind pressure distribution curves for the internal and external surfaces at different heights of the tower were studied. Finally, based on the calculation results of wind-induced responses of the four models, the effects of stiffening rings, auxiliary rings, and different connecting modes on the dynamic properties and wind-induced responses of the tower structure were derived and analyzed; meanwhile, the effect mechanism of internal suction on such kind of cooling tower was discussed. The study results could provide references to the structure selection and wind resistance design of such type of steel cooling towers.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.128-128
• /
• 2017

현재 식물공장에서 사용되고 있는 이식장치는 핀을 이용하여 육묘트레이 위에서 플러그묘를 뽑아 육묘트레이 또는 포트로 옮겨 심는 방식을 채택하고 있다. 이러한 이식 방식은 셀과 셀 사이에 있는 다른 묘의 잎을 파지함으로써 묘를 2개 이상 취출하는 현상이라든지 핀에 의한 잎 손상 등이 우려되고 있어 이에 대한 개선책이 필요하다. 본 연구는 플러그묘의 이식작업 시 잎 손상을 줄이면서 기계 적응성을 향상시킬 수 있는 이식시스템을 개발하기 위해 진공흡인을 이용한 이식 메커니즘에 대해 검토하였다. 플러그묘 이식시스템은 육묘트레이 셀을 X-Y로 옮기는 묘 이송부, 육묘트레이의 셀 하단으로부터 진공을 발생시켜 묘를 떨어뜨리는 진공 흡인부, 낙하되는 묘를 감지하는 센서와 블로워 및 공압 실린더로 구성된 진공 발생부, 혈공된 포트를 진공 발생부의 유도관으로 옮기는 포트 이송부 등으로 설계 제작하였다. 이식 메커니즘은 육묘트레이 하단부로부터 플러그묘를 1개씩 진공흡인하는 방식을 채택하였고, 이를 위해 상하 모두 개방된 72공 육묘트레이($L538{\times}W280{\times}H45mm$)를 윗부분(Ø35mm) 보다 아랫부분(Ø37mm)의 셀이 넓은 형상으로 PP재질의 육묘트레이를 사출금형 제작하였다. 묘 이송부에 장착된 플러그묘는 X축 방향(12개 셀)으로 이식작업이 이루어지고, Y축(6개 셀)으로 이동된 후 다시 동일한 방향으로 연속 작업이 가능하도록 제어프로그램을 구성하였다. 이식 원리는 진공 흡인부에 플러그묘가 이송되면 진공 발생부의 흡착패드가 위로 전진하여 진공을 발생시켜 묘를 흡인하고, 유도관 내에 부착된 광화이버센서에 의해 묘를 감지하여 블로워와 공압실린더를 제어함으로써 이식 공정이 끝나게 된다. 로메인상추의 플러그묘를 대상으로 진공흡인 시험을 실시한 결과 묘 손상없이 이식작업이 가능한 것으로 확인되었다.

• Geotechnical Engineering
• /
• v.14 no.6
• /
• pp.33-44
• /
• 1998

Preliminary study has been conducted to analyse the co-relation between shallow landslides frequently occurring in rainy seasons and the water infiltration into the slope. The change of stress state due to partial saturation of a soil and hence the reduction of its shear strength have been reviewed. The variation of the safety factor of an infinite planar slope in accordance with various water infiltration scenarios has been estimated by limit equilibrium method to explain the mechanism of shallow slope failure. Numerical analysis under the same condition as those of some models dealt with in the previous method has been carried out by using FLAC, a finite difference program, and the results have been compared with the ones obtained by limit equilibrium method. Both results proved to be identical, which implies the ability of the numerical approach to the problems related to the stability analysis of unsaturated slope with the irregular geometry. Further improvement, however, should be made to apply the present analysis procedure to general slopes since it deals with a simple one.

• Archives of Plastic Surgery
• /
• v.43 no.5
• /
• pp.466-469
• /
• 2016

External volume expansion of the recipient site by suction has been proposed as a way of improving fat graft survival. The objective of this study was to present an innovative and simple intraoperative external expansion system to enhance small-volume autologous fat grafting (40-80 mL) and to discuss its background and its mechanism of action. In this system, expansion is performed using a complete vacuum delivery system known as the Kiwi VAC-6000M with a PalmPump (Clinical Innovations). The recipient site is rapidly expanded intraoperatively 10 times for 30 seconds each with a negative pressure of up to 550 mm Hg before autologous fat injection. During this repetitive stimulation, the tissues become grossly expanded, developing macroscopic swelling that regresses slowly over the course of hours following the cessation of the stimulus. The system sets various mechanisms in motion, including scar release, mechanical stimulation, edema, ischemia, and inflammation, which provide an environment conducive for cell proliferation and angiogenesis. In order to maintain the graft construct in its expansive state, all patients are encouraged postoperatively to use the Kiwi three times daily for one minute per session over the course of three days. The handling of this system is simple for both the patients and the surgeon. Satisfactory clinical outcomes have been achieved without significant complications.

• Tribology and Lubricants
• /
• v.30 no.5
• /
• pp.295-302
• /
• 2014

The tribological behavior of an Fe-based bulk amorphous alloy while sliding against a AISI 304 disc is investigated using a unidirectional pin-on-disc type tribometer in dry and distilled water environments. The rod-shaped bulk pins are fabricated by suction casting. The crystallinities of the bulk amorphous alloys before and after the friction tests are determined by X-ray diffraction. The friction coefficient and specific wear rate of the amorphous pin in the water environment are found to be twice and thrice as much as in the dry environment at a low applied pressure, respectively. However, at a higher pressure, the friction coefficient and specific wear rate are 0.4 and 1.02 mg/(Nm/s), respectively, in the water environment. A microstructure analysis shows that the worn surface of the alloy is characterized by delamination from the smooth friction surface, and thus delamination is the main wear mechanism during the friction test in dry sliding environment. In contrast, brittle fracture morphologies are apparent on the friction surface formed in distilled water environment. For the sample tested at a lower sliding speed, the XPS data from the oxide layer are similar to those of the pure element with weak suboxide peaks. For higher sliding speeds, all the main sharp peaks representing the core level binding energies are shifted to the oxide region.

• Nuclear Engineering and Technology
• /
• v.56 no.6
• /
• pp.2029-2038
• /
• 2024

A deep understanding of the characteristics and mechanism of geyser boiling and capillary pumping is necessary to optimize a high-temperature sodium heat pipe. In this work, the Volume of Fluid (VOF) two-phase model and the capillary force model in the mesh wick were used to model the complex phase change and fluid flow in the heat pipe. Computational Fluid Dynamics (CFD) simulations successfully predicted the process of bubble nucleation, growth, aggregation, and detachment from the wall in the liquid pool of the evaporation section of the heat pipe in horizontal and tilted states, as well as the reflux phenomenon of capillary suction within the wick. The accuracy and stability of the capillary force model within the wick were verified. In addition, the causes of geyser boiling in heat pipes were analyzed by extracting the oscillation distribution of heat pipe wall temperature. The results show that adding the capillary force model within the wick structure can reasonably simulate the liquid backflow phenomenon at the condensation; Under the horizontal and inclined operating conditions of the heat pipe, the phenomenon of local dry-out will occur, resulting in a sharp increase in local temperature. The speed of bubble detachment and the timely reflux of liquid sodium (condensate) replenishment in the wick play a vital role in the geyser temperature oscillation of the tube wall. The numerical simulation method and the results of this study are anticipated to provide a good reference for the investigation of geyser boiling in high-temperature heat pipes.

• The Korean Journal of Physiology
• /
• v.18 no.2
• /
• pp.117-124
• /
• 1984

It has been recently reported that cingulate cortex mar facilitate gastric acid secretion, but its facilitatory mechanism on the gastric acid secretion is still unclear. This study was undertaken to investigate the facilitatory mechanism of the cingulate cortex upon gastric acid secretion in rats. Twenty·three male albino rats were divided into the cingulate(N= 13) and the operated control(N= 10) groups. The cingulate group in which cingulate cortex was removed by suction through a slit-shaped opening on each side of, and parallel to, the sagittal suture. In the operated control group, the surgical procedure was ended with the skull opening and the incision of dura mater. The gastric juice was collected via a chronic gastric cannula after 24 hours of fast, with water ad libitum. The juice was collected continuously for 6 hours, starting 3 hours prior to the injection of gastric secretagogue, pentagastrin$(12\;{\mu}g/kg)$ or histamine dihydrochloride $(320\;{\mu}g/kg)$. Three one·hour samples were obtained before ana after the administration of each secretagogue. The two agents were injected separately and subcutaneously at intervals of 1 week, the blood samples were drawn from the abdominal aorta for the radioimmunoassay of postprandial plasma gastrin concentration in response to the forced feeding of 10% cod liver oil. 1) After pentagastrin administration, the volume of gastric juice tended to decrease, but its acidity tended to increase in the cingulate group compared with those of the operated control group. However, there was no any difference in the acid output between the two groups. 2) Histamine-stimulated acid output and volume of the gastric juice of the cingulate group decreased significantly compared with those of the operated control group, while there was not significantly different in the acidity between the two groups. 3) Before pentagastrin or histamine administration, any change was not observed in the gastric acid secretion following the cingulate cortical ablation. 4) Postprandial plasma gastrin concentration in response to the forced feeding of 10% cod liver oil was insignificantly lower in the cingulate group than in the operated control group. It is inferred from the above results that the cingulate cortex exerts a facilitatory influence upon the histamine-stimulated gastric acid secretion in rats, and its influence may not be mediated by the stimulation of gastrin secretion.

• The Korean Journal of Physiology
• /
• v.22 no.2
• /
• pp.189-206
• /
• 1988

The effects of ouabain on the contractile and electrical activities were investigated in the isolated preparations of guinea-pig taenia coli, and compared with those of vanadate. Spontaneous contractions were recorded with force transducer, and electrical activites were measured by use of suction electrode, or single sucrose-gap technique. The contractions were induced by the electrical stimulation for 5 seconds every 1 minute with alternating current (60 Hz, 3.0 V/cm) through the platinum electrodes located in parallel with the long axis of the preparation. All experiments were performed in tris-buffered Tyrode solution which was aerated with $100%{\;}O_2$ and kept at $35^{\circ}C$. The results obtained were as follows: 1) Responses of spontaneous contractions to ouabain were concentration-dependent; $10^{-7}M$ ouabain caused a rise of basal tone. Above the concentration of $10^{-6}M$ ouabain, an initial increase followed by a decrease in tension was observed. 2) A continuous spike discharge was induced by the administration of $10^{-7}M$ ouabain. Above $10^{-6}M$ ouabain, a transient initial increase followed by a decrease in spike frequency and amplitude was produced, and finally membrane potential was sustained at a certain level without a spike discharge. 3) The characteristic response to $10^{-7}M$ ouabain was not blocked by the pretreatment with $10^{-7}M$ atropine. 4) The electrically induced contractions were completely suppressed at the concentration of $2{\times}10^{-7}M$ ouabain. These contractions were blocked more rapidly in paralled with the increase in ouabain concentration. 5) Effects of vanadate on the spontaneous activities were quite different from those of ouabain; $10^{-6}M$ vanadate increased the amplitude of contractions and $10^{-5}M$ vanadate increased slightly both amplitude and frequency of spontaneous contractions. $10^{-4}M$ vanadate showed irregular phasic contractions superimposed on the increased basal tone. 6) $10^{-5}M$ vanadate depolarized the membrane potential and shortened the interval between the bursts of spike discharge, whereas $10^{-4}M$ vanadate induced continuous spike discharge with membrane depolarization. 7) Vanadate caused a characteristic inhibitory response to the contractions induced by electrical stimulation; An initial rapid inhibition of tension development and then gradual recovery to a certain level. From the above results, the following conclusions could be made: 1) The rise of basal tone at $10^{-7}M$ ouabain is due to continuous spike discharge without a silent period. The continuous spike discharge is likely to be associated with a slight membrane depolarization caused by the blockage of Na pump. 2) The biphasic response induced by above $10^{-6}M$ ouabain seems to occur by the different mechanisms. The initial increase in tension is associated with depolarization along with an increase in spike frquency, whereas the subsequent relaxation occurs through a non-electrical mechanism. 3) The characteristic response to $10^{-7}M$ ouabain is resulted not from the action on intrinsic nerve terminal, but from its direct action on the membrane of smooth muscle cells. 4) The phasic contractions superimposed on the increased basal tone at the concentration of $10^{-4}M$ vanadate is resulted from the continuous spike discharge with membrane depolarization, of which mechanism remains unknown. 5) The inhibitory action of ouabain on the electrically induced contractions suggests that the increasein intracellular Na in some way inhibits the electrically induced $Ca^{2+}$ influx. The mechanism of vanadate action on the induced contractions remains unknown.