• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.649-652
• /
• 1999

The (Ba, Sr)TiO$_3$(BST) thin films were fabricated on Pt/Ti/SiO$_2$/Si substrate by RF sputtering technique. The structural properties of the BST thin films were investigated with substrate temperature by XRD, SEM, EDS and AES depth profils. Increasing the substrate temperature, barium multi titanate phases were decreased. The BST thin film had a structure of perovskite type, and had peaks of (100), (200) at the substrate temperature of 50$0^{\circ}C$. When the BST thin films were deposited at the substrate temperature of 50$0^{\circ}C$, the composition ratio of Ba/sr was 52/48.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.545-550
• /
• 2005

We have carried out the fabrications of a barrier layer on a polyethersulfon (PES) film and organic light emitting diode (OLED) based on a plastic substrate by means of atomic layer deposition (ALD). Simultaneous deposition of 30 nm $AlO_x$ film on both sides of the PES film gave a water vapor transition rate (WVTR) of $0.062 g/m^2/day (@38^{\circ}C,\;100%\;R.H.)$. Further, the double layer of 200 nm $SiN_x$ film deposited by plasma enhanced chemical vapor deposition (PECVD) and 20 nm $AlO_x$ film by ALD resulted in a WVTR value lower than the detection limit of MOCON. We have investigated the OLED encapsulation performance of the double layer using the OLED structure of ITO / MTDATA (20 nm) / NPD (40 nm) / AlQ (60 nm) / LiF (1 nm) / Al (75 nm) on a plastic substrate. The preliminary life time to reach 91% of the initial luminance $(1300 cd/m^2)$ was 260 hours for the OLED encapsulated with 100 nm of PECVD-deposited $SiN_x$ and 30 nm of ALD-deposited $AlO_x$.

• Korean Journal of Materials Research
• /
• v.15 no.5
• /
• pp.285-292
• /
• 2005

Anti-reflection film was coated by using spherical silica nano colloids. Silica colloid sol was reserved between two inclined slide glasses by capillary force, and particles were convectively stacked to form a film onto the substrate as the water evaporates. As the sliding speed increased, the thickness of the film decreased and the wavelength at the maximum transmittance decreased. The microstructure observed by SEM showed that silica particles were nearly close packed, which enabled the calculation of the effective refractive index of the film. The film thickness was measured by proffer and calculated from the wavelength of maximum transmittance and the effective refractive index. The effective refractive index of the film could be controlled by a subtle controlling of the coating speed and by mixing two different sized silica particles. When the 100 nm and 50 m particles were mixed at 4:1-5:1 volume ratio, the maximum transmittance of $95.2\%$ for one-sided coating was obtained. This is the one that has increased by $3.8\%$ compared to bare glass substrate, and shows that $99.0\%$ of transmittance or $1.0\%$ of reflectance can be achieved by the simple process if both sides of the substrate are coated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.53-59
• /
• 2003

Using Platinum-silicide (PtSi) formed between silicon substrate and carbon film, we have improved the field emission of electrons from carbon films. Pt films were deposited on n-Si(100) substrates at room temperature by DC sputter technique. After deposition, these PtSi thin films were annealed at 400 ~ $600^{\circ}C$ in a vacuum chamber, and the carbon films were deposited on those Pt/Si substrates by laser ablation at room temperature. The field emission property of C/Pt/Si system is found to be better than that of C/Si system and it is showed that property was improved with increasing annealing temperature. The reasons why the field emission from carbon film was improved can be considered as follows, (1)the resistance of carbon films was decreased due to graphitization, (2)electric field concentration effectively occurred because the surface morphology of carbon film deposited on Pt/si substrates with rough surface, (3)it is showed that annealing induced reaction between Pt film and Si substrate, as a consequence that the interfacial resistance between Pt film and Si substrate was decreased.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1425_1426
• /
• 2009

In this study, commercially available polyethylene terephthalate(PET), which is widely used as a substrate of flexible electronic devices, was modified by dielectric barrier discharge(DBD) method in an air condition at atmospheric pressure, and aluminium - doped zinc oxide (ZnO:Al) transparent conducting film was deposited on PET substrate by r. f. magnetron sputtering method. Surface analysis and characterization of the plasma-treated PET substrate was carried out using contact angle measurements, X-ray Photoelectron Spectroscopy(XPS) and Atomic Force Microscopy (AFM). Especially the effect of surface state of PET substrate on some important properties of ZnO:Al transparent conducting film such as electrical and morphological properties and deposition rate of the film, was studied experimentally. The results showed that the contact angle of water on PET film was reduced significantly from $62^{\circ}$ to $43^{\circ}$ by DBD surface treatment at 20 min. of treatment time. The plasma treatment also improved the deposition rate and electrical properties. The deposition rate was increased almost linearly with surface treatment time. The lowest electrical resistivity as low as $4.97{\times}10^{-3}[\Omega-cm]$ and the highest deposition rate of 234[${\AA}m$/min] were obtained in ZnO:Al film with surface treatment time of 5min. and 20min., respectively.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.116-121
• /
• 1999

0.5 wt%Nb-doped SrTiO3(Nb: STO) thin film was prepared on MgO(100) single crystal substrates by Pulsed Laser Deposition (PLD). The Crystallinity and the orientation of Nb:STO thin films were characterized by XRD with changing the thin film processing condition-oxygen partial pressure, substrate temperature, deposition time and the distance between target and substrate. The orientation of Nb:STO thin film showed (100), (110) and (111) orientations at the substrate temperature of $700^{\circ}C$. The lattice parameter of Nb:STO decreased with increasing Po2 and showed 0.3905 nm at Po2=100 Pa, which was similar to that of the bulk. The thickness of Nb:STO thin film increased with increasing the deposition time and with decreasing the distance between target and substrate.

• Korean Journal of Materials Research
• /
• v.10 no.8
• /
• pp.575-580
• /
• 2000

Diamond thin films were deposited on $Si_3N_4$, SiC, TiC and $Al_2O_3$, substrates by the CVD method using Ta(TaC)Filament, and the appearance of the diamond films and their adhesion properties were examined by SEM, optical microscopy, indentation test and compression topple test. Diamond films were deposited at lower $CH_4$ concentration than 5%$CH_4$ for all kinds of the substrate material, but graphitic(amorphous)carbon was observed at 10%$CH_4$. The diamond film of about $12\mu\textrm{m}$ thickness on WC substrate partly peeled off, but the film on $Si_3N_4$ substrate held good adhesion. The indentation test showed that roughly ground surface was very effective for adhesion of diamond films to substrate. The topple test revealed that film thickness was an important factor governing the adhesion of the diamond film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.7
• /
• pp.600-605
• /
• 2007

Process variables for manufacturing the $CuInSe_2$ thin film were established in order to clarify optimum conditions for growth of the thin film depending upon process conditions (substrate temperature, sputtering pressure, DC/RF Power), and then by changing a number of vapor deposition conditions and Annealing conditions variously, structural and electrical characteristics were measured. Thereby, optimum process variables were derived. For the manufacture of the $CuInSe_2$, Cu, In and Se were vapor-deposited in the named order. Among them, Cu and In were vapor-deposited by using the sputtering method in consideration of their adhesive force to the substrate, and the DC/RF power was controlled so that the composition of Cu and In might be 1 : 1, while the surface temperature having an effect on the quality of the thin film was changed from $100^{\circ}C\;to\;300^{\circ}C$ at intervals of $50^{\circ}C$. The diffract fringe of X-ray, which depended upon the substrate temperature and the Annealing temperature of the manufactured $CuInSe_2$ thin film, was investigated. scanning electron microgaphs of represents a case that a sample manufactured at the substrate temperature of $100^{\circ}C$ was thermally treated at $200{\times}350^{\circ}C$. As a result, at $500^{\circ}C$ of the Annealing temperature, their chemical composition was measured in the proportion of 1 : 1 : 2. It could be known that under this condition, the most excellent thin film was formed, compared with the other conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.96.2-96.2
• /
• 2010

The surface morphology and structural properties of polycrystalline silicon (poly-Si) films made in-situ aluminum induced crystallization at various substrate temperature (300~600) was investigated. Silicon films were deposited by hot-wire chemical vapor deposition (HWCVD), as the catalytic or pyrolytic decomposition of precursor gases SiH4 occurs only on the surface of the heated wire. Aluminum films were deposited by DC magnetron sputtering at room temperature. continuous poly-Si films were achieved at low temperature. from cross-section TEM analyses, It was confirmed that poly-Si above $450^{\circ}C$ was successfully grown on and poly-Si films had (111) preferred orientation. As substrate temperature increases, Si(111)/Si(220) ratio was decreased. The electrical properties of poly-Si film were investigated by Hall effect measurement. Poly-Si film was p-type by Al and resistivity and hall effect mobility was affected by substrate temperature.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.441-447
• /
• 1995

Ba0.65Sr0.35TiO3 (BST) thin films were deposited on Pt/SiO2/Si(100) substrate by rf magnetron sputtering. The substrate temperature changed from 35$0^{\circ}C$ to 55$0^{\circ}C$ and crystalline BST thin films were deposited above 45$0^{\circ}C$. Most of the films had (111) preferred orientation regardless of deposition temperature, but the films changed to (100) preferred orientation as gas pressure increased. The dielectric constant increased with increasing substrate temperature and film thickness, and ranged from 100 to 600 at room temperature. The leakage current increased as substrate temperature increased or as film thickness decreased.