• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.46-54
• /
• 2013

A new terpolymer, styrene-butadiene-benzyl methacrylate copolymer (BzMA-SBR) was synthesized by emulsion polymerization. After polymerization, XSBR ionomer was prepared by deprotection of benzyl group of BzMA through hydrolysis with NaOH. Carboxyl group contents can be controlled by changing the initial feed contents of BzMA. Structure of BzMA-SBR and XSBR were characterized by FTIR, $^1H$ NMR and DSC.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1967-1971
• /
• 2012

A hexavalent chromium (Cr (VI)) is one of the hazardous substances regulated by the RoHS. The determination of Cr (VI) in various polymers and printed circuit board (PCB) has been very important. In this study, the three different analytical methods were investigated for the determination of a hexavalent chromium in Acrylonitrile Butadiene Styrene copolymer (ABS) and PCB. The results by three analytical methods were obtained and compared. An analytical method by UV-Visible spectrometer has been generally used for the determination of Cr (VI) in a sample, but a hexavalent chromium should complex with diphenylcarbazide for the detection in the method. The complexation did make an adverse effect on the quantitative analysis of Cr (VI) in ABS. The analytical method using diphenylcarbazide was also not applicable to printed circuit board (PCB) because PCB contained lots of irons. The irons interfered with the analysis of hexavalent chromium because those also could complex with diphenylcarbazide. In this study, hexavalent chromiums in PCB have been separated by ion chromatography (IC), then directly and selectively detected by inductively coupled plasma atomic emission spectrometry (ICP-AES). The quantity of Cr (VI) in PCB was 0.1 mg/kg.

• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.147-151
• /
• 2014

In many polymer processing operations, the diffusion of small molecules in polymeric materials plays an important role. The fundamental physical property required to design and optimize processing operations is the mutual diffusion coefficient. To investigate the transport properties of polymer/solvent systems at infinite dilution, capillary column inverse gas chromatography (CCIGC) is often employed. In this study, diffusion and partition coefficients of cyclic solvents in styrene/butadiene/styrene (SBS) block copolymer were measured over a wide temperature range using the CCIGC technique.

• Membrane Journal
• /
• v.15 no.1
• /
• pp.62-69
• /
• 2005

SEBS-clay hybrid membranes were prepared by melt intercalation method with internal mixer. In the hybrid, the amount of clay content was fixed to 5 phr. MMT was intercalated or exfoliated by the ionomer and it was confirmed by X-ray diffraction method. D-spacing of the characteristic peak from MMT plate in SAXD was moved and diminished. Gas permeability, mechanical properties and thermal properties of the SEBS-clay hybrid membranes were investigated. Gas permeability through the SEBS-clay hybrid membranes decreased due to increased tortuosity made by intercalation of clay in SEBS.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.281-289
• /
• 1998

Tensile properties including Young's modulus and tear strength were measured for four different rubber compounds; natural rubber(NR), styrene-butadiene copolymer(SBR), ethylene-propylene diene monomer (EPDM), and brominated isobutylene-p-methyl-styrene copolymer(BIMS) as a function of temperature and degree of cure. To see the effect of over cure, a measurement was made of the tensile strength and swelling behavior of the over-cured rubber compounds. Young's modulus, E, was found to have linear dependency on the degree of cure for all rubber compounds. EPDM and BIMS showed the highest and lowest slopes, respectively. The slope of NR and SBR lay between EPDM and BIMS. Tear strength, Gc, decreased in the order of NR>BIMS>SBR>EPDM. As the cure time was extended the degree of cure of NR and SBR decreased, while that of BIMS increased. EPDM showed little change in the degree of cure.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.355-362
• /
• 1998

The purpose of this paper is to develop a rational engineering conductive carbon filled composite through understanding of the effect of conductive carbon black. Polycabonate(PC), Acrylonitrile Butadiene Styrene copolymer(ABS) and PC/ABS resin were used as matrix of the conductive polymer composites. From the experimental results, PC filled with the fiber shaped carbon black showed a possibility to be a rational engineering conductive composite.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.10
• /
• pp.1137-1143
• /
• 2012

Creep characteristic is an important failure mechanism when evaluating engineering materials that are soft material as polymers or used as mechanical elements at high temperatures. One of the popular thermo-plastic polymers, Acrylonitrile Butadiene Styrene (ABS) which is used broadly for machine elements material, as it has excellent mechanical properties such as impact resistance, toughness and stiffness compared to other polymers, was studied for creep characteristic at different levels of stress and temperatures. From the experimental results, the creep limit of ABS at room temperature is 80 % of tensile strength which is higher than PE and lower than PC or PMMA. Also the creep limits decreased to linearly as the temperatures increased, up to $80^{\circ}C$ which is the softening temperature of Butadiene ($82^{\circ}C$). Also the secondary stage of creep among the three creep stages for different levels of stress and temperature was non-existent which occurred for many metals by strain hardening effect.

• Macromolecular Research
• /
• v.16 no.8
• /
• pp.676-681
• /
• 2008

The $\pi$-complex membranes of poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) of two silver salts of $AgBF_4$ and $AgCF_3SO_3$ were prepared and tested for the separation of the propylene/propane mixtures. The Fourier-transform infrared (FT-IR) spectra of these complexes showed that the silver salts were dissolved in SEBS up to a silver mole fraction of 0.14, due to $\pi$-complexation between the aromatic C=C bonds of styrene blocks and silver ions. Above this solubility limit, ion pairs and high-order ionic aggregates began to form, so that silver salts were distributed unselectively in both the EB and PS blocks. The domain size of the PS blocks was enlarged up to this critical concentration with increasing silver concentration without structural transitions, as confirmed by small angle x-ray scattering (SAXS). These structural properties of the SEBS/silver salt complexes may explain the lower separation properties for propylene/propane mixtures compared to poly(styrene-b-butadiene-b-styrene)(SBS)/silver salt complex membranes.

• Elastomers and Composites
• /
• v.54 no.1
• /
• pp.54-60
• /
• 2019

The rapid development of the automobile industry is an important factor that led to the dramatic development of synthetic rubber. The tread part of tire that comes in direct contact with the road surface is related to the service life of the tire. Rubber compounds used in tire treads are often blended with SBR (styrene-butadiene rubber) and BR (butadiene rubber) to satisfy physical property requirements. However, when two or more kinds of rubber are blended, phase separation and silica dispersion problems may occur due to non-uniform mixing of the rubber. Therefore, in this study, we synthesized an SBR copolymer with the same composition as that of a typical SBR/BR blend compound by controlling butadiene content during ESBR (emulsion styrene-butadiene rubber) synthesis. Subsequently, silica filled compounds were manufactured using the synthesized ESBR, and their mechanical properties, dynamic viscoelasticity, and crosslinking density were compared with those of the SBR/BR blended compound. When the content of butadiene was increased in the silica filled compound, the cure rate accelerated due to an increased number of allylic positions, which typically exhibit higher reactivity. However, the T-2 compound with increased butadiene content by synthesis less likely to show an increase in crosslink density due to poor silica dispersion. In addition, the T-3 compound containing high cis BR content showed high crosslink density due to its monosulfide crosslinking structure. Because of the phase separation, SBR/BR blend compounds were easily broken and showed similar $M_{100%}$ and $M_{300%}$ values as those of other compounds despite their high crosslink density. However, the developed blend showed excellent abrasion resistance due to the high cis-1,4 butadiene content and low rolling resistance due to the high crosslink density.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.53-60
• /
• 2002

Polypropylene(PP : continuous phase)/poly (styrene-co-acrylonitrile)(SAN : dispersed phase) blends, and PP/poly(acrylonitrile-butadiene-styrene) (ABS : dispersed phase)blends, containing various amounts of compatibilizer(PP-SAN graft copolymer), were prepared at various shear rates by using twin-screw extruder. In the PP/SAN blend, the average size of the dispersed particles(SAN) was increased with SAN content, while the flexural strength and tensile strength were decreased with SAN content. When the screw rpm was increased from 10 to 60 rpm, the size of the dispersed phase was decreased while the flexural strength and the tensile strength were increased. Maximum mechanical strength and minimum droplet size were observed when the 5 phr compatibilizer was added to the PP/SAN blends. The mechanical strength of PP/ABS blends such as flexural strength and tensile strength increased by adding compatibilizer was reached maximum when blends contained 5 phr compatibilizer.