• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.493-500
• /
• 2008

This paper describes a design of internal frequency modulation(FM) radio antenna fur mobile terminal. In order to control of impedance at an operating frequency of the designed antenna, the lumped constant elements of R and L chip components are used. Patch and stubs located at antenna backside are added to control an exact resonance frequency and miniaturization. A fabricated antenna sire, the measured return loss, impedance, bandwidth, and gain are $40{\times}70{\times}1$ mm, -23 dB at 99 MHz, $55-j7{\Omega}$, 22 MHz($88{\sim}110$ MHz) below -10 dB, and -15 dBi, respectively. These measured results show a good agreement with simulated results. Especially, the measured gain of fabricated antenna is similar with value of a conventional ear-phone antenna in the designed frequency band. The measured radiation pattern agrees well with the calculated omni-directional pattern.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.10
• /
• pp.2269-2274
• /
• 2015

In this paper, the reduced size in horizontal sizes of the narrow band pass filter (BPF) with λg/4 short stub using S shaped folded coupling structure is presented. This BPF with narrow bandwidth show flexible bandwidth with variation of the position of the stubs using the Qe(external quality factor) without changing the impedance value. On the other hand, by replacing the horizontal quarter-wavelength transmission lines with the equivalent S shaped coupled line, the BPF with reduced the size of horizontal can be realized. The proposed BPF shows the insertion loss of 1.46 dB and the return loss of 16.5 dB with bandwidth of 3.4 % at the center frequency of 5.8 GHz, respectively.

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.76-82
• /
• 2011

In this paper, a novel design for a dual-band negative group delay circuit (NGDC) is proposed. Composite right/left-handed (CRLH) ${\lambda}/4$ short stubs are employed as a dual-band resonator. A CRLH ${\lambda}/4$ short stub is composed of a typical transmission line element as the right-handed component and a high-pass lumped element section as the left-handed component. It is possible to simultaneously obtain open impedances at two separate frequencies by the combination of distinctive phase responses of the right/left-handed components. Negative group delay (NGD) can be obtained at two frequencies by using dual-band characteristics of the CRLH stub. In order to achieve a bandwidth extension, the proposed structure consists of a two-stage dual-band NGDC with different center frequencies connected in a cascade. According to the experiment performed, with wide-band code division multiple access (WCDMA) and worldwide interoperability for microwave access (WiMAX), NGDs of $-3.0{\pm}0.4$ ns and $-3.1{\pm}0.5$ ns are obtained at 2.12~2.16 GHz and 3.46~3.54 GHz, respectively.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.2 s.39
• /
• pp.241-241
• /
• 1999

The analysis and design of steel frames are usually carried out under the assumption that the connections of beam-to-column are either fully rigid or ideally pinned. However the connections actually show semi-rigid behavior in many cases. The authors investigated the structural behavior of simi-rigid connection with reformed T-stub by using of SM490 steel. The objective of the study is to investigate the structural behavior of the beam-to-column semi-rigid connection with reformed T-stub, which is made of SS400 steel. The beam-to-column connections by using reformed T-stubs were tested under monotonic loading and cyclic loading condition. The possibility of application of semi-rigid connections with reformed T-stubs was ascertained from test results.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.142-145
• /
• 2015

In this work, open stubs were fabricated on a polyether sulfone (PES) substrate, and their basic radio frequency (RF) characteristics were investigated for application to RF matching components of a flexible monolithic microwave integrated circuit (MMIC). According to the results, an open stub employing coplanar waveguide (OSCPW) on PES exhibited much lower loss than that on silicon substrate. The OSCPW with a length of $500{\mu}m$ on PES showed capacitance values of 0.031 ~ 0.044 pF from 0.5 to 50 GHz. For application to a relatively high-value capacitive matching, an open stub employing a fishbone-type transmission line (OSFTTL) was fabricated on PES, and its characteristics were investigated. The OSFTTL showed much higher capacitance values than the OSCPW due to the high effective permittivity value. Specifically, the OSFTTL on PES showed capacitance values of 0.066 ~ 0.24 pF from 0.5 to 50 GHz, which are higher than those for the open stub on silicon substrate. The above results indicate that the OSCPW and OSFTTL on PES can be effectively used for application to low/high-value capacitive matching components on microwave and millimeter wave flexible MMIC. To the best of the authors' knowledge, this work is the first report of the investigation of RF capacitive matching components on PES substrate.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.1-8
• /
• 2011

In this paper, a microstrip bandpass filter(BPF) with 3 dB bandwidth of more than 50 % at center frequency of 30 GHz was implemented. The implemented BPF is to be used as ASK(Amplitude Shift Keying) transmission and reception filters in IF band for THz transmitter and receiver capable of 10 Gb/s wireless data transmission. The microstrip BPF with ultra-wideband characteristics was implemented using a stepped-impedance lowpass filter(LPF) and a composite quarter-wave short stubs where the LPF is functioning as attenuating the upper stopband and quarter-wave short stubs is functioning as attenuating the lower stopband. The measured results are as follows; the insertion loss is 0.65 dB at 30 GHz, the stopband characteristics are -10 dB and -16 dB at 10 GHz and 50 GHz, respectively, and the passband flatness is ${\pm}0.5$ dB at 20~40 GHz.

• Journal of Advanced Navigation Technology
• /
• v.27 no.1
• /
• pp.57-62
• /
• 2023

This paper proposes a tri-band bandpass filter using dual-mode stepped-impedance resonators (SIRs) with parallel coupled structures. The proposed filter adopts U-shaped SIRs with open stubs and parallel coupled lines (PCLs) that have inter-digital and comb-line shorted ends. Two U-shaped SIRs with open stubs build the first and third passband, and the central PCL resonators build the second passband. Five resonators and coupling structures are theoretically analyzed to derive the scattering parameters of the proposed filter. A novel tri-band bandpass filter is designed and fabricated using the induced scattering parameters. The measured result of the fabricated tri-band bandpass filter shows a good agreement with the simulated one.

• Structural Engineering and Mechanics
• /
• v.12 no.2
• /
• pp.157-168
• /
• 2001

In this paper, experimental investigation into the behavior of reinforced concrete (RC) columns tested under large lateral displacement with four different types of loading arrangements is presented. Each loading arrangement has a different system for controlling the consistency of the loading condition. One of the loading arrangements used three units of link mechanism to control the parallelism of the top and bottom stub of column during testing, and the remaining employed eight hydraulic jacks for the same purpose. The loading systems condition used in this investigation were similar to the actual case in a moment-resisting frame where the tested column was displaced in a double curvature. Ten model column specimens, divided into four series were prepared. Two columns were tested monotonically until collapse, and unless failure took place at an earlier stage of loading, the remaining eight columns were tested under cyclic loading. Test results indicated that the proposed system to keep the top and bottom stubs parallel during testing performed well.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.538-541
• /
• 2013

A compact microstrip lowpass filter (LPF) with an elliptic function response is proposed. A high equivalent capacitance and inductance between the structures of the resonator result in the sharp transition band of 0.04 GHz from 4 GHz to 4.04 GHz with an attenuation level of -3 dB and -20 dB, respectively. To improve the LPF rejection band, multiple open stubs are connected to the proposed resonator. A filter with a 3-dB cut-off frequency at 4 GHz is designed, fabricated, and measured, and agreement between the measured and simulated results is achieved. The results show that a stopband bandwidth of 131% with a suppression level better than -20 dB is obtained while achieving a compact size with a wide stopband.

• Journal of electromagnetic engineering and science
• /
• v.7 no.1
• /
• pp.42-46
• /
• 2007

This paper presents a linear amplitude equalizer developed to secure the linearity of the slope of the amplitude over the frequency band ranging $2\sim18\;GHz$. The circuit model is featured by the resistor placed between each pair of a transmission-line and a stub. The design includes finding the values of resistors and stubs to have the optimal linear slope and return loss performances. The measured data show the acceptable performances of the slope variation and return loss over $2\sim18\;GHz$.