• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.821-826
• /
• 2001

This paper presents four types of strut-tie model design approaches of structural concrete through the anchorage zone design of a post-tensioned concrete I-beam. The differences and distinctive feature of each approach in terms of structural type of selected strut-tie model, external force acting on strut-tie model, effective strength of concrete strut, and strut-tie model design procedure are analyzed and compared. The outcomes of present study enable structural designers to understand the merits and demerits of each strut-tie model design approach, and thus to conduct reasonable and accurate design of structural concrete.

• 한국공간구조학회논문집
• /
• 제19권2호
• /
• pp.27-34
• /
• 2019

This study proposes a technique to dissipate the energy of a rocking wall installed on a frame by using a metallic damper. The rocking behavior is to turn left and right about the wall vertical axis. The development system is a method of dissipating energy by installing a damper which is the like on a large displacement portion. Experimental results showed that in case of shorter strut make strength capacity increasement and in case of longer strut make deformation capacity increasement. The higher the strut height, the better the energy dissipation capacity. The proposed equation for estimating the steel damper strength applied to this study is a straight type strut damper. However, it is not suitable for calculation of the strength of clamped type strut damper where both flexural behavior and shear behavior are mixed.

• 항공우주기술
• /
• 제3권2호
• /
• pp.191-196
• /
• 2004

현재까지의 착륙장치의 연구동향은 대부분이 공기-유압식 완충기의 충격흡수 성능해석에 집중되어 있으며 이러한 연구내용을 판스프링식 복합재료 착륙장치의 해석에 적용하기에는 많은 문제점이 있는 실정이다. 공기-유압식 완충기의 충격흡수 특성은 착륙장치 구조물의 유연성보다 내부 구조의 설계 방식에 따라 영향을 받으나, 판스프링식 복합재료 착륙장치는 재료 자체가 지니는 탄성거동과 감쇠특성으로 충격흡수 역할을 수행한다. 따라서 구조물을 구성하는 재료의 선정 및 형상이 매우 중요하다. 본 연구에서는 실제 착륙장치의 충격 낙하 상태를 정확히 모사 할 수 있는 시험치구를 이용하여 현재 개발 중에 있는 고정식(fixed)복합재료 착륙장치가 갖고 있는 충격흡수특성, 탄성거동 및 감속특성 등을 파악하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1496-1503
• /
• 2005

The study on the lateral earth pressure is briskly preformed for various conditions such as type of retaining walls, ground condition, and type of supporting systems. It is not simple to determine the distribution of lateral earth pressure accurately, however, because the lateral earth pressure is affected by various factors. This study is performed to analyze the behavior of earth retaining walls for new excavation contacting with existing excavation by comparing with the site measuring values before and after new excavation. On the base of observation, the distribution of strut axial forces is similar to that of ganeral earth retaining walls, but strut axial forces is increased by removal of existing earth anchors. When new excavation is performed contacting with existing excavation, the axial force of strut is decreased because of soil exclusion in the behind walls, but that force is increased after new exeavation. The analysis result show that the installation of strut in middle part makes a effect to not only 1 adjacent strut, but 3-5 adjacent struts. Also during new excavation strut axial forces is decreased by relaxation of total earth retaining wall system.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권4호
• /
• pp.45-52
• /
• 2019

본 연구에서는 벽체의 록킹 거동을 고려한 내진보강 기법을 개발하였다. 록킹 거동은 벽체 수직 축을 중심으로 좌우로 회전하는 것으로, 개발 시스템은 변위 큰 부분에 댐퍼 등을 설치하여 에너지를 소산 시키는 방법이다. 댐퍼는 강재댐퍼를 사용하였으며, 스트럿 형상 및 높이를 변수로 선정하였다. 실험결과 스트럿 높이가 짧을수록 강도 능력이, 길수록 변형능력이 우수한 것으로 평가되었다. I형과 S형 스트럿 능력을 평가한 결과, S형이 우수한 내진 성능을 보유한 것으로 평가되었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.617-622
• /
• 2000

In this study, effective compressive strength and nodal zone of Strut-and-Tie Model are studied to propose a new design method for RC T-type pier coping for prevention of sudden brittle failure. The coping which transmits loads of bridge to pier should be properly designed to retain ductile behavior. In order to carry out this proper design using STM, tie must yield before concrete fails, and a stress at strut should not exceed a certain effective stress. Therefore, reasonable determination of the effective compressive strength of strut by considering stress states at the nodal zone exactly is very important. Since conventional STM is applied under assumption that all nodes are under hydrostatic stress state, actual non-hydrostatic stress state in nodal zone caused by geometrical characteristics, loading conditions, support conditions of structures can not be considered properly. In order to apply STM for design of RC T-type pier coping, the non-hydrostatic stress state of nodal zone is considered and effective compressive strength is proposed. Then, a new design method of RC T-type pier coping which applies the principle of superposition to obtain optimum ductile behavior is rationally designed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.179-182
• /
• 2005

Recently, many design codes including ACI 318-02 recommend the use of a strut-tie model approach for design of structural concrete with D-region(s). However, there are several unclear problems and shortcomings in the codes' strut-tie model approach. A grid strut-tie model approach was proposed to resolve these problems. In this study, the ultimate strengths of 17 deep beams, the most familiar type of D-regions, were evaluated for the validity check of the grid strut-tie model approach. The analytical results obtained by the approach are compared with those by the strut-tie model approach presented by CEB-FIP, AASHTO LRFD, and ACI 318-02.

• 한국공간구조학회논문집
• /
• 제20권4호
• /
• pp.45-52
• /
• 2020

In this study, performance experiments were performed on the shape of steel dampers that affect the rocking behavior. Three types of strut shapes of SI type, SV type and SS type were considered as experimental variables. As a result of the experiment, the capacity to resist the moment and drift ratio according to the strut shape of the steel damper was evaluated as very close. Finally, it was evaluated that the SV type steel damper has stable deformation and energy dissipation capability. As a result of the evaluation of the proposed damper transmission force, it is considered that the damper transmission force is evaluated larger than the applied horizontal force, and it is necessary to supplement it.

• 대한조선학회논문집
• /
• 제41권6호
• /
• pp.114-119
• /
• 2004

For passenger vessels, twin shaft types in propulsion system is generally adopted to provide a high-speed performance in low draught due to restricted operating condition in harbors or water channels. Struts of twin open shaft type support the shafts, bearings, and propellers. Therefore, strut design is needed to consider not only hydrodynamic performance but also structural and noise/vibration performance, In this paper, considerations in strut design at the initial design stage have been discussed based on existing references, numerical calculations, and their comparisons. Also, the strut design of a RoPax ferry has been carried out at the initial design stage, for an example.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.845-850
• /
• 2000

This paper presents the results of tests performed on the transfer girders which have been generally used between upper walls and lower frames in the hybrid structures. The 8 specimens were designed using (1) ACI method, (2) strut-tie model, and (3) X-type shear reinforcement cage. The capacities of the specimens are in general larger than the design values except the one designed according to strut-tie model. The reason for this difference seems to be due to the arbitrary allocation of transferred shear force to the path of direct compression strut and the path of indirect strut and tie. The failure modes turn out toe be (1) shear failure at critical shear zone, (2) compressive concrete crushing in the diagonal strut in the shear zone of transfer girder, and (3) compressive concrete crushing in the corner of upper wall.