• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.188.1-188.1
• /
• 2015

For present investigation Fe/MgO/Fe/Co multilayer stack is grown on Si substrate using e-beam evaporation in ultrahigh vacuum. This stack is irradiated perpendicularly by 120 MeV $Ag^{8+}$ at different fluences ranging from $1{\times}10^{11}$ to $1{\times}10^{13}ions/cm^2$ in high vacuum using 15UD Pelletron Accelerator at Inter University Accelerator Centre, New Delhi. Magnetic measurements carried out on pre and post irradiated stacks show significant changes in the shape of perpendicular hysteresis which is relevant with previous observation of re-orientation of magnetic moment along the direction of ion trajectory. However increase in plane squareness may be due to the modification of interface structure of stacks. X-ray reflectivity measurements show onset of interface roughness and interface mixing. X-ray diffraction measurements carried out using synchrotron radiation shows amorphous nature of MgO and Co layer in the stack. Peak corresponding body centered Fe [JCPDS-06-0696] is observed in X-ray diffraction pattern of pre and post irradiated stacks. Peak broadening shows granular nature of Fe layer. Estimated crystallite size is $22{\pm}1nm$ for pre-irradiated stack. Crystallite size first increases with irradiation then decreases. Structural quality of these stacks was further studied using transmission electron microscopic measurements. Thickness from these measurements are 54, 36, 23, 58 and 3 nm respectively for MgO, Fe, MgO, Fe+Co and Au layers in the stack. These measurements envisage poor crystallinity of different layers. Interfaces are not clear which indicate mixing at interface. With increase fluence mixing and diffusion was increased in the stack. X-ray absorption spectroscopic measurements carried out on these stacks show changes of Fe valence state after irradiation along with change of O(2p)-metal (3d) hybridized state. Valence state change predicts oxide formation at interface which causes enhanced in-plane magnetization.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.6
• /
• pp.751-763
• /
• 2005

Statement of problem. To improve a direct implant fixation to the bone, various strategies have been developed focusing on the surface of materials. The surface quality of the implant depends on the chemical, physical, mechanical and topographical properties of the surface. The different properties will interact with each other and a change in thickness of the oxide layer may also result in a change in surface energy, the surface topography and surface, chemical composition. However, there is limited the comprehensive study with regard to changed surface and biologic behavior of osteoblast by anodization. Purpose of study. The aim of this study was to analyze the characteristics of an oxide layer formed and to evaluate the cellular biologic behaviors on titanium by anodic oxidation (anodization) by cellular proliferation, differentiation, ECM formation and gene expression. And the phospholipase activity was measured on the anodized surface as preliminary study to understand how surface properties of Ti implant are transduced into downstream cellular events. Methods and Materials. The surface of a commercially pure titanium(Grade 2) was modified by anodic oxidation. The group 1 samples had a machined surface and other three experimental specimens were anodized under a constant voltage of 270 V(Group 2), 350 V(Group 3), and 450 V(Group 4). The specimen characteristics were inspected using the following five categories; the surface morphology, the surface roughness, the thickness of oxide layer, the crystallinity, and the chemical composition of the oxide layer. Cell numbers were taken as a marker for cell proliferation. While the expression of alkaline phosphatase and Runx2 (Cbfa1) was used as early differentiation marker for osteoblast. The type I collagen production was determined, which constitutes the main structural protein of the extracellular matrix. Phospholipase $A_2$ and D activity were detected. Results. (1) The anodized titanium had a porous oxide layer, and there was increase in both the size and number of pores with increasing anodizing voltage. (2) With increasing voltage, the surface roughness and thickness of the oxide film increased significantly (p<0.01), the $TiO_2$phase changed from anatase to rutile. During the anodic oxidization, Ca and P ions were more incorporated into the oxide layer. (3) The in vitro cell responses of the specimen were also dependant on the oxidation conditions. With increasing voltage, the ALP activity, type I collagen production, and Cbfa 1 gene expression increased significantly (p<0.01), while the cell proliferation decreased. (4) In preliminary study on the relation of surface property and phospholipase, PLD activity was increased but $PLA_2$ activity did not changed according to applied voltage. Conclusion. The anodized titanium shows improved surface characteristics than the machined titanium. The surface properties acquired by anodization appear to give rise more mature osteoblast characteristics and might result in increased bone growth, and contribute to the achievement of a tight fixation. The precise mechanism of surface property signaling is not known, may be related to phospholipase D.

• Applied Microscopy
• /
• v.39 no.2
• /
• pp.141-147
• /
• 2009

The antennae of millipedes have a prominent function in detecting various types of environmental stimuli, and structural modification of the antennae is closely associated with the degree of sense recognition. Although the biological significance of the antennal sensillae to millipedes are widely understood, the structure and function of the antennal sensillae are still not clear and more precise analysis is required. We have analysed the ultrastructural characteristics of the antennal sensillae in a millipede Anaulaciulus koreanus koreanus using field emission scanning electron microscopy (FESEM). According to their morphological and substructural features, we could identify three different types of antennal sensillae as follows: trichoid sensilla (TS), chaetiform sensilla (CS) and basiconic sensilla (BS). The TS on the articles are long, blunt-tipped, almost straight hairs with deep longitudinal grooves in their lower parts whereas, the CS are long, sickleshaped bristles with longitudinal grooves acuminating toward the tip. The BS can be subdivided further into three subtypes which are the large-sized basiconic sensilla ($BS_1$), the small-sized basiconic sensillae ($BS_2$) and the spiniform basiconic sensillae ($BS_3$). The BS between the terminal segment and distal margins of the other segments are clearly discriminated in this species.

• Journal of Korea Water Resources Association
• /
• v.42 no.6
• /
• pp.505-511
• /
• 2009

When replacing deteriorated pipes, it is important to select pipe diameters of new pipes for improving the long-term reliability of a water distribution system. However, as the use of larger diameter pipes brings cost increase, it is required to evaluate the improvement of the reliability by the use of larger diameter pipes. In this study, we propose a methodology to evaluate the improvement of the reliability by the use of different pipe diameters. For this purpose, we rely on the segment-based minimum cutset method with the success mode approach to evaluate the reliability of a water distribution system and determine which pipes and their diameters will be replaced to improve the reliability using GA, After the suggested method is applied to a real water distribution system, the optimized pipe diameters produces higher reliability of the system than the current ones with the same construction cost. However, compared to the increase rate of the construction cost, the improvement of the reliability is not significant. Thus, in addition to the use the different pipe diameters, the structural modification or adding new valves to the system is necessary to improve the reliability efficiently.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.611-620
• /
• 2016

In the construction of nuclear power plants, only 420 MPa reinforcing bars are allowed and, therefore, so many large-diameter bars are placed, which results in steel congestion. Consequently, re-bar works are difficult and the quality of RC structures may be deteriorated. To solve the steel congestion, 550 MPa bars are necessary. Among many items for verifying structural performance of reinforced concrete with 550 MPa bars, the 43 mm hooked bars are examined in this study. All specimens failed by side-face blowout and the side cover explosively spalled at maximum loads. The bar force was initially transferred to the concrete primarily by bond along a straight portion. At the one third of maximum load, the bond reached a peak capacity and began to decline, while the hook bearing component rose rapidly. At failure, most load was resisted by the hook bearing. For confined specimens with hoops, the average value of test-to-prediction ratios by KCI code is 1.45. The modification factor of confining reinforcement which was not allowed for larger than 35 mm bars can be applied to 43 mm hooked bars. For specimens with 70 MPa concrete, the average value of test-to-prediction ratios by KCI code is 1.0 which is less than the values of the other specimens. The effects of concrete compressive strength should be reduced. An equation to predict anchorage capacity of hooked bars was developed from regression analysis including the effects of compressive strength of concrete, embedment length, side cover thickness, and transverse reinforcement index.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.312-317
• /
• 2015

Seafarers can confront to evacuate from the ship with many reasons such as collision, grounding and fire accident. It believes that evacuation time from ship is very important element in order to increase survival rate in the contingency circumstance, however narrow and complex structure of ship is one of obstacle element against prompt evacuation. Taking into consideration the unique structure of ship compared to the structure of other facilities, speed of fire propagation on board ship is faster than the same size of other type facilities. Therefore, measures to prompt evacuation are required. But it comes with the behavioral constraints of the crews and passengers of the nature of operating in a complex structure with narrow vessels. Therefore, in this study, we propose a formula to be analyzed by theoretical approach and simulation methods to improve the survival rate for the crew and passenger of the ship through the ship's structural modification. We analyzed the temperature rise and visibility which are the most influential effects on the life safety in the event of fire by using a three-dimensional analysis of sight-only program Fire Dynamic Simulator (FDS) as analytical tools.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.4
• /
• pp.730-738
• /
• 2016

est19 is a gene from Bacillus sp. K91 that encodes a new esterase. A comparison of the amino acid sequence showed that Est19 has typical Ser-Gly-Asn-His (SGNH) family motifs and could be grouped into the SGNH hydrolase family. The Est19 protein was functionally cloned, and expressed and purified from Escherichia coli BL21(DE3). The enzyme activity was optimal at 60℃ and pH 9.0, and displayed esterase activity towards esters with short-chain acyl esters (C₂-C₆). A structural model of Est19 was constructed using phospholipase A1 from Streptomyces albidoflavus NA297 as a template. The structure showed an α/β-hydrolase fold and indicated the presence of the typical catalytic triad Ser49-Asp227-His230, which were further investigated by site-directed mutagenesis. To the best of our knowledge, Est19 is a new member of the SGNH hydrolase family identified from thermophiles, which may be applicable in the industrial production of semisynthetic β-lactam antibiotics after modification.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.36 no.1
• /
• pp.15-24
• /
• 2018

N-glycosylation is an important posttranslational modification that results in a variety of biological activities, structural stability, and protein-protein interactions. There are still many mysteries in the structure and function of N-glycans, and detailed elucidation is necessary. Baculovirus expression system (BES) is widely used to produce recombinant glycoproteins, but it is not suitable for clinical use due to differences in N-glycan structure between insects and mammals. It is necessary to develop adequate model glycoproteins for analysis to efficiently alter the insect-type N-glycosylation pathway to human type. The previous research shows the recombinant alpha 1-acid glycoprotein (${\alpha}1AGP$) secreted from silkworm cultured cells or larvae is highly glycosylated and expected to be an excellent research candidate for the glycoprotein analysis expressed by BES. Therefore, we improved the ${\alpha}1AGP$ to be a better model for studying glycosylation. The modified ${\alpha}1AGP$ (${\alpha}1AGP{\Delta}$) recombinant protein was successfully expressed and purified by using BES, however, the expression level in silkworm cultured cells and larvae were lower than that of the ${\alpha}1AGP$. Subsequently, we confirmed the detailed profile of N-glycan on the ${\alpha}1AGP{\Delta}$ by LS/MS analysis the N-glycan structure at each glycosylation site. These results indicated that the recombinant ${\alpha}1AGP{\Delta}$ could be usable as a better model glycoprotein of N-glycosylation research in BES.

• Korean Journal of Materials Research
• /
• v.14 no.10
• /
• pp.731-736
• /
• 2004

Herein, we report on the co-firing of a low-K wiring substrate and a middle-K functional substrate in LTCC. Firstly, we researched the sintering behavior and dielectric properties of the low-k wiring substrate comprised by alumina and glass frit with ${\varepsilon}_r$, of $\sim7$ and the middle-k functional substrate comprised by $Ba_{5}Nb_{4}O_{15}$ and glass frit with ${\varepsilon}_r$, of $20\sim30$. The warpage and delamination between the hetero layers of the low-K and the middle-K composition were also studied. In particular, physical matching of the hetero layers could be possible by adjusting of the sintering properties of the composition. We observed that an introduction of the glass frit to the low- and middle-K substrate gives rise to a minimization of an effect given by separation of the hetero layers, and modification of the fraction of the glass frit accompanied by a variation of the composition could control the sintering behavior and its beginning temperature. In the case of co-firing of the L03 as the low-K wiring substrate composition and the M03 as the middle-K functional substrate composition at $875^{\circ}C$, we could fabricate a desirable structure of hetero layers without any kinds of structural defects such as separation, warpage, delamination, pore trap, etc. We suppose that the co-firing techniques described in this study would provide a helpful method to fabricate a LTCC multi-functional for the next generation.

• Korean Journal of Microbiology
• /
• v.48 no.2
• /
• pp.79-86
• /
• 2012

ErmSF is one of the Erm family proteins which catalyze S-adenosyl-$_L$-methionine dependent modification of a specific adenine residue (A2058, E. coli numbering) in bacterial 23S rRNA, thereby conferring resistance to clinically important macrolide, lincosamide and streptogramin B ($MLS_B$) antibiotics. $^{222}FXPXPXVXS^{230}$ (ErmSF numbering) sequence appears to be a consensus sequence among the Erm family. This sequence was supposed to be involved in direct interaction with the target adenine from the structural studies of Erm protein ErmC'. But in DNA methyltarnsferase M. Taq I, this interaction have been identified biochemically and from the complex structure with substrate. Arginine 223 and 227 in this sequence are not conserved among Erm proteins, but because of the basic nature of residues, it was expected to interact with RNA substrates. Two amino acid residues were replaced with Ala by site-directed mutagenesis. Two mutant proteins still maintained its activity in vivo and resistant to the antibiotic erythromycin. Compared to the wild-type ErmSF, R223A and R227A proteins retained about 50% and 88% of activity in vitro, respectively. Even though those arginine residues are not essential in the catalytic step, with their positive charge they may play an important role for RNA binding.