• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.310-315
• /
• 2011

General portal machine represents a distinct weak spot concerning their structural behavior because of long protruding structure components, such as saddles and rams. The weak point causes the deformation of the machine tool and consequently rises a severe machining error. The purpose of this study is to improve the structural design of crossrail in order to minimize it's distortion. Tool Center Point (TCP) was chosen as a reference point for evaluating the distortion effect of a crossrail and topological optimization was adopted as a method of structural design improvement. The displacements of TCP according to the machining positions were investigated by structural analyses for both of original crossrail design and the improved one. The comparing results showed that the displacement of TCP could be reduced about 55% maximum.

• Computers and Concrete
• /
• v.18 no.5
• /
• pp.983-998
• /
• 2016

Structural optimization is one of the most important topics in structural engineering and has a wide range of applicability. Therefore, the main objective of the present study is to apply the Lagrange Multiplier Method (LMM) for minimum cost design of singly and doubly reinforced rectangular concrete beams. Concrete and steel material costs are used as objective cost function to be minimized in this study, and ultimate flexural strength of the beam is considered to be as the main constraint. The ultimate limit state method with partial material strength factors and equivalent concrete stress block is used to derive general relations for flexural strength of RC beam and empirical coefficients are taken from topic 9 of the Iranian National Building Regulation (INBR9). Optimum designs are obtained by using the LMM and are presented in closed form solutions. Graphical representation of solutions are presented and it is shown that proposed design curves can be used for minimum cost design of the beams without prior knowledge of optimization and without the need for iterative trials. The applicability of the proposed relations and curves are demonstrated through two real life examples of SRB and DRB design situations and it is shown that the minimum cost design is actually reached using proposed method.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.2
• /
• pp.63-72
• /
• 1990

In this study, an optimization design of reinforced concrete structures is performed by using the structural optimization techniques based on the LRFD criteria. The target reliability index is estimated by the optimal reliability index considering the expected cost which is taken as a sum of the structural cost and the expected costs due to failure of the structure. The load and resistance factors calculated by using level I reliability theory with the target reliability index are compared for each load combination (D+L, D+L+w). The results of this study show that the resistance factors are ${\phi}_{M}$=0.90, ${\phi}_{V}$==0.70, ${\phi}_{C}$==0.65 and the load factors are 1.20D + 1.70L, 1.07L + 0.07L + 1.10W. The optimization techinques used to this study are S.L.P. The optimization design based on the LRFD criteria is more economical and rational than other criteria.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.238-246
• /
• 2000

In this paper, an optimization method of thin walled beam structures is proposed, Stiffnesses of a thin walled beam are characterized by the thickness of thin plates and the shape of the typical section of the beam. Explicit formula for section properties such as area, area moment of inertia, and torsional constants are derived using the response surface method. The explicit formula can be used for the optimal design of a structural system which consists of complicated thin walled beams. A vehicle structural system is optimized to demonstrate the proposed method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.836-840
• /
• 2006

Design optimization of layered plates bonding process is conducted to achieve high product quality by considering uncertainties in a manufacturing process. During the cooling process of the sequential sub-processes, different thermal expansion coefficients lead to residual stress and displacement. thus resulting in defects on the surface of the adherent. So robust process optimization is performed to minimize the residual stress mean and variation of the assembly while constraining the distortion as well as the instantaneous maximum stress to the allowable limits. In robust process optimization, the dimension reduction (DR) method is employed to quantify both reliability and quality of the layered plate bonding. Using this method. the average and standard deviation is estimated. Response surface is constructed using the statistical data obtained by the DRM for robust objectives and constraints. from which the optimum solution is obtained.

• Advances in Computational Design
• /
• v.1 no.2
• /
• pp.119-138
• /
• 2016

In this article, hybridization of enhanced colliding bodies optimization (ECBO) with upper bound strategy (UBS) that is called UECBO is proposed for optimum design of truss structures with frequency constraints. The distinct feature of the proposed algorithm is that it requires less computational time while preserving the good accuracy of the ECBO. Four truss structures with frequency limitations selected from the literature are studied to verify the viability of the algorithm. This type of problems is highly non-linear and non-convex. The numerical results show the successful performance of the UECBO algorithm in comparison to the CBO, ECBO and some other metaheuristic optimization methods.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.451-458
• /
• 2014

This study is a practical research for setting a process of making references of design decision and guidlines of limitation in the movement from the design development to the construction design by StrAuto. StrAuto, as a parametric modeling and optimization tool for building structure, enables a quantity of design cases to be analyzed automatically by changing parameters of sturctural properties. So the designer using StrAuto can check a lot of analysis data crossing thousands of cases, see which case is out of acceptable range, and make a decision for design and optimization. In this thesis, the application of StrAuto optimization process to the residence tower UIC project shows the practical applicability in the construction design and value engineering. StrAuto optimized ideally volume of core walls by 31.3% and lead the final revised model applied to the construction design to reduce volume by 18.1%. The significance of this research is the implementation of process that the designer can quickly review a number of cases and get a direction for construction design and optimization after design development.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.407-417
• /
• 2003

Enen though several GA-based optimization algorithms have been successfully applied to complex optimization problems in various engineering fields, GA-based optimization methods are computationally too expensive for practical use in the field of structural optimization, particularly for large- scale problems. Furthermore, a successful implementation of GA-based optimization algorithm requires a cumbersome and trial-and-error routine related to setting of parameters dependent on a optimization problem. Therefore, to overcome these disadvantages, a high-performance GA is developed in the form of distributed hybrid genetic algorithm for structural optimization on a cluster of personal computers. The distributed hybrid genetic algorithm proposed in this paper consist of a simple GA running on a master computer and multiple μ-GAs running on slave computers. The algorithm is implemented on a PC cluster and applied to the minimum weight design of steel structures. The results show that the computational time required for structural optimization process can be drastically reduced and the dependency on the parameters can be avoided.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1458-1466
• /
• 2004

Deterministic optimum designs that are obtained without consideration of uncertainties could lead to unrealiable designs. Such deterministic engineering optimization tends to promote the structural system with less reliability redundancy than obtained with conventional design procedures using the factor of safety. Consequently, deterministic optimized structures will usually have higher failure probabilities than unoptimized structures. This paper proposes the reliability based design optimization technique fur apressure tank considering temperature effect. This paper presents an efficient and stable reliability based design optimization method by using the advanced first order second moment method, which evaluates a probabilistic constraint for more accuracy. In addition, the response surface method is utilized to approximate the performance functions describing the system characteristics in the reliability based design optimization procedure.

• Structural Engineering and Mechanics
• /
• v.4 no.1
• /
• pp.25-35
• /
• 1996

This paper describes a continuum variational formulation for design optimization of nonlinear structures in the elastic-plastic domain, where unloading and reloading of the structures are allowed to occur. The Total Lagrangian procedure is used for the description of the structural deformation. The direct differentiation approach is used to derive the sensitivities of the various structural response measures with respect to the design parameters. Since the material goes into the inelastic range and unloading and reloading of the structure are allowed to occur, the structural response is path dependent and an additional step is needed to integrate the constitutive equations. It can be shown, consequently, that design sensitivity analysis is also path-dependent. The theory has been discretized by the finite element technique and implemented in a structural analysis code. Mathematical programming approach is used for the optimization process. Numerical applications on trusses are performed, where cross-sectional areas and nodal point coordinates are treated as design variables. Optimal designs have been obtained and compared by using two different strategies: a two level strategy where the levels are defined accordingly the type of design variables, cross sectional areas or node coordinates, and optimizing simultaneously with respect to both types of design variables.