• Korean Journal of Crystallography
• /
• v.11 no.4
• /
• pp.195-199
• /
• 2000

Ceramics based on CaTiO₃-NdAlO₃ solid solutions were synthesized in order to study their dielectric microwave properties. Microstructural analysis was performed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) using different analytical methods such as energy-dispersive X-ray spectroscopy (EDXS). It was observed that the heating conditions during sintering and cooling strongly affect the microstructural development of CaTiO₃-NdAlO₃-based ceramics. Various types and concentrations of structural defects were identified, for example, dislocations, twins and/or antiphase boundaries. all such defects resulted in a degradation of the dielectric microwave properties, in particular the quality factor Q. Dielectric properties of CaTiO₃-NdAlO₃-based ceramics can be improved by an appropriate thermal treatment of ceramics which results in a decrease in the concentrations of the identified microstructural defects.

• International Journal of Railway
• /
• v.5 no.1
• /
• pp.22-28
• /
• 2012

This report is devoted to the problems of Mongolian Railway Transportation Safety such as high length of wagon service life, defects due to the more factors of exploitation, idle time, increase of faults, poor condition of repairing shops and more hand and mechanical operations and these conditions are quite difficult to meet the safety and reliability of increasing transportation from day to day. The paper discusses that the most optimum solution is diagnosing before occurring wear, breakdown, and defects on the basis of studying characteristics of structural material breakdown, residual methods of voltage, effects of material hardness and linear defects of a crystal net and the reform of machines is very important to implement it. It focuses the structures, characteristics of the material transportation and tests and analyses of the wagon cart which has to meet the traffic safety of wagons and slow and soft movement. The study is done on the wagon chassis which has to meet the traffic safety of luggage wagons.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.140-145
• /
• 2001

The tape carrier package(TCD) is one of the most important components in a liquid crystal display(LCD) module. It has a role to transmit electrical signals from a printed circular board(PCB) to a display panel. If TCP is damaged under mechanical shock, the signals can not be transmitted to the panel and as a result, some dead lines are generated on the panel. This kind of phenomenon is commonly called as 'line defects'. In this paper, new structural design concepts of TCP are proposed to guarantee its reliability by using Taguchi's approach and dynamic FE-analysis. The line defects problem of TCP module is solved by replacing the original TCP with the newly designed one.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.29-46
• /
• 1999

The performance based design obligates quantitative assessment of required performances by means of transparent and objective science. In this design scheme, simulation of both macro and micro-scale structural behaviors is thought to be a powerful tool. This paper proposes a way how to unify the structural safety and serviceability check method and durability assessment of RC structures. Though component chemical-physical processes are crudely assumed, system dynamics of micro-scale pore structure formation and macro-scale defects and deformation of structures was shown as possible and promising approach in future. The authors understand that the unification of structural and durability design has just started. For further progress and development, predictive tool of structural behaviors from birth to death of concrete under any specified environment and load serves as an essential technicality.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.207-212
• /
• 2014

Aluminum-doped zinc oxide (AZO) films were deposited on SiOC/Si wafer by an RF-magnetron sputtering system, by varying the deposition parameters of radio frequency power from 50 to 200 W. To assess the correlation of the optical properties between the substrate and AZO thin film, photoluminescence was measured, and the origin of deep level emission of AZO thin films grown on SiOC/Si wafer was studied. AZO formed on SiOC/Si substrates exhibited ultraviolet emission due to exciton recombination, and the visible emission was associated with intrinsic and extrinsic defects. For the AZO thin film deposited on SiOC at low RF-power, the deep level emission near the UV region is attributed to an increase of the variations of defects related to the AZO and SiOC layers. The applied RF-power influenced an energy gap of localized trap state produced from the defects, and the gap increased at low RF power due to the formation of new defects across the AZO layer caused by lattice mismatch of the AZO and SiOC films. The optical properties of AZO films on amorphous SiOC compared with those of AZO film on Si were considerably improved by reducing the roughness of the surface with low surface ionization energy, and by solving the problem of structural mismatch with the AZO film and Si wafer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1618-1625
• /
• 2006

During the last two decades, several guidelines have been developed and used for assessing the integrity of a defective steam generator (SG) tube that is generally caused by stress corrosion cracking or wall-thinning phenomenon. However, as some of SG tubes are also failed due to fretting and so on, alternative failure estimation schemes are required for relevant defects. In this paper, parametric three-dimensional finite element (FE) analyses are carried out under internal pressure condition to simulate the failure behavior of SG tubes with different defect configurations; elliptical wear, tapered and flat wear type defects. Maximum pressures based on material strengths are obtained from more than a hundred FE results to predict the failure of SG tube. After investigating the effect of key parameters such as defect depth, defect length and wrap angle, simplified failure estimation equations are proposed in relation to the equivalent stress at the deepest point in wear region. Comparison of failure pressures predicted by the proposed estimation scheme with corresponding burst test data showed a good agreement.

• Smart Structures and Systems
• /
• v.33 no.1
• /
• pp.41-53
• /
• 2024

Grouting sleeves are an essential connecting component of prefabricated components, and the quality of grouting has a significant influence on structural integrity and seismic performance. The embedded grouting sleeve (EGS)'s grouting defects are highly undetectable and random, and no effective monitoring method exists. This paper proposes an ultrasonic guided wave method and provides a set of guidelines for selecting the optimal frequency and suitable period for the EGS. The optimal frequency was determined by considering the group velocity, wave structure, and wave attenuation of the selected mode. Guided waves are prone to multi-modality, modal conversion, energy leakage, and dispersion in the EGS, which is a multi-layer structure. Therefore, a time-reversal (TR)-based multi-mode focusing and dispersion automatic compensation technology is introduced to eliminate the multi-mode phase difference in the EGS. First, the influence of defects on guided waves is analyzed according to the TR coefficient. Second, two major types of damage indicators, namely, the time domain and the wavelet packet energy, are constructed according to the influence method. The constructed wavelet packet energy indicator is more sensitive to the changes of defecting than the conventional time-domain similarity indicator. Both numerical and experimental results show that the proposed method is feasible and beneficial for the detection and quantitative estimation of the grouting defects of the EGS.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.3
• /
• pp.11-20
• /
• 2022

The main purpose of this study is to investigate the applicability of the shear wave tomography technology as a non-destructive testing method to evaluate the debonding between the track concrete layer (TCL) and the hydraulically stabilized based course (HSB) of concrete slab tracks for the Korea high-speed railway system. A commercially available multi-channel shear wave measurement device (MIRA) is used to evaluate debonding defects in full-scaled mock-up test specimen that was designed and constructed according to the Rheda 200 system. A part of the mock-up specimen includes two artificial debonding defects with a length and a width of 400mm and thicknesses of 5mm and 10mm, respectively. The tomography images obtained by a MIRA on the surface of the concrete specimens are effective for visualizing the debonding defects in concrete. In this study, a simple image processing method is proposed to suppress the noisy signals reflected from the embedded items (reinforcing steel, precast sleeper, insert, etc.) in TCL, which significantly improves the readability of debonding defects in shear wave tomography images. Results show that debonding maps constructed in this study are effective for visualizing the spatial distribution and the depths of the debondiing defects in the railway concrete slab specimen.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.630-633
• /
• 2006

In this study, we concerned the steel cap and head part arrangement of PHC pile structure to complement existing construction process which have the defects such as highly hazardous circumstance for safety concerns and retard a term of works. The steel cap developed for supplement the stiffness between extend foundation and contact section of PHC pile that is based on structural theory. The experiments have been performed to evaluate the characteristics of behavior between head part of PHC pile using steel cap and extend foundation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.45-50
• /
• 2005

During oxidation process, several type of defects are formed on the surface of the silicon crystal which was damaged mechanically before oxidation. As the size of abrasive particle increases multiple dislocation loops are produced favorably over oxidation-induced stacking faults, which are dominantly produced when ground with finer abrasive particle. These defects are not related with the crystal growth process like Czochralski or directional solidification. During directional solidification process, twins and stacking faults are the two major defects observed in the bulk of the silicon crystal. On the other hand, slip dislocations produced by the thermal stress are not observed. Thus, not only in single crystalline silicon crystal but also in multi-crystalline silicon, extrinsic gettering process with programmed production of surface defects might be highly applicable to silicon wafers for purification.