• 한국의류산업학회지
• /
• 제2권5호
• /
• pp.437-442
• /
• 2000

In this paper, in order to examine the torsional behaviour of twisted yarn closely, the torsional rigidity would be derived in terms of physical and mechanical characteristics of its constituent fibers and yarn structural parameters by energy-method. And the propriety of the theory will be discussed by comparing with experimental results. The torsional rigidity of yarn in both experimental and theoretical results decreases with surface helix angle increases. But the experimental values are more higher than those of the theoretical ones.

• Steel and Composite Structures
• /
• 제19권2호
• /
• pp.405-416
• /
• 2015

We proposed the concept of nominal rigidity of a long-span V-shaped rigid frame composite arch bridge, analyzed the effects of structural parameters on nominal rigidity, and derived a theoretical nominal rigidity equation. In addition, we discussed the selection of the arch-to-beam rigidity ratio and its effect on the distribution of internal forces, and analyzed the influence of the ratio on the internal forces. We determined the delimitation value between rigid arch-flexible beam and flexible arch-rigid beam. We summarized the nominal rigidity and arch to beam rigidity ratios of existing bridges. The results show that (1) rigid arch-flexible beam and flexible arch-rigid beam can be defined by the arch-to-beam rigidity ratio; (2) nominal rigidities have no obvious differences among the continuous rigid frame composite arch bridge, V-shaped rigid frame bridge, and arch bridge, which shows that nominal rigidity can reflect the global stiffness of a structure.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.337-344
• /
• 2001

This paper is concerned with the change of joint rigidity in estimating the degree of semi-rigidity of connections and the buckling load in a single layer latticed dome. The estimations are based on information about the ratio for the rotational stiffness of the connection to the flexural stiffness of the member and the minimum eigenvalue of a structure for pinned, semi-rigid and completely rigid cases, respectively. Connection characteristics are reflected in the ratio control of joint rigidity for the DOFs to be related using the spring element by FEM.

• KCI Concrete Journal
• /
• 제14권3호
• /
• pp.111-120
• /
• 2002

This study proposes a joint model consisting of different types of members as a new structural system, and then investigates the resulting structural behavior. The joint model consists of a concrete-filled steel tube column (CFT) together with a steel reinforced concrete at the end plus reinforced concrete beam at the center. For comparison, two other joint models were designed, that are, a CPT with a reinforced concrete beam, and a CFT with a steel reinforced concrete at the end plus steel concrete beam at the center, then their joint capacity and rigidity, energy absorption capacity, etc., were all investigated. From the results, the CFT column with a steel reinforced concrete at the end plus steel concrete beam at the center was outstanding in terms of its capacity and rigidity. The results of this analysis demonstrate that an adequate connection type and reinforcement method with different materials of increasing the rigidity, thereby producing a capacity improvement along with protection from pre-fractures.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.253-259
• /
• 2000

This thesis investigated the behavior of super structure by varying the factors such as the change of pile rigidity, the characteristics of soil and the constraint condition of support. The results of this study are as follows; 1. The pile rigidity in the Fig 3.3 computed by the rotating deformed plane method becomes the elastic range at approximately about 5.1 m (D : 1.0 m) below the ground level. This result is consistent with the previous study that the pile deformation occurs approximately 3 to 6 times pile diameter from the pile head. 2. The values of forces and deformations for the structure-pile system in Y-direction appeared larger than that in X-direction, since the pile rigidity and constraint condition of support were changed as shown Fig.3.5 to 3.8. 3. The current practice for the analysis of structure-pile system has not considered the variation of pile rigidity and the constraint condition of support. So, the analysis of structure-pile system with large difference in super-structure rigidity must includes these factors in both X and Y directions.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.195-198
• /
• 2002

Two types of conformal load-bearing antenna structure (CLAS) were designed with microwave composite laminates and Nomex honeycomb cores, to give both structural rigidity and good electrical performance. One is 4$\times$8 array for Synthetic Aperture Radar(SAR) system and the other is $5\times2$ array for wireless LAN system. Design was based on wide bandwidth, high polarization purity, low loss and good structural rigidity. We studied the design, fabrication and structural/electrical performances of the antenna structures. The flexural behavior was observed under a 3-point bending test, an impact test, and a buckling test. Electrical measurements were in good agreement with simulation results and these complex antenna structures have good flexural characteristics. The design of this antenna structure is extended to give a useful guide for sandwich panel manufacturers as well as antenna designers.

• 한국강구조학회 논문집
• /
• 제12권4호통권47호
• /
• pp.445-455
• /
• 2000

본 연구는 최근의 건설 환경 변화에 따른 여러 가지 제문제점들에 대한 구조적 측면에서의 대응책의 하나로서 새로운 구조 시스템 전개를 위해 이종구조부재로 구성된 보기둥 접합부 모델을 제안한 것이다. 본 연구에서는 장스팬 S보의 강성을 향상시키기 위해 S조의 단부를 RC조로 보강하여 강성 및 내력증대를 꾀하였으며, 이종구조 사이의 원활한 응력 전달을 목적으로 SRC조 단부의 보 주근은 U자형 갈고리 모양으로 정착하여 철골 플랜지에 용접 접합하였다. 일련의 실험을 통해 접합부 강성 및 내력 특성을 고찰하였고 본 접합부의 가능성을 제시하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권3호
• /
• pp.243-250
• /
• 2004

SPS 공법에서 철골보는 가설상태에서 띠장을 지지하는 버팀대로 사용되며, 시공후 구조물에서 휨재의 역할을 한다. 기존 실험연구결과에서 RC 띠장-철골보 접합부는 소정의 휨강성을 갖는다고 보고하고 있다. 본 연구에서는 SPS 공법으로 시공된 지하복합골조에 대하여 RC 띠장-철골보 스터드 접합부의 고정도에 따른 거동을 평가하기 위하여 비선형 해석을 실시하였다. 해석변수는 시공단계, 횡력의 크기, RC 띠장-철골보 접합부의 고정도 등이다. 해석결과에서 골조의 항복과정, 보 중앙부 휨모멘트 및 처짐에 대한 접합부의 고정도의 영향을 보여준다.

• Structural Engineering and Mechanics
• /
• 제21권6호
• /
• pp.677-698
• /
• 2005

In engineering practice, tubular connections are usually assumed pinned or rigid. Recent research showed that tubular joints may exhibit non-rigid behavior under axial or bending loads. This paper is concerned with establishing a new classification for tubular joints and investigating the effect of joint rigidity on the global behavior of CHS (Circular Hollow Section) lattice girders. Parametric formulae for predicting tubular joint rigidities are proposed, which are based on the finite element analyses through systematic variation of the main geometric parameters. Comparison with test results proves the reliability of these formulae. By considering the deformation patterns of respective parts of Vierendeel lattice girders, the boundary between rigid and semirigid tubular connections is built in terms of joint bending rigidity. In order to include characteristics of joint rigidity in the global structural analysis, a type of semirigid element which can effectively reflect the interaction of two braces in K joints is introduced and validated. The numerical example of a Warren lattice girder with different joint models shows the great effect of tubular joint rigidities on the internal forces, deformation and secondary stresses.

• 한국공간구조학회논문집
• /
• 제2권4호
• /
• pp.45-52
• /
• 2002

Research about spherical shells been applying most usually is achieved by many investigators already and generalized equation has been derived. But, existent research is limited in case that spherical shell's roof rigidity is isotropy or orthotropy, and research that consider periodicity of rigidity-distribution that can happen by doing spherical shell's roof system by lattice system is not gone entirely. The purpose of this paper is applying Galerkin method to spherical shell that model periodicity of roof rigidity distribution that appear by roof lattice form of large space structure and develop structural analysis program that formularize. Rigidity-model of this research selects that of spherical shell which has 2-way grid. In this paper, buckling-strength and deformation distribution of isotopic spherical shell and 2-way grid spherical shell obtained by developed program could confirm the reliability by comparison with result of existent research.