• Journal of the Korean GEO-environmental Society
• /
• v.7 no.3
• /
• pp.69-76
• /
• 2006

In this study, an experimental study in sand ground that was prepared by raining method was performed for modeling the bearing capacity behavior of strip footing above a cavity. The critical range of bearing capacity of the strip footing affected by underground cavity was investigated by comparing results between experiment and theory. The size of the critical region depends on several factors such as footing shape, soil property, cavity size and cavity shape. The ultimate bearing capacity was more influenced by the depth of the underground cavity than the eccentricity of the underground. In addition, an underground cavity influences on not only the decrease of the bearing capacity, but also the differential settlement of a strip footing.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.1-6
• /
• 1997

An analysis method for the electromagnetic scattering of a tE polarized plane wave from a periodic strip grating over a grounded dielectric slab is consisered from the viewpoint of reflectio ngraing problem. The strip gratings showing bragg and off-bragg balzing phenomena at the frequency of 10GHz are designed, respectively. The strip grating structure is implemented using aluminum plate (hround conductor), paraffin(dielectric material ; .xi.$_{\gamma}$=2.24) and copper (strip conductor ; 0.08mm thickness). The experimental results (reflection power) for bragg as well as off-bragg blazing phenomenon have been compared with the theoretical results and fairly good agreements between theory and experiment have been observed.ed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.10
• /
• pp.3408-3414
• /
• 1996

This paper investigated plane strain stress intensity factors caused by thermal impact on a center-crack strip. The crack was aligned perpendicularly to the strip boundary. The problem was analysed by determining the dislocation density function in the singular integral equations formulated by the dislocation theory. Under the abrupt temperature change along the edge, the center crack behaved as a mode I crack due to the symmetric geometry. The value of maximum stress intensity factor monotonically increased until the ratio of dimensionless crack length approached to about 0.3, followed by gradual decrease. As a result, a critical corresponding crack length was determined.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.1
• /
• pp.126-133
• /
• 2014

For boarding comfort and pleasant boarding sensitivity of passenger in passenger ship, there are a few methods such as motion sickness rate or MSI(Motion Sickness Incidence) to assess safety of passenger ship. To find out MSI or motion sickness rate of the training vessel Kaya of Pukyong National University, we use lots of various factors: sea condition, incident angle in main sail way, economic speed, calculation position of motion sickness, sea state, work place and reduce zone of ship. In this paper, we adopted Maxsurf Seakeeper program based on Strip Theory and carefully compared theoretical results with experimental results.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.186-191
• /
• 2001

A crack with electrically impermeable surfaces in an electrostrictive material subjected to uniform electric loading is analysed. The effect of electric yielding on stress intensity factor is investigated by using a small scale yielding model and a strip yield zone model. Complete forms of electric fields and elastic fields are derived by using complex function theory. The electrical yield zone shapes for two models are different each other. The two models, however, predict similar yield zone sizes under the small scale yielding conditions. It is found that the influence of electric yielding on the stress intensity factor is insensitive to the modeling of the electrical yield zone shape.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.3
• /
• pp.173-179
• /
• 2017

This paper analyzes actuator characteristics for main wing and tail surfaces of an ornithopter by using a motion capture test. Experiments with the ornithopter are conducted indoor, and its fuselage is held on a jig to reduce interaction with vibration generated by flapping motion. The motion capture system detects the movement of markers attached on the main wing and tail wing tip. Experimental results show that the main wings tend to change its amplitude according to the flapping frequency, and the lift and thrust generation simulation is implemented by applying the experimental results and the ornithopter specification to Modified Strip Theory. Step input excitation is applied for experimental analysis of the tail wing in horizontal and vertical directions. As a result, horizontal and vertical tail wings have different characteristics in terms of overshoot, final value, damping ratio and natural frequency because they have different wing structures and linkages.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.7 s.144
• /
• pp.909-917
• /
• 2005

Based on the theory that formation of Korean Men's Traditional Trousers is related to Mobius strip, this study researches correlation between distinctive construction of Korean Men's Traditional Trousers and historical background based on old documents and restoration. Distinctive construction of Korean Men's Traditional Trousers are as follows. First, Korean Men's Traditional Trousers is manufactured just like Principle of Mobius strip that the square is twisted once, considering its materials' conditions. Second, Korean Men's Traditional Trousers, manufactured larger, feature cubic effect and twisted formative beauty because its waist and ankle parts are tightened with bands. Third, Korean Men's Traditional Trousers, composed of big Sapok and small Sapok in oblique, are suitable for active play due to its high functionality.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.73-81
• /
• 1991

In order to simulate the ceramic filter in the state of the one-strip electrode, the theory has been analyzed and a computer program has been developed using the energy trapping effect. The ceramic filters were fabricated using the PZT-4 specimen. The necessary condition that the ceramic filter has the energy trapping effect is that the electroded portion frequency should be smaller than the unelectroded portion frequency when the wave number is zero. Each of the average differences of the resonant point and bandwidth between by the theoretical calculations and by experiment results was 5.6[%] and 3.72[%]. It is considered that the one-strip ceramic filter having a desired characteristics and the lowest difference can be fabricated easily by means of the simulation developed in this paper and the fabrication methods.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.253-257
• /
• 2001

This study reveals the sheet metal working with multi-forming type ultra precision process. They require analysis of many kinds of important factors, i.e. theory and practice of metal press working and its phenomena, die structure, machining condition for die making, die material, heat treatment of die components, know-how and so on. In this study, we designed and constructed a multi-forming ultra precision progressive die as a bending and drawing working of multi-stage and performed through the try out for thin sheet metal. This part I of papers related to the analysis of production part and strip process layout design through the metal forming simulation by DEFORM and IDEAS.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.86-91
• /
• 2002

The production part requiring multiple processes such as piecing, blanking and notching, are performed with a high production rates in progressive die. In order to prevent the dejects of process result, the optimum of strip process layout design, die design, die making, and tryout with inspection etc. are needed. According to these factors of die development process, they required theory and practice of metal working process and its phenomena, die structure, machining conditions for die making, die materials, heat treatment of die camponents, know-how and so on. In this study, we designed and analyzed die camponents also simulated the strip process layout of multiple stage drawing by DEFORM. Especially the result of tryout and its analysis become to the feature of this study.