• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.38-44
• /
• 2020

Surface texturing of micro-dimples has been used in many manufacturing industries to reduce friction between two sliding contacted surfaces. Surface texturing decreases the frictional force owing to minimizing of the sliding contact area. In this paper, micro-dimples have been fabricated on an Al6061-T6 surface using a two-frequency elliptical vibration texturing (TFEVT) method. A high-frequency of 18 kHz and low-frequency of 250 Hz were applied to an elliptically-vibrated tool holder. The Stribeck curve was plotted to analyze the friction coefficient trends. Furthermore, the representative wetting index, such as the water contact angle (WCA), was measured by considering the friction coefficient. WCA is associated with micro-dimple density and associated parameters. Consequently, the dimpled surfaces with a low friction coefficient exhibited a relatively high WCA in the feed direction. According to the Stribeck curve, the dimpled surfaces demonstrate superior friction performance for mixed-film lubrication compared to the non-textured surface.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.945-950
• /
• 2004

Surface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction.Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.

• 한국정밀공학회지
• /
• 제24권1호
• /
• pp.79-84
• /
• 2007

Some surface pattern of tribological application is an attractive technology of engineered surface. Therefore, friction reduction is considered to be necessary for improved efficiency of machine. This study investigated the effect of friction property for angles of micro-crosshatch groove surface pattern on bearing steel using pin-on-disk test. We obtain sample which can be fabricated by photolithography process. We discuss the friction property depend on an angle of crosshatch groove surface pattern. We can verify the lubrication mechanism as Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter under the lubrication condition. It was found that the friction coefficient was related to angle of crosshatch groove pattern on contact surface.

• 한국기계가공학회지
• /
• 제10권3호
• /
• pp.94-99
• /
• 2011

Micro-scale surface pattern has an benefit of tribological application under lubricated sliding contact. Therefore, a special pattern, that has to reduce the coulomb friction under contact, is considered to be necessary for improved efficiency of machines. The current study investigated the friction property of angle effect for micro-scale grooved crosshatch pattern on bearing steel surface using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of hatched-angle on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.29-35
• /
• 1988

When low sliding velocities in the boundary lubrication range are operating, irregular movements frequently occur which are a result of the stick-slip phenomenon. Such slide motions are undesirable in precision machine tools, particularly with feed back systems used in numerical and adaptive control machine tools. Accordingly, this paper reports analytical and experimental studies in the stick-slip characteristic of machine tool feeding system. The main conclusions of this study are as follows; The tendency towards stick-slip effects may be reduced by; 1). Reducing the drop in friction coefficient in the Stribeck curve(on the rising part of the friction characteristic at higher sliding speeds, the system is stable all the time) 2). Reducing the transition velocity by the use of a higher viscosity lubricating oil. 3). Increasing the stiffness(Damping)and reducing normal load(Sliding mass) Therefore, the Critical velocity is decided from the above conclusions and in designing of machine tool, feed rates(sliding velocity)must be design the more than critical velocity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.249-253
• /
• 1994

In machine tools, frictional force exists between the table and the bed, and in ballscrews. In this paper, feed motor current is used to measure the motor torque and frictional force. A hall sensor is used to measure the feed motor current. Some frictional pheonomina in feed drice systems, such as, the relationship between feedrate and frictional force, lubrication conditions and frictional force, and feed direction and frictional force, are obtained. Generally, the friction behavior is in good agreement with Stribeck's curve. However, the data shows significant scatter when feedrate is high.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.188-193
• /
• 2005

Surface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.

• 한국기계가공학회지
• /
• 제10권2호
• /
• pp.110-116
• /
• 2011

The current study investigated the friction property of angle and width effect for micro-scale grooved crosshatch pattern on SKD11 steel surface against bearing steel using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of a hatched-angle and a width of groove on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. So It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction. Also, it is play an important a width of groove to be improved the friction property. I was found that friction property has a relationship between a width and an angle for micro-grooved pattern.

• KSTLE International Journal
• /
• 제6권2호
• /
• pp.51-57
• /
• 2005

Surface texturing of tribological applications is an attractive technology of engineered surface. Therefore, reduction of friction is considered to be necessary for improved efficiency of machines. The current study investigated the potential of textured micro-scale grooves on bearing steel flat mated with pin-on-disk. We discuss reducing friction due to the influence of sliding direction at surface pattern. We can indicate lubrication mechanism as a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for the lubrication condition. It was found that the friction coefficient was changed by the surface pattern and sliding direction, even when surface pattern was the same. It was thus verified that micro-scale grooves could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions. The lubrication regime influences the friction coefficient induced by the sliding direction of groove pattern. The friction coefficient depends on a combination of resistance force and hydrodynamic.

• 대한기계학회논문집A
• /
• 제38권9호
• /
• pp.1005-1012
• /
• 2014

기어의 구동은 여러 기계요소에서 동력전달을 가능하게 해주는 가장 중요한 요소이다. 이러한 기어 접촉면에서의 상태는 마모, 재료의 변형 그리고 윤활 상태에 따라 크게 좌우되며, 이러한 상태 변화는 기어의 수명에 큰 영향을 준다. 따라서, 이러한 상태 진단에 대한 해법은 원활한 구동을 위한 필수요소이다. 기어의 상태 변화는 연마 마모(Abrasive wear), 점식 (Pitting), 스커핑(Scuffing), 스폴링(Spalling) 등을 유발하며, 이러한 마모들은 기어로부터 발생하는 진동 레벨을 상승시킨다. 본 연구에서는 스퍼 기어를 장착한 기어 박스를 이용한 실험적 연구를 통해 기어의 표면 피로 마모를 평가하기 위해 진동 신호로부터 구해진 통계적 변수들과 Stribeck Curve 와의 상관관계를 검증하였다.