• 한국지반공학회지:지반
• /
• 제12권6호
• /
• pp.153-162
• /
• 1996

이방압밀이 과압밀점토의 비배수크리프파괴거동에 미치는 영향을 연구하기 위하여 등방 및 이방과압일시킨 점토시료에 대해서 비배수상태에서 크리프시험을 수행하였다. 연구결과 비배수 크리프파괴거동은 점토시료의 응력이력 즉 과압밀비와 압밀응력비$(\sigma_{3c}/\sigma_{le})$의 크기에 의해서 영향을 크게 받는다는 사실이 밝혀졌다. 즉 점토의 크리프강도는 과압밀비와 압밀응력비가 클수록 증가하므로 정지토압계수가 1.0보다 작은 점토지반의 크리프파괴 가능성을 등방압밀크리프피 괴시험에 의해서 판단하는 것은 위험하다. 그리고 점토의 크리프강도는 과압밀비와 압밀응력비의 크기에 관계없이 Finn과 Shead(1973)의 제안식에 의한 상한항복강도로서 구할 수 있었다.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.49-55
• /
• 2020

Creep rupture data for Alloy 690 steam generator tubes in a pressurized water reactor are essentially needed to demonstrate a severe accident scenario on thermally-induced tube failures caused by hot gases in a damaged reactor core. The rupture data were obtained using the tube specimens under different applied-stress levels at 650℃, 700℃, 750℃, 800℃, and 850℃. Important creep constants were proposed using various creep laws in terms of Norton power law, Monkman-Grant (M-G) relation, damage tolerance factor (λ), and Zener-Hollomon parameter (Z). In addition, a creep activation energy (Q) value for Alloy 690 tube was reasonably determined using experimental data. Creep behaviors such as creep strength, creep rates, rupture elongation showed the results of temperature dependence well. Modified M-G plot improved a correlation of the creep rate and rupture life. Damage tolerance factor for Alloy 690 tubes was found to be λ =2.20 in an average value. Creep activation energy for Alloy 690 tube was optimized for Q=350 (kJ/mol). A plot of Z parameter obeyed a good linearity, and the same creep mechanism was inferred to be operative in the present test conditions.

• 대한토목학회논문집
• /
• 제30권2A호
• /
• pp.185-191
• /
• 2010

콘크리트 구조물의 사용성과 내구성 저하의 원인이 되는 균열은 응력의 크기, 응력구배 및 기타 구조적 재료적 원인 등에 의하여 발생하기 때문에 콘크리트의 균열강도를 정확히 예측하기는 매우 어렵다. 특히 판구조의 경우 기존의 일축휨강도에 의한 균열평가가 실제 구조물의 균열강도와 상이할 수 있다. 본 연구에서는 이축휨인장강도 평가에 적합한 시험체 제원을 적용하여 일축과 이축휨강도 특성을 비교, 평가하였다. 실험결과 골재의 크기 및 실험체 크기의 증가에 따라 일축 및 이축휨강도 모두 강도가 저하되는 것으로 나타났다. 일축휨강도에 비하여 이축휨강도가 일축휨강도의 39.5~99.2%로서 전반적으로 낮은 강도를 갖는 것으로 평가되었으며, 특히 20 mm 골재를 사용한 경우에는 76%정도로 고찰되었다.

• Architectural research
• /
• 제11권1호
• /
• pp.25-33
• /
• 2009

This study presents the testing of 15 hwangtoh-based cementless concrete mixes to explore the significance and limitations of the development of eco-friendly concrete without carbon dioxide emissions while maintaining various beneficial effects. Hwangtoh, which is a kind of kaolin, was incorporated with inorganic materials, such as calcium hydroxide, to produce a cement-less binder. The main variables investigated were the water-to-binder ratio and fine aggregate-to-total aggregate ratio to ascertain the reliable mixing design of hwangtoh-based cementless concrete. The variation of slump with elapsed time was recorded in fresh concrete specimens. Mechanical properties of hardened concrete were also measured: including compressive strength gain, splitting tensile strength, moduli of rupture and elasticity, stress-strain relationship, and bond resistance. In addition, mechanical properties of hwangtoh-based cement-less concrete were compared with those of ordinary portland cement (OPC) concrete and predictions obtained from the design equations specified in ACI 318-05 and CEB-FIP for OPC concrete, wherever possible. Test results show that the mechanical properties of hwangtoh-based concrete were significantly influenced by the water-to-binder ratio and to less extend by fine aggregate-to-total aggregate ratio. The moduli of rupture and elasticity of hwangtoh-based concrete were generally lower than those of OPC concrete. In addition, the stress-strain and bond stress-slip relationships measured from hwangtoh-based concrete showed little agreement with the design model specified in CEB-FIP. However, the measured moduli of rupture and elasticity, and bond strength were higher than those given in ACI 318-05 and CEB-FIP. Overall, the test results suggest that the hwangtoh-based concrete shows highly effective performance and great potential as an environmental-friendly building material.

• 한국재료학회지
• /
• 제2권6호
• /
• pp.468-476
• /
• 1992

초기 결정입 크기 15${\mu}$m인 W-0.2wt%Ni, 1시간 30분과 W-0.4wt%Ni, 1시간 소결체의 응력 파단 성질 및 파괴 양상을 조사하기 위해서 direct load creep tester를 사용, 100$0^{\circ}C$~120$0^{\circ}C$, 수소분위기에서 응력 파단 시험을 행하였다. 100시간 응력 파단 강도는 W-0.4wt%Ni이 W-0.2wt% Ni보다 23% 크게 나타났다. 이것은 시험 중 결정입 성장에 따른 영향 때문으로 생각된다. W-0.2wt%NI에서 크리프 속도와 초기 결정입 크기와의 관계는 반비례하는 경향을 보였다. 활성 소결체에서 Ni 첨가량이 증가함에 따라, 단위 면적당 기공의 밀도 및 크기는 작아지고, 형태는 구형화 되어 미세균열로의 전이가 어려워 응력 파단 성질이 향상되었다. 응력 파란 시험 후, 각단면은 전형적인 입계파괴 양상을 나타내었다. 이는 소결 과정 중 생성된 기공들이 결정입계를 따라 전파하였기 때문으로 생각된다.

• Journal of Biosystems Engineering
• /
• 제17권2호
• /
• pp.156-170
• /
• 1992

The force-deformation relationship gives the basic physical properties of the fruits such as the bioyield point, the rupture point, and the deformations at the bioyield point and the rupture point. These informations are very important to study the stress-strain relationships of the fruits. This study was conducted to analyze those physical properties according to the sampling position of the fruits, and to determine the bioyield point, the rupture point, and the deformations at the bioyield point and the rupture point of the fruits for two different storage conditions(low temperature and normal temperature) and the storage period, and to investigate the effect of loading rate on those physical properties, the hysteresis on the loading-unloading condition and the degree of elasticity of the fruits. The results of the study were as follows : 1. The physical properties(BS, US, BD, and RD) of the test specimen selected from the different sampling positions were quite different. The values of the physical properties were shown smallest ones at the cheek of the fruits, and the statistical test results of the physical properties between the cheek from the other two positions of the fruits showed that there were significant difference at the 1 % level between them. 2. The effect of loading rate on the physical properties of the fruits was relatively large, all the considered physical propertis of the fruits increased with the loading rate, but the hysteresis loss decreased with it. 3. The physical properties of the fruits according to the storage conditions and period showed different, and the bioyield deformation and the rupture deformation of the fruits increased with the storage period, but the bioyield strength and the ultimate strength of the fruits decreased with it. The effect of the storage conditions on the those physical properties showed that the normal temperature storage condition was a little higher than the low temperature storage condition. 4. As a whole, it was shown that the bioyield strength and the ultimate strength of the pear decreased a little faster than those of the apple, and the bioyield deformation and rupture deformation of the pear increased a little faster than those of apple at the two storage conditions.

• 한국공작기계학회논문집
• /
• 제11권4호
• /
• pp.54-61
• /
• 2002

Inconel 690 alloy has widely been used in power plant and high temperature facilities because it has high thermal resistance and toughness. But we have little design data about the creep behaviors of the alloy. Therefore, in this study, an apparatus has been designed and built for conducting creep tests under constant load conditions. A series of creep tests on Inconel 690 alloy have been performed to get the basic design data and life prediction of inconel products and we have gotten the following results. First, the stress exponents decrease as the test temperatures increase. Secondly, the creep activation energy gradually decreases as the stresses become bigger. thirdly, the constant of Larson-Miller Parameters on this alloy is estimated about 10. And last the fractographs at the creep rupture show both the ductile and the brittle fracture according to the creep conditions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.248-253
• /
• 2003

Titanium alloy has widely been used as glasses rim material because it has high specific strength and also is light, harmless to men. But, we have little design data about the creep behaviors of the alloy. Therefore, in this study, an apparatus has been designed and built for conducting creep tests under constant load conditions. A series of creep tests on them have been performed to get the basic design data and life prediction of titanium products and we have gotten the following results. First, the stress exponents decrease as the test temperatures increase. Secondly, the creep activation energy gradually decreases as the stresses become bigger. Thirdly, the constant of Larson-Miller parameters on this alloy is estimated about 13. And last, the fractographs at the creep rupture show both the ductile and the brittle fracture according to the creep conditions.

• Journal of the Korean Wood Science and Technology
• /
• 제25권1호
• /
• pp.8-14
• /
• 1997

Stress wave velocity, wave impedance, and stress wave elasticity of small, clear bending specimens of five domestic softwoods (Pinus densiflora, Pinus koraiensis, Chamaecyparis obtusa, Cryptomeria japonica, and Larix leptolepis) and four tropical hardwoods(Kempas, Malas, Taun, and Terminalia) were correlated with static bending modulus of elasticity(MOE) and modulus of rupture(MOR). The degree of correlation between stress wave parameters and static bending properties was dependent on wood species tested. Stress wave elasticity and wave impedance were better predictors for static bending properties than stress wave velocity for each species individually and for softwood or hardwood species taken as a group, even though elasticity and impedance were nearly equally correlated with static bending properties apparently. Based upon the correlation coefficient between stress wave parameters and static properties, stress wave elasticity and wave impedance were found as stress wave parameters which can be used for the purpose of the reliable and successful prediction of bending properties. The degree of correlation between static MOE and MOR was also different according to wood species tested. Static MOE was nearly as well correlated with MOR as was stress wave elasticity. The results of this research are encouraging and can be considered as a basis for further work using full-size lumber. From the results of this study, it was concluded that stress wave measurements could provide useful predictions of static bending properties and was a feasible method for machine stress grading of domestic softwoods and tropical hardwoods tested in this study.

• 한국안전학회지
• /
• 제3권2호
• /
• pp.35-48
• /
• 1988

Modern technological progress demands the use of materials at high temperature and high pressure. One of the most critical factors in considering such applications - perhaps the most critical one - is creep behavior. In this study the stress exponents n were determined during creep over the temperature range of $90^{\circ}C\;to\;500^{\circ}C$ (0.4 - 0.85 Tm) and stress range of 0.64 kgt/$mm^2$ in order to investigate the creep hehavior. The stress dependence of rapture time (n') were determined over the temperature range of $200^{\circ}C\;to\;240^{\circ}C$ and stress range of 8.13 kgt/$mm^2$ to 9.55 kgt/$mm^2$ in order to investigate to creep rupture property. And the stress transient dip tests were also carried out for the internal stress ${\sigma}i$ over the temperature range of $90^{\circ}C\;to\;500^{\circ}C$ and stress range of 0.64kgt/$mm^2$ to 17.2 kgt/$mm^2$. The creep tests for constant temperature and stress transient dip tests were conducted in air with Al 7075 alloy under constant tensile load. At around the temperature range $200^[\circ}C\;-\;230^{\circ}C$ and the stress level 8.13 - 9.55 (kgt/$mm^2$), the temperature range $280^{\circ}C\;-\;310^{\circ}C$ and the stress level 1.85 - 2.55 (kgt/$mm^2$), the temperature range $380^{\circ}C\;-\;410^{\circ}C$ and the stress 1.53 - 0.91 (kgt/$mm^2$), the stress exponent in had the value of 6.2 - 6.65 but at around the temperature range $90^{\circ}C\;-\;120^{\circ}C$ and the stress level 10 - 17.2(kgt/$mm^2$), the value of 1.3, and at around the temperature range $470^{\circ}C\;-\;500^{\circ}C$, the stress level 0.62 - 1.02 (kgt/$mm^2$) the value of 1-1. Besides these results, at around the temperature $200^{\circ}C\;-\;240^{\circ}C$ the stress dependence of rupture time (n') had the value of 6.3. Finally, it was found that the value n calculated by considering the applied stress dependence of the internal stress were in good agreement with those obtained for the creep test. Then, it was concluded that the change in n was mainly attributed to the difference of the applied stress dependence of the internal stress and the ratio of the internal stress to the applied stress, and the creep rupture life may be represented as.