• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.55-77
• /
• 2012

A Modern Rock TBM is a tunnel excavation method combining the conventional tunnelling method with the mechanized tunnelling method. It is a hybrid system that excavates a tunnel with TBM and supports the ground by ring beam, wire mesh, rock bolt, shotcrete, i.e., conventional tunnelling method. In the Modern Rock TBM, a ring beam is similar to a steel rib in NATM in the way that uses H-beam. But using a ring beam is more effective than a steel rib because it is installed in a closed-circle. Therefore, improving the performance of the ring beam is a key factor for achieving tunnel stability. In this respect, this study introduces a pressurized ring beam that might be functioning more effectively by confining convergence during tunnel excavation. In order to verify the effect of the pressurized ring beam, a three-dimensional numerical analysis was conducted. The numerical analysis confirms an increase in the minimum principal stress and reduction in the plastic strain that triggers excessive displacement. The analysis result also indicates a decrease in the relative displacement occurring after installing the ring beam, and expansion in spacing between the ring beams.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.307-314
• /
• 2016

Shear characteristics of soils can be investigated using various types of shear stress measuring apparatus. Ring shear tests are often applied for examining the residual shear strength under the unlimited deformation. This paper presents drainage-consolidation-shear velocity dependent undrained shear strengths measured in terms of water leakage. A series of ring shear tests were performed under the constant normal stress (50 kPa) and controled shear velocity ranging from 0.01~1 mm/sec under the undrained condition. As a result, undrained shear strengths are dependent on shear velocity. It exhibits that straining hardening behavior is observed for the shear velocity lower than 0.1 mm/sec; however, the strain softening behavior is observed for the shear velocity higher than 0.1 mm/sec. Water leakage can cause the increase in shear stress irrespective of shear velocity. Shear stress increases with increasing amount of water leakage. It is due to the fact that the small grains and water flow out through the rubble edge in the ring shear box. Repetitive saturation and consolidation processes may minimize the error.

• Journal of the Korean Institute of Gas
• /
• v.10 no.2 s.31
• /
• pp.40-46
• /
• 2006

In this paper, the optimized design of a rectangular O-ring groove has been analyzed for a maximum Cauchy stress and maximum strain using the Taguchi method. This method may efficiently optimize the design parameters for an O-ring groove of a LPG filling unit. The computed FEM results indicate that the optimized design parameters can only be drawn by nine experimental numbers of iterations when the Taguchi design technique has been employed with a finite element method. This means that the Taguchi design method is very useful for the optimization design of O-ring rectangular groove geometry. Based on the computed FEM results by the Taguchi design technique, the dimensions of a groove geometry are given as h=2.5 mm, d=2.74 mm, c=0.15 mm, and w=3.0 mm. In this study, the initial compression ratio of O-rings is recommended as 8.7% for a gas supply pressure of 18 $kg/cm^2$.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.149-149
• /
• 2017

The RING (Really Interesting New Gene) finger proteins are known to play crucial roles in various abiotic stresses in plants. In this study, we report on RING finger E3 ligase, ${\underline{O}ryza}$ ${\underline{s}ativa}$ ${\underline{s}alt$-, ${\underline{A}BA}$- and ${\underline{d}rounght}$ stress-${\underline{i}nduced}$ RING finger ${\underline{p}}rotein{\underline{1}}$ gene (OsSAD1). In vitro ubiquitination assay demonstrated that unlike OsSAD1, a single amino acid substitution ($OsSAD1^{C168A}$) of the RING domain showed no E3 ligase activity, supporting the notion that the activity of most E3s is specified by a RING domain. Result of Yeast-Two hybridization, In vivo protein degradation assay supports that OsSAD1 interacting with 3 substrate, OsSNAC2, OsGRAS44 and OsPIRIN1, and mediates proteolysis of 3 substrates via the 26S proteasome pathway. Subcellular localizations of OsSAD1 while approximately 62% of transient signals were detected in cytosol, 38% of signals were showed nucleus. However, transiently expression of OsSAD1 was detected in cytosol 30% while as 70% of nucleus under 200 mM salt treated rice protoplasts. Results of bimolecular fluorescence complementation (BiFC) showed that two nucleus-localized proteins (OsSNAC2 and OsGRAS44) interacted with OsSAD1 in the both cytosol and nucleus. Heterogeneous overexpression of OsSAD1 Heterogeneous overexpresssion of OsSAD1 in Arabidopsis exhibited sensitive phenotypes with respect to Salt-, mannitol-responsive seed germination, seedling growth. In ABA conditions, OsSAD1 overexpression plants showed highly tolerance phenotypes, such as root length and stomatal closure. Our findings suggest that the OsSAD1 may play a negative regulator in salt stress response by modulating levels of its target proteins.

• Composites Research
• /
• v.14 no.2
• /
• pp.8-12
• /
• 2001

Filament Winding Process is a comparatively simple operation in which continuous reinforcements in the form of roving are wound over a rotating mandrel. It is well established and versatile method for storage tanks and pipes for the chemical and other industries. In this study, tensile strength of a filament wound ring specimens were evaluated by a split disk test fixture and a dress disk test fixture. The results obtained from experiments were compared with the theoretical values from the rule of mixtures. The purpose of this paper is the suggestion of an appropriate test method for the evaluation of tensile properties of filament wound structures. The tensile strength of a ring specimen tested by the dress disk test showed better agreement with the theoretical values than those tested by the split disk test because of higher stress concentration in edges of a split disk test fixture. The results showed that the tensile strength of a ring specimen was influenced by the geometry of test fixture, the continuity of fibers, fiber-tension, fiber-end and stress concentration in specimen.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.31-40
• /
• 1998

To predict residual stresses of aluminum ring rolls after quenching and element removal, 2-D and 3-D thermal elasto-plastic analyses were performed. Strains measured by three step sectioning method were directly compared to those analysed using ABAQUS's element removal. Numerical residual stresses after quenching had similar tendency to measured ones after 2 step aging, but the difference between numerical and measured ones was large. The difference is the reason why there are nonuniform residual stress distributions to ring height direction due to small height of ring, It is judged that the increase of ring height will improve the accuracy of measured ones and decrease the difference. By direct comparison between 3-D numerical strains to simulate three step sectioning method and measured ones, the accuracy of measurement and analysis can be improved. It is concluded that there can be predicted the deformation behavior on machining complex shaped large structures with residual stresses.

• THE JOURNAL OF KOREAN ORIENTAL ONCOLOGY
• /
• v.6 no.1
• /
• pp.149-163
• /
• 2000

The cells that make up the body continuously undergo cell division to maintain life, but stress and carcinogens, and physiological stimuli suppress immunological functions in the body and change cells to cancerous cells. The only way to overcome cancer is by treatment through early detection and proper diagnosis. However, because early stage of cancer shows subjective symptoms that are similar to those of other common illnesses, even doctors have difficulty separating cancer from common illnesses in its early stage. However, the Ki(bioenergy) present in our body recognizes and changes to the most minute changes in the body. This method of detecting the change in bioenergy to discover a disease in the early stage to raise treatment success is called the OBET: O-Ring, Bioenergy Test. This method, which is based on the theories of oriental medicine, focuses on tumors, especially malignant tumors, and has shown value in diagnosis and treatment, as witnessed in the clinical applications. The diagnosis method and cases of OBET: O-Ring, Bioenergy Test are presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.1 s.106
• /
• pp.57-65
• /
• 2006

In this paper, we present the principle of virtual work, from which the exact non-linear equations of motion of a rotating ring can be derived, by using the theory of finite deformation. For a thin ring of which the effect of variation in curvature across the cross-section is neglected, the radial displacement and the extensional stress are determined from the principle of virtual work at the steady state where the ring is rotating with a constant angular velocity. And also we formulate systematically the governing equations concerned to the in-plane vibrations and the out-of-plane vibrations at the disturbed state by using the principle of virtual work which is expressed with the disturbed displacements about the steady state. The formulated governing equations are classified by four models along the cases of considering or neglecting all or partly the secondary effects of flexural shear, rotary inertia, circumferential extension, and twist inertia. The natural vibrations of thin rings are analyzed, and its results are compared and discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.585-592
• /
• 2005

In this paper, we present the principle of virtual work, from which the exact non-linear equations of motion of a rotating ring can be derived, by using the theory of finite deformation For a thin ring of which the effect of variation in curvature across the cross-section is neglected, the radial displacement and the extensional stress are determined from the principle of virtual work at the steady state where the ring is rotating with a constant angular velocity. And also we formulate systematically the governing equations concerned to the in-plane vibrations and the out-of-plane vibrations at the disturbed state by using the principle of virtual work which is expressed with the disturbed displacements about the steady state. The formulated governing equations are classified by four models along the cases of considering or neglecting all or partly the secondary effects of flexural shear, rotary inertia, circumferential extension, and twist inertia. The natural vibrations of thin rings are analyzed, and its results are compared and discussed.

• Tribology and Lubricants
• /
• v.39 no.4
• /
• pp.123-132
• /
• 2023

In this study, the expansion, stress, and operating clearance of bearing elements during operation are observed using the inner/outer ring temperature test data of a 3.0×10⁶ DN-class roller bearing. The operating clearance characteristics of inner-/outer-ring cooling (IORC) bearings are compared to those of inner-ring cooling (IRC) bearings. For IRC bearings, the thermal expansion of the outer ring is the most important factor in clearance variation. As a result, the operating clearance is less than the initial clearance of 61 ㎛, and the operating clearance decreases to 0.5 ㎛ at 25,500 rpm. Conversely, the temperature of the outer ring of IORC bearings is lower than that of IRC bearings, so the operating clearance is kept smaller. When the coolant flow rate to the outer ring is approximately 1.5 to 2.0 L/min, the temperature difference between the inner and outer rings is minimized and the operating clearance is maintained at a significantly lower level than IRC bearings. Small operating clearances are expected to be effective in reducing cage slip and skid damage in roller bearings. The results and analysis procedures of this study can be utilized to design of bearing clearance, lubricant flow rate, and assembled interference in the early design stage of aerospace roller bearings.