• Journal of Welding and Joining
• /
• 제22권4호
• /
• pp.59-64
• /
• 2004

The purpose of this study is to investigate the influence of weld bead profiles on stress concentration factors of double V groove butt-welded joints. The influence of three parameters such as toe radii, flank angles and bead heights on the stress concentration factors is studied by finite element analysis. It is shown that the three parameters have similar effects on the stress concentration factors. Finally a formula to estimate the stress concentration factors considering the three parameters and others is proposed and estimated results are compared with the results obtained by finite element analysis.

• 한국해양공학회지
• /
• 제9권1호
• /
• pp.83-91
• /
• 1995

Surface defects in structural members are apt to be origins of fatigue cracks growth, which may cause serious failure of whole structures. Most structure has a part where stress concentrates such as welded joints, corner parts, etc. And then, analysis on crack growth and penetration from these defects, therefore, is one of the most important subjects for the reliability of LBB design. The present paper has performed an experimental and analysis on the fatigue crack propagation by variety in crack length of surface cracked plate with stress concentration part. The crack growth behavior can be explained quantitatively by using Newman-Raju equation and the stress partitioning method proposed by ASME B&P Code Sec. XI. The stress concentration factor $K_t$ has affected on the crack growth. The crack growth after penetration depends upon the initial front side crack length.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.110-119
• /
• 1990

This study is concerned about the stress concentration factor measurement by photoelastic method, for the case of two circular holes arrangement in 3mm semi-infinite plate under tensile load, the ratio of those two circular holes diameter, the ratio of distance apart from circular holes to breadth and the two holes arrangement angle with loading direction were varied. Besides, the measured stress concentration by photoelastic method around one circular hole was compared with that by strain-gage method.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.1014-1020
• /
• 2004

The present work complies the elastic stress concentration factor for a pipe with local wall thinning, based on detailed three-dimensional elastic FE analysis. To cover practically interesting cases, a wide range of pipe and defect geometries are considered, and both internal pressure and global bending are considered. Resulting values of stress concentration factors are tabulated for practical use, and the effect of relevant parameters such as pipe and defect geometries on stress concentration factors are discussed. The present results would provide valuable information to estimate fatigue damage of the pipe with local wall thinning under high cycle fatigue.

• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.1-7
• /
• 1996

용접이음부재에서 피로강도에 큰 영향을 미치는 용접부의 응력집중계수를 추정하였다. 여기서는 하중전달형 십자필렛용접이음부를 그 대상으로 하였다. 필렛용접이음부에서 토우파괴를 일으키는 피로균열발생부인 용접토우부의 응력집중계수를 구하기 위해 인장하중하에서 토우부의 적정 요소 크기를 검토하고 여러 파라메타들의 값을 변화시켜 유한요소 응력해석을 수행하였다. 즉 용접토우부의 형상인 토우각 및 곡률반경의 영향과 용입부족부 길이의 변화를 동시에 고려한 응력집중계수를 정량적으로 구하였다. 그리고 그 결과를 이용하여 응력집중계수 추정식을 유도하였다.

• 대한기계학회논문집A
• /
• 제40권5호
• /
• pp.513-523
• /
• 2016

단순보와 외팔보의 U-노치 및 균열에 대한 응력집중계수 및 응력확대계수를 유한요소법 및 광탄성실험에 의해 해석하였다. 해석결과를 사용하여 응력집중계수 및 응력확대계수의 추정 그래프를 얻었다. 노치의 응력집중계수해석을 위하여 무차원 노치 길이 H(시편의 높이)/h=1.1~2, 무차원 틈 간격 r(노치선단의 반경)/h=0.1~0.5로 하였다. 여기서 h=H-c, c=노치길이이다. 해석결과 틈 길이가 증가할수록 그리고 틈 간격이 좁아질수록 응력집중계수는 증가 한다. 응력집중계수는 단순보가 외팔보다 더 크게 나타나나, 실제 일정한 하중과 노치길이 및 틈 간격 하에서 최대 응력값은 단순보보다 외팔보에서 크게 발생함을 알 수 있었다. 균열해석을 위하여 무차원 균열길이 a(균열길이)/H=0.2~0.5로 하였다. 균열의 길이가 증가 할수록 무차원 응력확대계수는 증가한다. 일정한 하중과 일정한 균열길이하에 응력확대계수값은 단순보 보다 외팔보에서 크게 발생함을 알 수 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 제7회 압연 심포지엄
• /
• pp.13-16
• /
• 2009

In order to investigate the effects of geometry factors such as a roil diameter ratio and backup roll crown of the stress concentration factor on the edge of backup roil end, 3-dimensional FEM analyses of stress at the contact of backup roll and work roll assembled in a 4-high strip mill were carried out, It was made clear that the peak stress at the edge is about 2 to 3 times of that at the longitudinal center of the roll barrel and the peak stress proportionally increase with decreasing the ratio of backup roll diameter to work roll diameter Furthermore a crowning on the backup roll is effective to decrease the maximum edge stress.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1810-1821
• /
• 1995

Photoelastic experiment has been used to analyze stress of structure and stress in the vicinity of crack tip etc.. Model experiment such as photoelastic experiment has been restricted by problem of residual stress in the photoelastic model material. They are generated by molding, cutting and time effects etc.. They produce some errors in the results of photoelastic experiment data. In this paper, stress optic law considering residual stress already developed by authors was applied to the stress concentration problem and fracture mechanics. Although the specimen was bad with residual stress, we could obtain good results by using the stress optic law considering residual stress. It was found that the stress optic law of photoelastic experiment could be applied to the stress analysis of bimaterial.

• 한국공작기계학회논문집
• /
• 제12권4호
• /
• pp.63-69
• /
• 2003

In discontinuous composite mechanics, shear lag theory is one of the most popular model because of its simplicity and accuracy. However, it does not provide sufficiently accurate strengthening predictions in elastic regime then the fiber aspect ratio is small. This is due to its neglect of stress transfer across the fiber ends and the stress concentrations that exist in the matrix regions near the fiber ends. To overcome this shortcoming, a more simplified shear lag model introducing the stress concentration factor which is a function of several variables, such as the modulus ratio, the fiber volume fraction, the fiber aspect ratio, is proposed. It is found that the modulus ratio($E_f$/$E_m$) is the essential variable among them. Thus, the stress concentration factor is expressed as a function of modulus ratio in the derivation. It is found that the proposed model gives a good agreement with finite element results and has the capability to correctly predict the values of interfacial shear stresses and local stress variations in the small fiber aspect ratio regime.

• 한국지반공학회논문집
• /
• 제18권5호
• /
• pp.133-141
• /
• 2002

암반파괴의 가장 큰 영향을 미치는 인장강도는 등방의 암석과 횡등방의 암석의 경우는 분명히 다를 것이다. 본 논문에서는 일축압축강도시험에서 횡등방 암석의 탄성정수를 구하고, 간접인장강도시험을 통하여 횡등방 암석의 인장강도와 인장파괴 거동을 분석하였다. 일축압축시험에서 구한 이방성 탄성정수와 간접인장강도시험에서 얻어진 변형률로 시료중앙의 응력집중계수를 구하여, 등방으로 가정하여 구한 인장강도 값과 이방성일때의 인장강도 값을 비교 분석하였다. 실험 결과 횡등방성 암석의 응력집중계수는 층리면의 각도에 따라서 등방재료의 응력집중계수와는 크거나 작은 값을 나타내었다. 횡등방 암석의 인장강도 산정시 등방의 응력집중계수를 사용하는 것은 층리면이 이루는 각도에 따라 인장강도의 과대 혹은 과소 평가됨을 알 수 있었다.