• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.67-73
• /
• 2021

Tanks are key weapons of ground combat that are equipped with powerful weapons and have strong protective bodies. One tank component, the engine clutch flange, is located in the part of the tank where the engine and transmission are installed, and it is a key part of the power transfer and shutoff. The engine clutch flange transmits high power to secure the mobility of the tank; thus, it must have high strength and hardness. In addition, high durability and safety must be ensured because tank operations must exclude concerns about damage. In this study, an engine clutch female flange for tanks made of SNCM439 was developed. The 2D design used AutoCAD programs, and the 3D shape design used CATIA programs. The structural analysis was conducted using ANSYS. The mesh grid has a tetrahedron shape and is created by adding a mid-side node. After the mechanical properties and constraints of SNCM439 were entered, the changes in the safety factor, total deformation, and Von-Mises stress were identified according to the increase in torque. Prototype processing was performed to verify the engine clutch female flange for the tank. To determine the productivity of the product, the cutting processing time was measured when processing the prototypes. Based on the results of measuring the cutting processing time, it is concluded that research is needed to improve productivity because MCT slot cutting processing is time consuming.

• Animal Bioscience
• /
• v.35 no.3
• /
• pp.475-483
• /
• 2022

Objective: Methionine (Met) is involved in methyl group transfer besides protein synthesis. As the availability is limited and cost is high for synthetic Met, reductions in its inclusion in broiler diet may be possible by supplementing the low Met diets with methyl donors (MD) like betaine (Bet), folic acid (FA), vitamin B12 (B12), and biotin (Bio). An experiment was conducted to study the effects of supplementing the MD on performance (average daily gain [ADG], daily feed intake, feed efficiency [FE]), anti-oxidant variables, immune responses and serum protein concentration in broilers fed sub-optimal concentrations of dietary Met. Methods: Maize-soybean meal diet was used as control (CD). Different MD like Bet (0.2%), B12 (0.1 mg), FA (4 mg), or Bio (1.5 mg/kg) were supplemented to basal diet (BD) having no supplemental Met. The BD without MD was kept for comparison. Each diet was fed ad libitum to 10 replicates of 25 chicks in each from 1 to 42 d of age. Results: At the end of experiment, the ADG in MD group was higher than BD and lower than CD. The FE improved with FA or Bet compared to the BD. Breast meat weight was higher in Bet compared to the BD, while it was intermediate between BD and CD in other groups. The lipid peroxidation reduced with Bio, B12, or Bet, while the glutathione peroxidase activity improved with Bio or B12 compared to the BD. Lymphocyte proliferation improved with Bet compared to the BD. The serum protein concentrations increased with FA, Bio, or Bet compared to those fed BD. Conclusion: It can be concluded that the ADG can be improved partially with supplementation of MD while the FE improved with FA or Bet. Some MD also reduced the stress indices and improved immune responses compared to the BD fed broilers.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.563-570
• /
• 2022

Industrialized and modular construction is a growing construction technique that can transfer a large portion of the construction process to off-site fabrication yards. This method of construction often involves the fabrication, pre-assembly, and transportation of massive and long volumetric modules. The module weight keeps increasing as the modules become more complete (with infill) to minimize the work at the site and, as higher productivity can be achieved at the fabrication shop. Thus, a volumetric module delivery gets more challenging and risky. Despite its importance, past research paid relatively insufficient attention to the problem related to the lifting of heavy modules. This can be a complex and time-consuming problem with multiple lifting for transportation-and-installation operations both in fabrication yard and jobsite, and require complex crane operations (sometimes, more than one crane) due to crane load capacity and load balance/stability. This study investigates this problem by focusing on the structural perspective of lifting such long volumetric modules through simulation studies. Various scenarios of lifting a weighty module from the top using four lifting cables attached to crane hooks (either a single crane or double crane) are simulated in SAP software. The simulations account for various factors pertaining to structural indices, e.g., bending stress and deflection, to identify a proper method of module lifting from a structural point of view. The method can identify differences in structural indices allowing identification of structural efficiency and safety levels during lifting, which further allows the selection of the number of cranes and location of lifting points.

• Structural Engineering and Mechanics
• /
• v.86 no.2
• /
• pp.261-276
• /
• 2023

The use of the ordinary double nut (i.e., ODN) composed of a master nut (i.e., M-nut) and a slave nut (i.e., S-nut) is a highly efficient method to prevent bolts loosening. A novel double nut (i.e., FODN) composed of a master nut (i.e., M-nut) and flat slave nut (i.e., FS-nut) is proposed to save raw materials. The bolt fastening tests with single nut, ODN and FODN are performed to investigate the preload and counterbalance forces. Corresponding finite element analysis (FEA) models are established and validated by comparing the preload with the experimental results. The load-bearing capacity, the extrusion effect, and the contact stress of each engaged thread for ODN and FODN are observed by FEA. The experimental and simulated results revealed that the bolt fastening with double-nut has different load-transferring mechanisms from single-nut. Nevertheless, for double-nut/bolt assemblies, the FS-nut can provide load transfer that is like that of the S-nut, and the FODN is a reasonable and reliable fastening method. Furthermore, based on the theory of Yamamoto, a formula considering the extrusion effect is proposed to calculate the preload distribution of the double-nut, which is applicable to varying thicknesses of slave-nuts in double-nut/bolt assemblies.

• Physical Therapy Rehabilitation Science
• /
• v.11 no.4
• /
• pp.493-501
• /
• 2022

Objective: The purpose of this study is to present basic data for appropriate therapeutic intervention by confirming changes in the autonomic nervous system and pain by applying high-frequency deep diathermy to the lower abdomen in patients with primary dysmenorrhea. Design: A randomized controlled clinical trial. Methods: Thirty-eight women aged 18-50 years who complained of regular menstrual cycles (24-32 days) and primary dysmenorrhea symptoms were randomly assigned to a high-frequency therapy group (5, 7, or 9 mins) and a superficial heat therapy group (20 min). High frequency treatment group: The subject was in a supine position, and radio frequency was applied to the lower abdomen below the umbilicus. The radio frequency therapy device used in this study uses a 300 kHz capacitive electrode and a 500 kHz resistive electric transfer to deliver deep heat. Superficial heat treatment Group: Subjects applied a hot pack to the lower abdomen for 20 minutes while lying on their back. Evaluations were made of Heart rate variability and Visual Analogue Scale. Results: In subjects with menstrual pain, there was a significant difference in pain between the high-frequency therapy group and the superficial heat therapy group (p=0.026). However, there was no significant difference between the autonomic nervous system and the stress resistance (p>0.05). Conclusions: As a result of this study, high-frequencytreatment using radiofrequency was effective in relieving pain because it can penetrate deeper tissues than conventional hot packs using superficial heat. In particular, it was found that the optimum effect was obtained when high frequency was applied forfive-seven minutes.

• Steel and Composite Structures
• /
• v.47 no.6
• /
• pp.709-728
• /
• 2023

Experimental and analytical studies were conducted to clarify the influencing mechanisms of the longitudinal reinforcement on performance of axially loaded Reinforced Concrete-Filled Steel Tube (R-CFST) short columns. The longitudinal reinforcement ratio was set as parameter, and 10 R-CFST specimens with five different ratios and three Concrete-Filled Steel Tube (CFST) specimens for comparison were prepared and tested. Based on the test results, the failure modes, load transfer responses, peak load, stiffness, yield to strength ratio, ductility, fracture toughness, composite efficiency and stress state of steel tube were theoretically analyzed. To further examine, analytical investigations were then performed, material model for concrete core was proposed and verified against the test, and thereafter 36 model specimens with four different wall-thickness of steel tube, coupling with nine reinforcement ratios, were simulated. Finally, considering the experimental and analytical results, the prediction equations for ultimate load bearing capacity of R-CFSTs were modified from the equations of CFSTs given in codes, and a new equation which embeds the effect of reinforcement was proposed, and equations were validated against experimental data. The results indicate that longitudinal reinforcement significantly impacts the behavior of R-CFST as steel tube does; the proposed analytical model is effective and reasonable; proper ratios of longitudinal reinforcement enable the R-CFSTs obtain better balance between the performance and the construction cost, and the range for the proper ratios is recommended between 1.0% and 3.0%, regardless of wall-thickness of steel tube; the proposed equation is recommended for more accurate and stable prediction of the strength of R-CFSTs.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.577-585
• /
• 2009

A 9-node degenerated shell finite element(FE), which has been developed for assessment of ultimate pressure capacity and nonlinear analysis for nuclear containment building is described in this paper. Reissner-Midnlin(RM) assumptions are adopted to develop the shell FE so that transverse shear deformation effects is considered. Material model for concrete prior to cracking is constructed based on the equivalent stress-equivalent strain relationship. Tension stiffening model, shear transfer mechanism and compressive strength reduction model are used to model the material behavior of concrete after cracking. Niwa and Aoyagi-Yamada failure criteria have been adapted to find initial cracking point in compression-tension and tension-tension region, respectively. Finally, the performance of the developed program is tested and demonstrated with several examples. From the numerical tests, the present results show a good agreement with experimental data or other numerical results.

• Composites Research
• /
• v.36 no.5
• /
• pp.315-320
• /
• 2023

In the manufacturing process of thermosetting carbon fiber composite materials using an autoclave, the internal temperature changes according to the set temperature cycle. This temperature change causes the resin in the composite material to cure. Heat is generated through the chemical reaction of the resin, which can result in a difference between the temperature inside the autoclave and the temperature of the composite material. Previous research assumed that the temperatures of the composite material and the autoclave were the same and analyzed to predict the residual stress and thermal deformation after manufacturing. However, these stresses and deformations depend on the temperature and degree of cure of the composite material. Therefore, this study verifies a thermal-chemical model analysis technique that takes into account the heat generated by the chemical reaction of the resin to accurately calculate the temperature and degree of cure. Additionally, case studies were conducted for different thicknesses to investigate whether this model exhibits similar trends across varying thicknesses.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1297-1303
• /
• 2023

Research on enhancing the mechanical strength, lightweight properties, electrical conductivity, and thermal conductivity of composite materials by incorporating nano-materials is actively underway. Thermoplastic resins can change their form under heat, making them highly processable and recyclable. In this study, Polyamide-Nylon 6 (PA6), a thermoplastic resin, was utilized, and as reinforcing agents, fused carbon nano-materials (FCN) formed by structurally combining Carbon Nanotube(CNT) and Graphene were employed. Nano-materials often face challenges related to cohesion and dispersion. To address this issue, Silane functional groups were introduced to enhance the dispersion of FCN in PA6. The manufacturing conditions for the composite materials involved determining the use of a dispersant and varying FCN content at 0.05 wt%, 0.1 wt%, and 0.2 wt%. Tensile strength measurements were conducted, and FE-SEM analysis was performed on fracture surfaces. As a result of the tensile strength test, it was confirmed that compared to pure PA6, the strength of the polymer composite with a content of 0.05 wt% was improved by about 60%, for 0.1 wt%, about 65%, and for 0.2 wt%, the strength was improved by 50%. Also, when compared according to the content of FCN, the best strength value was shown when 0.1 wt% was added. The elastic modulus also showed an improvement of about 15% in the case of surface treatment compared to the case without surface treatment, and an improvement of about 70% compared to pure PA6. Through FE-SEM, it was confirmed that the matrix material and silane-modified nanomaterial improved the dispersibility and bonding strength of the interface, helping to support the load evenly and enabling effective stress transfer.

• Journal of Embryo Transfer
• /
• v.22 no.3
• /
• pp.161-165
• /
• 2007

Oxytocin is a neurohypophyseal hormone which has multiple functions in mammals. Mainly, oxytocin regulates milk ejection and has an effect on uterine contraction and is related to maternal behavior. Maternal behavior is believed to be suppressed by stress and facilitated by oxytocin. In the cesarean section, oxytocin may be administrated into uterus to promote uterine involution. The present study aimed to test the effect of oxytocin into uterus on maternal behavior of rats with cesarean section. It was measured the effects on maternal behavior of oxytocin infused into uterus in rats with cesarean section as a stressor. In the first experiment, pup survival rate of between a control group and a group with laparotomy as a stress in natural parturition rats was compared. In the second experiment, survival rate for 2 weeks and maternal pup searching behavior (MPSV) were observed in one cesarean sectioned group without oxytocin and the other cesarean sectioned group with oxytocin. Infanticide was observed in stressed group in the first experiment while a normal maternal behavior was observed in a control one. In the second experiment, MPSV was only observed in a cesarean sectioned group with oxytocin and infanticide was observed in two groups except one rat which is thought to be affected by oxytocin as operated relatively late. This is the first study to show that the administration of oxytocin into uterus in the cesarean section is not involved in the regulation of maternal behavior in rats. In conclusion, this study proves the needs of oxytocin into brain in cesarean section related rats model and further study of maternal behavior list, like MPSV.