• Magazine of korean Tunnelling and Underground Space Association
• /
• v.1 no.1
• /
• pp.81-87
• /
• 1999

Effects of blasting vibrations on curing concrete have not been well studied. As a result, unrealistic and costly blasting vibration constraints have been placed on blasting when it occurs in the vicinity of curing concrete. To study the effects of blasting, concrete blocks of $30\times20\times20cm$ were molded and placed on the quarry Different sets of concrete blocks were subjected to peak vibrations of 0.25, 0.5, 1.0, 5.0, and 10cm/sec. The impulses of blasting vibrations were applied at thirty minutes intervals . Along with unvibrated concrete blocks, the vibrated concrete samples with 60.3mm in diameters were measured for elastic moduli, sonic velocity and uniaxial compressive strength. Test results can be summarized as follows : 1) The blasting vibrations between 6 and 8 hours after pour generally have exerted bad influences on the uniaxial compressive strength of the concrete 2) Under low vibration of 0.25cm/sec variations of the uniaxial compressive strength were not shown. As the magnitudes of blasting vibration increased, compressive strength of concrete decreased. But under the vibrations between 5 and 10cm/sec decreases in strength were almost same. 3) Physical properties of the p-wave velocity, Young's modulus, and Poisson's ratio appeared to decrease for the concrete blocks subjected to vibration for 6 to 8 hours.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.168-173
• /
• 2004

Fretting is a kind of surface degradation mechanism observed in mechanical components and structures. The fretting damage decrease in 50-70% of the plain fatigue strength. This may be observed in aircraft, automobile and nuclear power plant used in special environment and various loading conditions. In the present study, the characteristics of the fretting fatigue are investigated using the two aluminum alloy(Al2024-T3511 and Al7050-T7451). Through the experiment, it is found that the fretting fatigue strength of the Al7050-T7451 alloy decreased about 50% from the plain fatigue strength, while the fretting fatigue strength of the Al2024-T3511 alloy decreased about 45%. The tire track was widely observed in fracture surface area of oblique crack which was induced by contact pressure. These results can be the basic data to the structural integrity evaluation of aluminum alloy subjected to fretting damage.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.99-106
• /
• 2008

Through mechanical alloying, hot isostatic pressing and hot rolling, a 9%Cr Fe-based oxide dispersion-strengthened alloy sample was fabricated. The tensile strength of the alloy is significantly improved when the microstructure is modified during the post-consolidation process. The alloy samples were strengthened as the cooling rates increased, though the elongation was somewhat reduced. With a cooling rate of $800^{\circ}C/s$ after normalization at $1150^{\circ}C$, the alloy sample showed a tensile strength of 1450 MPa, which is about twice that of the hot rolled sample; however, at $600^{\circ}C$ the tensile strength dramatically decreased to 620 MPa. Optical microscope and transmission electron microscope were used to investigate the microstructural changes of the specimens. The resultant strengthening of the alloy sample could be mainly attributed to the interstitially dissolved nitrogen, the fraction of the tempered martensite, the fine grain and the presence of a smaller precipitate. The decrease in the tensile strength was mainly caused by the precipitation of vanadium-rich nitride.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.171-176
• /
• 2007

An important challenging issue in the automotive industry is the light-weight, safe design and enhancement of crash response of an auto-body structures. These objectives lead to increasing adoption of high strength steel sheet for inner and outer auto-body members. This paper evaluates the dynamic tensile characteristics of high strength steel sheets, HS45R, TRIP60, DP60 and DP100, along the rolling direction and transverse direction. Static tensile tests were carried out at the strain rate of 0.003/sec using the static tensile machine (Instron 5583). Dynamic tensile tests were carried out at the range of strain rate from 0.1/sec to 200/sec using a high speed material testing machine developed. The tensile tests acquire stress-strain relation and strain rate sensitivity of each material. The experimental results show two important aspects for high strength steels: the flow stress increases as strain rate increases; the strain hardening decreases as the tensile stress increases. The experiments also produce interesting results that the elongation does not decrease even when the strain rate increases.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.1-8
• /
• 2006

In this study, effect of sputtering after plasma nitriding and before PVD coating on the microstucture, microhardness, surface roughness and the adhesion strength of CrN thin films were investigated. Experimental results showed that this sputtering process not only removed surface compound layer which formed during a plasma nitriding process but also induced an alteration of the surface of plasma nitrided substrate in terms of microhardness distribution and surface roughness, which in turn affected the adhesion strength of PVD coatings. After sputtering, microhardness distribution showed general decrease and the surface roughness became increased slightly. The critical shear stress measured from the scratch test on the CrN coatings showed an approximately twice increase in the binding strength through the sputtering prior to the coating and this could be attributed to a complete removal of compound layer from the plasma nitrided surface and to an increase in the surface roughness after sputtering.

• Structural Engineering and Mechanics
• /
• v.72 no.3
• /
• pp.367-382
• /
• 2019

This paper presents experimental and analytical investigations on additional fixed-end rotations resulting from the strain penetration of high-strength reinforcement in reinforced concrete (RC) beam-column connections under monotonic loading. The experimental part included the test of 18 interior beam-column connections with straight long steel bars and 24 exterior beam-column connections with hooked and headed steel bars. Rebar strains along the anchorage length were recorded at the yielding and ultimate states. Furthermore, a numerical program was developed to study the effect of strain penetration in beam-column connections. The numerical results showed good agreement with the test results. Finally, 87 simulated specimens were designed with various parameters based on the test specimens. The effect of concrete compressive strength ($f_c$), yield strength ($f_y$), diameter ($d_b$), and anchorage length ($l_{ah}$) of the reinforcement in the beam-column connection was examined through a parametric study. The results indicated that additional fixed-end rotations increased with a decrease in $f_c$ and an increase in $f_y$, $d_b$ and $l_{ah}$. Moreover, the growth rate of additional fixed-end rotations at the yielding state was faster than that at the ultimate state when high-strength steel bars were used.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.3
• /
• pp.199-203
• /
• 2019

The penetration depth of a hypervelocity jet exceeding 4 km/s is described by the density ratio of the jet and the target. In the case of the same density, the difference in strength between the targets does not affect the penetration depth difference. This study focuses on the "strength irrelevance" of such a hypervelocity jet. For this purpose, the change of crater pressure caused by shaped charge jet(SCJ) was calculated by finite element analysis and the possibility of polymorphic phase transition of steel material was investigated. Hypervelocity jets were found to cause polymorphic phase transitions in the steel target craters, and the decrease in the fracture toughness of the target is predicted as the cause of the strength irrelevance.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.27 no.1
• /
• pp.13-20
• /
• 2021

Background: The serratus anterior and upper trapezius muscles act synergistically to allow for an appropriate scapulothoracic rhythm. However, a decrease in serratus anterior activation causes the upper trapezius to become overactivated, resulting in dysfunction. This study compared serratus anterior and upper trapezius muscle activity according to sling angle and compared serratus anterior strength between healthy adults and patients with shoulder instability. Methods: Twenty participants (10 healthy adults and 10 patients with shoulder instability) were included in this study. The participants had their arms extended at sling angles of 30°, 60°, and 90° in reach forward with shoulder flexion using goniometer. Serratus anterior strength was measured three times while the participants were supine. The outcome measures were surface electromyography amplitude of the upper trapezius and serratus anterior and serratus anterior strength. Results: The Wilcoxon signed-rank test indicated that the upper trapezius was significantly different between healthy group and shoulder instability group at a sling angle of 60°, and both the upper trapezius and serratus anterior exhibited significant differences at 90°. Moreover, a significant difference was noted in the muscle strength of the serratus anterior. Conclusion: Our results provide novel and promising clinical evidence that patients with shoulder instability have decreased serratus anterior activation and upper trapezius overactivation, resulting in muscle imbalance. In addition, there was a significant difference between the healthy group and shoulder instability group in the serratus anterior muscle strength

• Korean Journal of Metals and Materials
• /
• v.47 no.3
• /
• pp.195-201
• /
• 2009

This paper is concerned with effects of Mn and heat-input on the mechanical properties of EGW welds. Four different kinds of welding consumables were fabricated by varying Mn contents such as 1.3, 1.5, 1.7, 2.0%Mn and each consumable was welded for EGW on four heat-input conditions between 190 and 340 KJ/Cm. Mn contents were decreased as heat-input increases and alloy elements (C, Si, Ti, B, Al) to deoxidize easily also revealed similar tendency to Mn. Their microstructure, Charpy impact property and strength were investigated, and it is found that Charpy impact property and strength exhibit a strong dependence on change of microstructure by Mn contents and heat-input. The increase of Mn contents or the decrease of heat-input made the microstructure fine and increase volume fraction of acicular ferrite, thereby leading to the great improvement of Charpy impact property and strength. In case of single EGW, optimum Mn contents are over 1.7% for the toughness and strength.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.26 no.2
• /
• pp.19-27
• /
• 2020

Background: The purpose of this study was to examine the effects of a multi-modal exercise program for patients with chronic low back with respect to pain intensity, trunk muscle strength and Oswestry disability index. Methods: Thirty patients with chronic low back pain were recruited and divided equally into two groups. The multi-modal training program comprised a series of exercises such as warm-up, stabilization exercises, stretching, endurance exercises, and cool down whereas the control group performed only stabilization exercises. The both group spent an equal amount of time performing 60 minutes per day, three times per week, for five weeks. Results: The experimental group demonstrated statistically significant improvements in range of motion, trunk muscle strength, the visual analogue scale, and the Oswestry Disability Index (p<.05). Intergroup comparison showed a statistically significant difference in the range of motion of the lumbar spine and the degree of disability in the experimental group. Muscle strength and pain were statistically significant in both groups. Conclusion: The multi-modal exercise program is effective for patients with chronic low back pain, as it reduces lower back pain, increases trunk muscles strength, and decrease the potential for becoming disabled.