• Transactions on Electrical and Electronic Materials
• /
• 제12권1호
• /
• pp.28-31
• /
• 2011

Transformation behavior and shape memory characteristics of Ti-(45-x)Ni-5Cu-xCr (x=0.5-2.0) alloys have been investigated by means of electrical resistivity measurements, differential scanning calorimetry, X-ray diffraction and thermal cycling tests under constant load. Two-stage B2-B19-B19' transformation occurred in Ti-(45-x)Ni-5Cu-xCr alloys. The B2-B19 transformation was separated clearly from the B19-B19' transformation in Ti-44.0Ni-5Cu-1.0Cr and Ti-43.5Ni-5Cu-1.5Cr alloys. A temperature range where the B19 martensite exists was expanded with increasing Cr content because decreasing rate of Ms (85 K / % Cr) was larger than that of Ms' (17 K / % Cr). Ti-(45-x)Ni-5Cu-xCr alloys were deformed in plastic manner with a fracture strain of 68% ~ 43% depending on Cr content. Substitution of Cr for Ni improves the critical stress for slip deformation in a Ti-45Ni-5Cu alloy due to solid solution hardening.

• 한국강구조학회 논문집
• /
• 제23권4호
• /
• pp.405-415
• /
• 2011

건축물의 안전한 내진설계를 위해서는 층간변위비 뿐만 아니라 부재에 요구되는 소성변형을 평가하여야 한다. 본 연구에서는 복잡한 비선형해석 없이 탄성해석을 사용하여 강기둥-약보로 설계된 철골 특수모멘트골조의 보에 요구되는 소성변형을 평가하는 간편한 방법을 개발하였다. 개발한 방법은 탄성해석 결과를 근거로 모멘트 재분배, 기둥 단면치수 및 보 소성힌지 이동, 패널존 변형, 중력하중, 변형경화 거동 등을 고려하여 보의 소성변형각을 직접적으로 예측한다. 또한 가새골조 또는 코어벽 등 횡력 저항구조와 모멘트골조의 상호 작용인 로킹 효과 고려한다. 검증을 위하여 강기둥-약보로 설계된 6층 특수모멘트골조에 제안된 방법을 적용하여 보의 소성변형각을 예측하고, 그 결과를 비선형 해석 결과와 비교하였다. 검증 결과, 제안된 방법은 설계 변수에 따른 보의 소성변형각을 합리적으로 예측하는 것으로 나타났다.

• 한국지반신소재학회논문집
• /
• 제18권2호
• /
• pp.11-21
• /
• 2019

본 연구에서는 말뚝의 인발저항에 대한 합리적 평가를 위하여, 다양한 지반 조건(상대밀도, 세립분 함유율)에서 말뚝의 인발거동 모사에 대한 유한요소해석의 적용성을 평가하였다. 즉, 기존의 실내모형실험 결과(You et al., 2018)를 대상으로 동일한 조건에서의 유한요소해석을 실시하였고, 유한요소해석에 이용된 해석모델의 신뢰성을 검증하였다. 또한 수치해석을 활용한 말뚝의 인발거동 모사에 대한 적정성을 평가하였다. 그 결과, 가상지반이 적용된 축대칭 해석을 이용하여 말뚝의 주면마찰력을 평가할 수 있는 것으로 확인되었다. 또한 다양한 지반 조건에 대하여 말뚝-지반 경계면의 전단저항 특성을 반영할 수 있는 축대칭 해석은 말뚝의 합리적인 인발거동 모사가 가능한 해석방법으로 활용이 가능한 것으로 분석되었다. 따라서 본 연구를 통하여 제안된 해석모델은 말뚝의 응력-변형 관계를 통한 인발거동을 적절하게 모사할 수 있는 것으로 판단되었다.

• 대한기계학회논문집A
• /
• 제39권4호
• /
• pp.383-390
• /
• 2015

본 논문에서는 원전 배관 재료의 변형거동에 미치는 하중속도의 영향을 파악하기 위해서, SA508 Gr.1a 저합금강과 SA312 TP316 스테인리스강 배관재를 대상으로 상온과 원전 운전온도인 $316^{\circ}C$에서 다양한 변형률 속도로 인장시험을 수행하였다. 시험 결과, 상온에서는 두 배관재의 변형거동이 일반적인 하중속도 의존성을 보였다. 즉, 하중속도가 증가함에 따라 강도는 증가하고 연성은 감소하는 경향을 보였다. 그러나, $316^{\circ}C$에서는 하중속도가 증가함에 따라 SA508 Gr.1a 저합금강의 강도와 연신률이 모두 감소하였고 단면수축률은 감소 후 증가하는 비선형 거동을 보였다. SA312 TP316 스테인리스강의 강도, 연신률, 그리고 단면수축률은 하중속도에 관계없이 거의 일정한 값을 보였다. 시험 온도에 관계없이 SA508 Gr.1a 저합금강의 가공경화능력은 하중속도에 거의 영향을 받지 않았으나, SA312 TP316 스테인리스강에서는 하중속도가 증가함에 따라 가공경화능력이 감소하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.421-424
• /
• 2007

Dry sliding wear behavior of ultra-fine grained (UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• Tribology and Lubricants
• /
• 제28권1호
• /
• pp.19-26
• /
• 2012

Rolling contact fatigue of an urban railway wheel was analysed during its rolling. A FEM analysis was performed using a 3D modelling of rail and wheel, considering the slope of the rail and nonlinear isotropic and kinematic hardening behavior of the rail and the wheel. The maximum von-Mises stress and contact pressure between the rail and wheel were 656.9 MPa and 1111.4 MPa, respectively, under axial load of 85 kN with friction coefficient of 0. The fatigue initiation life prediction relationships by strain-lifetime (${\varepsilon}$-N) and Smith-Watson-Topper method were drawn for the wheel steel as follows: $N_i=7.35{\times}10^6{\times}SWT^{-3.56}$ and $N_i=5.41{\times}10^{-9}{\times}(\frac{{\Delta}{\varepsilon}}{2})^{-5.77}$. The fatigue lifetimes of the wheel due to rolling contact were determined to be infinite by ${\varepsilon}$-N and SWT methods.

• Structural Engineering and Mechanics
• /
• 제38권4호
• /
• pp.385-403
• /
• 2011

Continuous deep girders which transmit the gravity load from the upper wall to the lower columns have frequently long end shear spans between the boundary of the upper wall and the face of the lower column. This paper presents the results of tests and analyses performed on three 1:2.5 scale specimens with long end shear spans, (the ratios of shear-span/total depth: 1.8 < a/h < 2.5): one designed by the conventional approach using the beam theory and two by the strut-and-tie approach. The conclusions are as follows: (1) the yielding strength of the continuous RC deep girders is controlled by the tensile yielding of the bottom longitudinal reinforcements, being much larger than the nominal strength predicted by using the section analysis of the girder section only or using the strut-and-tie model based on elastic-analysis stress distribution. (2) The ultimate strengths are 22% to 26% larger than the yielding strength. This additional strength derives from the strain hardening of yielded reinforcements and the shear resistance due to continuity with the adjacent span. (3) The pattern of shear force flow and failure mode in shear zone varies depending on the amount of vertical shear reinforcement. And (4) it is necessary to take into account the existence of the upper wall in the analysis and design of the deep continuous transfer girders that support the upper wall with a long end shear span.

• Geomechanics and Engineering
• /
• 제20권4호
• /
• pp.359-370
• /
• 2020

Prestressed ground anchors are important structural elements in geotechnical engineering. Despite their widespread usage, the design process is often significantly simplified. One of the major drawbacks of commonly used design methods is the assumption that skin friction is mobilized uniformly along an anchor's fixed length, one consequence of which is that a progressive failure phenomenon is neglected. The following paper introduces an alternative design approach - a computer algorithm employing the load-transfer method. The method is modified for the analysis of anchors and combined with a procedure for the derivation of load-transfer functions based on commonly available laboratory tests. The load-transfer function is divided into a pre-failure (hardening) and a post-failure (softening) segment. In this way, an aspect of non-linear stress-strain soil behavior is incorporated into the algorithm. The influence of post-grouting in terms of radial stress update, diameter enlargement, and grout consolidation is included. The axial stiffness of the anchor body is not held constant. Instead, it gradually decreases as a direct consequence of tensile cracks spreading in the grout material. An analysis of the program's operation is performed via a series of parametric studies in which the influence of governing parameters is investigated. Finally, two case studies concerning three investigation anchor load tests are presented.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.1-10
• /
• 2020

This study proposed a simulated test method using ring specimen to evaluate the deformation and failure characteristics of pipe elbows under a large amplitude cyclic load. The validity of the test method was demonstrated by finite element (FE) analysis of pipe elbow and ring specimen under cyclic loads. The results showed that the proposed test method adequately simulates the distribution of circumferential strain at crown of pipe elbows where cracks occur under cyclic loads and presents the cyclic hardening behavior of pipe elbows. The parametric FE analysis showed that consistent simulated test results could be obtained when the test section of the ring specimen is longer than 1/2 of the inner diameter of the ring specimen and the radius of the inner loading jig is less than 1/4 of the inner diameter of the specimen.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.21-22
• /
• 2009

본 논문에서는 SHCC로 단면 복구된 콘크리트 보가 동결융해 환경에 노출되는 경우 그 휨 보강 및 균열제어 특성에 대한 실험결과를 제시한다. 본 연구에서 사용된 SHCC는 PVA 및 PE 섬유를 각각 0.75% 보강한 것이며 물결합재 비를 주요변수로 한다. 실험결과 SHCC로 휨 인장측이 단면 복구된 콘크리트의 휨내력은 동결융해의 노출 유무에 따라 각각 2.42 및 3.31배 증가되었다. 또한 휨 인장측의 균열제어 성능도 우수하게 나타났으나 이러한 성능은 동결융해에 노출됨에 따라 저하되는 특성을 보였다. 이는 시멘트 복합체와 섬유계면이 반복 동결융해에 의해 손상되었기 때문인 것으로 판단된다.