• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.353-354
• /
• 2009

Tensile deformation behavior with different strain rate was investigated. $Zr_{56.2}Ti_{13.8}Nb_{5.0}Cu_{6.9}Ni_{5.6}Be_{12.5}$ (bulk metallic glass alloy possessed crystal phase which was called $\beta$-phase of dendrite shape, mean size of $20{\sim}30{\mu}m$ and occupied 25% of the total volume) was used in this study. Maximum tensile strength was obtained as 1.74Gpa at strain rate of $10^2/s$ and minimum strength was found to be 1.6GPa at $10^{-1}/s$. And then, maximum plastic deformation occurred at the strain rate of $5{\times}10^{-2}/s$ and represented 1.75%, though minimum plastic deformation showed 0%. In the specific range of strain rate, relatively higher plastic deformation and lower ultimate tensile strength were found with lots of shear bands. The fractographical observation after tensile test indicated that vein like pattern on the fracture surface was well developed especially in the above range of strain rate.

• Corrosion Science and Technology
• /
• v.23 no.2
• /
• pp.113-120
• /
• 2024

An attempt was made to apply digital image correlation (DIC) strain analysis to in-situ scanning electron microscopy (SEM) observations of bending deformation to quantify local strain distribution inside a ZnMgAl-alloy coating in deformation. Interstitial-free steel sheets were hot-dipped in a Zn-3Mg-6Al (mass%) alloy melt at 400 ℃ for 2 s. The specimens were deformed using a miniature-sized 4-point bending test machine inside the SEM chamber. The observed in situ SEM images were used for DIC strain analysis. The hot-dip ZnMgAl-alloy coating exhibited a solidification microstructure composed of a three-phase eutectic of fine Al (fcc), Zn (hcp), and Zn2Mg phases surrounding the primary solidified Al phases. The relatively coarsened Zn₂Mg phases were locally observed inside the ZnMgAl-alloy coating. The DIC strain analysis revealed that the strain was localized in the primary solidified Al phases and fine eutectic microstructure around the Zn₂Mg phase. The results indicated high deformability of the multi-phase microstructure of the ZnMgAl-alloy coating.

• Journal of radiological science and technology
• /
• v.47 no.4
• /
• pp.279-286
• /
• 2024

Echocardiography is a widely used test to evaluate the contractility of the heart. However, this exam is cannot be said to be objective because the test relies on the examiner's visual judgment. Therefore, although a lot of efforts are being made to quantify the strain through speckle tracking echocardiography (STE), there are some limitations, and studies of conditions to supplement are needed. Through this study, we determine whether the general characteristics of the subjects affect vessel-specific strain and whether changes in various imaging conditions (general, resolution, compression, gain, chroma) affect vessel-specific strain. According to the results of the study, the general conditions obtained during the examination were generally less significant compared to other conversion conditions, and Resolution, Compress, Gain, Chroma, and LAD showed significant correlations under the Compress conditions (p < .05). Therefore, Accurate strain assessment will be made if echocardiography is analyzed using significant conditions for each stenotic vessel

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1192-1202
• /
• 1994

Fatigue behavior and life prediction were presented for thermal-mechanical and isothermal low cycle fatigue of 12Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test at 350 to 600.deg. C and isothermal low cycle fatigue test at 600.deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. Cyclic softening behavior was observed regardless of thermal-mechanical and isothermal fatigue tests. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. The difference in fatigue lives was dependent upon the magnitudes of inelastic strain ranges and mean stresses. Increase in inelastic strain range showed a tendency of intergranular cracking and decrease in fatigue life, especially for out-of-phase thermal-mechanical fatigue. Thermal-mechanical fatigue life prediction was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase thermal-mechanical fatigue lives, which was quite improved conservatively by a proposed strain range partitioning method.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.17-25
• /
• 2012

FEM requires the stress-strain relationship equations for numerical analyses. However, most formulations for the stress-strain relationship published up to the present are not satisfactory enough to properly express all the levels from the small strain to the peak. Tatsuoka and Shibuya (1991) suggested a new single formulation applicable not only to a wide range of geo-materials from soft clay to soft rock, but also to a wide range of strain levels from $10^{-6}$ to $10^{-2}$. The plain strain compression test is carried out to seven samples of research standard sand specimens and two samples of glass beads, which have been used at world-renowned research institutes. In this study, strains of the maximum principal stress (${\sigma}_1$) and the minimum principal stress (${\sigma}_3$) were thoroughly measured from $10^{-6}$ to $10^{-2}$, and the result, applied to Tatsuoka and Shibuya's new formulation, coincided closely with the measured data of the stress-strain relationship from the small strain to the peak.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.67-74
• /
• 2014

In this study, a constant rate of strain test (CRS) and oedometer test was performed in order to study the consolidation characteristics to the liquid limit using a re-shaped clay which was preconsolidated at a constant pressure. Consolidation samples were made of kaolinite which was mixed with bentonite of 6 %, 9 %, 12 % and 15 % of it by weight and the test value of liquid limit of samples were appeared in 77 %, 84 %, 88 % and 91 % respectively. And then consolidation samples which were agitated sufficiently adding distilled water 2 times of liquid limit were preconsolidated in the condition of a constant pressure of 0.2 MPa. The oedometer test which is commonly used recently and the consolidation test of constant rate of strain which were applied in 0.001 %/min, 0.004 %/min, 0.01 %/min rate of strain according to ASTM, D4186-82 were performed and the preconsolidation pressures were compared and analyzed at 0.2 MPa preconsolidated pressure. As a result, in the case of low value of liquid limit, preconsolidation pressure was appeared same as 0.2 MPa preconsolidated pressure at the high speed strain rate, and in the case of high value of liquid limit, preconsolidation pressure was appeared same as 0.2 MPa preconsolidated pressure at the low speed strain rate.

• Journal of the Korean Society of Safety
• /
• v.37 no.5
• /
• pp.7-13
• /
• 2022

Digital image correlation (DIC) is a method used to measure the displacement and strain of structures. It involves transforming and analyzing images before and after deformation using correlation coefficients from irregular light and shade on the surface of structures. In the present study, a microspeckle pattern was applied to the surface of a specimen to identify initial cracking. The test specimen constituted CFRP composites laminated on a curved Al liner The specimen was manufactured by stacking 100 ply of CFRP prepregs in the 0° and 90° directions in a three-point bending test. The equivalent strain was evaluated through DIC analysis after monitoring deformation using a CCD camera. Fracture shape was observed using a microscope. The equivalent strain contour distribution was checked until the maximum load fracture occurred at the center of the test specimen. Variations in the strain indicated the initial occurrence and progression of microcracks. These results can be used to improve the accuracy of detecting micro crack initiation and to achieve structural stability.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.11
• /
• pp.39-46
• /
• 2010

The magnitude of the lateral resistance that resists the lateral movement of the pile is controlled by the amount of the pile movement and the strength and stiffness of soil. In this paper, we proposed an equation which produces the lateral resistance of the laterally loaded single pile using the strain wedge model of the soil deformation. The results of this equation is compared with results of model test, field test, p-y curve and other methods. It is found that the result of proposed equation is smaller than the result of model test. The results of loading test considerably coincide with those of proposed equation; however, a few of deviations are generated as the displacement of pile head increases. Moreover, coincidences exist between the results of the proposed equation and those of finite difference method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.6
• /
• pp.617-622
• /
• 2012

Structures are often subjected to various types of loading such as static, dynamic, or impact loading. Therefore, experimental and numerical methods have been employed to find adequate material properties according to the conditions. The Split-Hopkinson pressure bar (SHPB) test has frequently been used to test engineering materials, particularly those used under high strain rates. In this study, the compressive deformation behaviors of aluminum alloy under impact conditions have been investigated by means of the SHPB test. The experimental results were then compared with those of finite element analyses. It was shown that reasonably good agreement with the true stress-strain curves was obtained at strain rates ranging from 1000 $s^{-1}$ to 2000 $s^{-1}$. When the strain rate increased by 30%, the peak stress in particular increased by 17%, and the strain also increased by 20%.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.199-210
• /
• 2003

The development of strain localization within shear zones is frequently observed during soil deformation. In fact, the phenomenon appears to be more often the norm rather than the exception. Conceptually, any soil condition that renders negative work increment is prone to localization. In this study, a broad range of soil and loading conditions are investigated to test this criterion, including: dilative soil subjected to drained shear (standard case), contractive soil sheared under undrained conditions, cavitation in dilative soil in undrained shear, inhomogeneous soils, particle alignment in contractive soils made of platy particles, soils that experience particle crushing, and the shear of low-moisture and/or lightly cemented loose soils. Unique specimens and test procedures are designed to separately test each of these soil conditions in the laboratory According to experimental test results, soil specimens with post-peak strain softening behavior are prone to progressive failure, localization of deformations, and shear banding. The state of stress, the soil density, inherent mechanical and geometrical properties of soil particles, low water content, and heterogeneity can contribute to triggering strain localization. Considering all possible cases of localization, the best method to obtain the critical state line in the laboratory is to use contractive homogeneous specimens subjected to drained shear.