• Transactions of the Society of Information Storage Systems
• /
• v.10 no.1
• /
• pp.19-22
• /
• 2014

Optical nonlinear property is utilized to the wave generation, generating the beam at intended wavelength, and optical computing systems. The genetic material, which is the DNA with helical structure in nano-scale, is fascinating for optics communities due to artificially controllable sequence that determines the physical and chemical property. Nonlinearity of DNA was investigated by the four wave mixing experiment, which is with two incident beams located at 1550nm and 1650nm. The four output beams including incident beams are emitted from genetic material such as 1461nm and 1763nm by nonlinear characteristic. The 1461nm beam which is generated by four wave mixing phenomena was observed by optical spectrum analyzer.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.89-95
• /
• 2009

We setup the system to measure the noise characteristics of the 5M complementary metal-oxide semiconductor (CMOS) image sensor by generic measurement indicator of Standard mobile imaging architecture (SMIA) which is one of internal standard of mobile imaging architecture. To evaluate the effect of environment and setting parameters, such as temperature and integration time, we measure the variation of the dark signal, dynamic range and fixed pattern noise of image sensor. We also detect the number of defective pixels and cluster defects defined as adjacent single defect pixels at 5M CMOS image sensor. Then, we find the existence of some cluster defects in experiment, which are not expected in calculation.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.1
• /
• pp.14-18
• /
• 2009

This paper proposed an optimal plate spring design for the optical image stabilizer in mobile phones. The voice-coil motor (VCM) with plate spring is the smallest, lowest-cost solution for auto focus on the market today and it is also the simplest to implement. The VCM is selected in this paper for auto focusing. However, the design process is complex due to the many design variables coupled to each other and some constraints of each directional motion caused by the characteristics of plate spring. Because of the complex formulation of the design objective, a plate spring design is proposed through the design of experiments to find the optimal design satisfying design constraints.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.11
• /
• pp.572-576
• /
• 2003

For quite a long time various researches and developments of superconducting magnetic energy storage(SMES) device have been done for enhancement of power qualify control of sensitive electric load. This paper describes the design. fabrication and experimental results for the 3MJ SMES magnet made by using the design code of a SMES device that we developed. A computer code was developed to find the parameters of the SMES magnet which has minimum amount of superconductor for the same stored energy, and the 3MJ SMES magnet was designed based upon that. And the 3MJ SMES magnet designed based upon those. In addition, 3MJ SMES magnet was made based on several research results which were ramp up to 1㎄ without quench.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.2
• /
• pp.65-69
• /
• 2011

Head Disk Interface (HDI) in a Hard Disk Drive (HDD) has decreased to achieve high areal density. Thus, the contact between a slider and a disk becomes more important. The contact between the slider and the disk can cause severe wear and damage of both the slider and the disk. Especially, Touch Down (TD) that the contact occurs continuously and repeatedly is extremely dangerous. Therefore, it is necessary to analyze the unstable bouncing vibration of the slider in head-disk interface. In this paper, we investigate the characteristic and causes of the Touch Down.

• YAKHAK HOEJI
• /
• v.21 no.2
• /
• pp.101-109
• /
• 1977

The effect of humidity on the aging process of hydrous aluminum oxide prepared by the reaction of aluminum chloride and sodium bicarbonate solution at pH 7.8, which was then kept in various atmosphere under relative humidity at 37.deg. was observed by the measurements of acid consuming capacity, X-ray diffraction and IR absorption. The humidity was one of the important factors influencing the aging process of hydrous aluminum oxide during storage. The higer the humidity, the more was accelerated age, crystalize and loss in acid reactivity. Depending on the humidity, the aging product was different, especially, in the case of up to the relative humidity of 72%, it forming bayerite. On the other hand, the hydrous aluminum oxide aged below the relative humidity of 50% was still amorphous even after 120 days storage. When hydrous aluminum oxide was aged under higher humidity, definite IR absorption bands develop as the hydroxys become part of an ordered structure, and it showed their characteristic absorption band around 1630 and 1060 cm$^{-1}$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.4
• /
• pp.41-46
• /
• 1983

The current-fed DC-DC converter has only one energy storage reactor in series with the input for any number of outputs and is insensitive to transformer volt-second unbalance. It is considered that these properties of the converter are considerable advantages over other maltiple-output circuits. The steady-state and dynamic characteristic and stability for the current-fed DC-DC con-verter are analyzed in detail. The analysis is carried out by the state-space averaging method for the operation with the duty ratio less than 50% and is confirmed by the experiment. From the evaluation of stability it is identified that the stability of this converter is excellent as compared with that of the conventional buck type converter.

• Journal of Industrial Technology
• /
• v.18
• /
• pp.453-460
• /
• 1998

The purpose of this study was to analyze their status of underground storage tank(UST) facilities and level of soil contamination, and to establish its management criteria. DB program was developed to analyze the correlation between specific characteristic of UST and level of soil contamination. For a suitable management of UST, leakage monitoring and inspection method of UST was investigated. Inspection period was established based on the leakage rate. The most dominant factor for leakage seemed to be caused by the corrosion. Therefore, main factor, construction method and installation year of UST, and corrosion protection system were suggested for optimal protection of UST. Considering the present management status of UST in Korea, inspection and management criteria of UST should be accomplished in term of contamination protection of leakage, and flexible regulation act should be introduced for each specific site.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.58-62
• /
• 2001

Photovoltaic and wind power generation have an advantage of unlimited and unpolluted amount of energy resource. In conventional wind generation systems, since the blade rotates at low speed when the velocity of wind decreases their operations are possible only under limited conditions. Therefore they are in trouble of self-generation without the help of auxiliary generation devices outside. The system driven by the wind force in this paper consists of a generator, an invertor, batteries and sets for power storage with a spring. In this paper, the operation characteristics of system were analyzed through experiments for a trial product.