• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.3
• /
• pp.364-369
• /
• 1986

Silicon diaphragms, 10 and 20 \ulcorner-thick and 1x1 mm\ulcornerarea, have been fabricated by means of the electrochemical P-N junction etch-stop technique. The P-type diffused resistors were formed on the diaphragm, and the piezoresistance effect was examined. It was been found that the fractional variation of the resistance is dependent on the diaphragm thickness, resistor location, and resistor length, etc. The 1.2 k\ulcornerfull-brige pressure sensor with 10\ulcorner-thick diaphragm exhibits a pressure sensitivity of 42 \ulcorner/V\ulcornermHg with a temperature coefficient of 2.3 mmHg/\ulcorner, and shows a good linearity in the pressure range from 0 to 300 mmHg.

• Journal of Korean Society of Transportation
• /
• v.31 no.1
• /
• pp.77-86
• /
• 2013

This paper focuses on the development of analytical models for estimating the changes in saturation flow rates (SFR) at the stop-lines of a signalized intersection due to the existence of nearby work-zones, and thereby calculating the prevailing capacity values for specific lane groups. Major changes were incorporated in the logics of previous models and significant revisions have been made to secure the accuracy and simplicity. Furthermore, much attention was paid to model validation by making comparisons to both extensive simulation results and empirical data from various sites. It was found that SFRs are highly sensitive to the location of work-zones, the distance to each work-zone from the stop-line of a concerned approach, the number of lanes open and closed, and the effective green time. Using such geometric and operating conditions that constitute work-zone environment, the proposed models successfully estimated SFR values with a miniscule margin of error.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.424-430
• /
• 2021

Determining the cause of a traffic signal violation is difficult if the drivers' claims are contradictory. In this study, the process of identifying signal violations using a simulation was presented based on cases. First, statements from the driver or witness whose cause of the signal violation is unclear were excluded. Second, the final position, final location, damaged area, steering status, braking status, and road surface traces of the vehicle were collected. The impact point was investigated from the stop line. Third, simulation data were modified and entered until the collision situation of the accident vehicle and the final stop position were met. Fourth, if the simulation results were consistent with the crash situation, the facts were verified by cross-validation to conform to the driver's statement. The results of the simulation showed that the Lexus entered the left turn signal in the intersection at approximately 55 km/h. In comparison, the Sonata driver saw the vehicle straight ahead at the intersection, entered the 72 km/h intersection, and collided with the Lexus. Therefore, the Sonata was identified as a signal violation, and the claims of the Sonata driver, witnesses, and police were contradictory.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.5
• /
• pp.847-856
• /
• 2016

Recently, with a high level of economic growth, rapid urbanization, population, environment and housing problems were accompanied in Korea. In particular, the traffic problem has become a serious social problem. As the current transportation policy has been carried out, concentrating on traffic flow, in 2015, death rate for pedestrians while walking (1,795 persons) is 38.8% compared to entire death rate in car accident (4,621 persons), so there is need to solve it. Although, crosswalk should make pedestrian cross it safely, it has been made on the basis of the width of road without exact standard for current width of the crosswalk and the location of stop line. Moreover, in the area around many campuses or commercial facilities, crosswalks are set with not considering pedestrian passage, but designed uniformly. Therefore, the purpose of this study is to estimate reasonable dimension of crosswalk considering pedestrian traffic and walking speed and it makes the accident rate lower in the crosswalk, which has a lot of problems including decisions of vehicle traffic signal time, lack of pedestrian's signal timing, pedestrian's crossing of long-distance. The following are the methodology of the study. Firstly, for crosswalk calculation of specifications, examination relating existing regulations and researches dealing with crosswalk, pedestrians and stop line is needed. After analyzing problems of current width of crosswalk and stop line, present the methodology to calculation of specifications and basing on these things, calculation of specifications for crosswalk will be decided. In conclusion, the calculation of specification and improvement of stop line for crosswalk laid out in this study are expected to be utilized as base data in case of establishing relevant safety facilities and standards.

• Journal of Industrial Convergence
• /
• v.18 no.1
• /
• pp.25-33
• /
• 2020

South Korea entered an aged society phase in 2017 with the elderly accounting for 14% or higher of the entire population. It is expected to enter a super-aged society phase in 2026. The mobility handicapped, including the disabled and the elderly, are expected to grow continuously, and the demand for transport service for the mobility handicapped will definitely increase further. Thus, there is thus a need for various research to increase the utilization rate of low-floor buses among the mobility handicapped. This study analyzed the locations of getting on and off transportation means, time of departure and arrival, purpose of use, and frequency of use by the day among the mobility handicapped by making use of the information about their use of special transport service run by the mobility support center for the mobility handicapped. The study then proposed a method of selecting locations for low-floor bus stops to reflect the distribution and need of getting on and off transportation means among the mobility handicapped with such spatial analysis techniques as geocoding, overlapping analysis, buffer analysis, and generate tessellations. Finally, the study selected 228 locations for low-floor bus stops in Cheonan and reported a need to add 35 low-floor bus stops after eliminating the ones where the locations overlapped the old ones.

• Journal of the Economic Geographical Society of Korea
• /
• v.15 no.2
• /
• pp.332-342
• /
• 2012

The current research aims at classifying the bus stops as transfer center in order to establish the rational bus transfer systems. Existing research typically identifies characteristics of demands for bus stops and land use surrounding the bus stops and classifies and profiles the bus stops. A common problem with this type of research is that the results with cross-sectional characteristics of land use and bus stop usage do not capture the details of trip chain, the fundamental characteristics of the trips with transfer. This paper therefore examines bus stop classifications with such variables as transport mode chains, intermediate stop chains and timing chains. The analysis on the data collected on Monday 20 April 2009 for passengers of Gyeong-gi bus results in a clear classification among bus stops in terms of such trip chain variables. The research would provide useful information for the decision support of transfer stops location choice and infrastructure design.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1D
• /
• pp.1-9
• /
• 2009

Bus information system(BIS), as a part of the intelligent transportation system(ITS), is one of the most advanced public transportation systems which provide the real-time bus traffic information for the users waiting the buses at the bus stop. However, correct bus information data, such as the present bus location, the user waiting time, the bus arrival time, etc. are not provided for the bus users because the proper bus arrival time predictive models are not used yet in most of the cities operating the bus information system, including the metropolitan City of Ulsan. Thus, the purpose in this study is to investigate real-time bus traffic characteristic data for identifying the bus operation characteristics on the arterial under the study in the metropolitan City of Ulsan, analyze real-time bus traffic characteristic data on the ID locations of the arterial under the study, construct the optimal unit segment models for the unit segments which are the bus stop, node and travel section using the exponential smoothing, weighted smoothing and Kalman Filter methods, respectively, and finally suggest the optimal integrated model for predicting the real-time bus arrival time at the bus stop of the arterial under the study.

• Journal of Korean Society of Transportation
• /
• v.28 no.6
• /
• pp.109-120
• /
• 2010

This study aims to develop mathematical models for estimating saturation flow rates at the stop line of signalized intersection due to Workzones in the vicinity, since the saturation flow rate is the most critical parameter in capacity analysis for signalized intersections. It was found by reference review that saturation flow rates are sensitively influenced by the location of Workzone, the number of lanes, cycle length and effective green time. Extensive microscopic simulation runs were also performed and compared to the those of mathematical models for model verification. Mathematical models were developed based on traffic flow theory and dualizing them by the location of workzones. And then each result produced by changing important parameter values was carefully examined and analyzed. Small but consistent differences in saturation flow rate values between mathematical models and simulations exist. However, the pattern of changes in saturation flow rates depending on each variable was similar.

• Journal of Korean Society of Transportation
• /
• v.26 no.2
• /
• pp.57-67
• /
• 2008

Loading zone is necessary to central business district(CBD) due to freight trucks coming into inner city. Currently truck drivers in metropolitan area are forced to illegally park their freight trucks on the roads close to the business facilities because there is no or few loading zones available in the CBD. This situation would bring into traffic congestion and even might block local roads in the CBD. This study reviews the existing improvement plans in city logistics, and examines delivery characteristics related to freight trucks and drivers in Seomyeon, the central downtown of Busan. Also it conducts a location planning for on-street loading/unloading bay using a technical method for arranging loading space. This research estimated the number of parking and stop bays for truck's operation using queueing theory based on truck-service rate and arrival rate, and found locations with the minimum resistance function values for freight movement in arranging on-street loading/unloading bays.

• The KIPS Transactions:PartD
• /
• v.19D no.2
• /
• pp.127-132
• /
• 2012

In the Seoul metropolitan bus network, it may be necessary for a bus passenger to pick up a parcel, which has been purchased through e-commerce, at his or her convenient bus stop on the way to home or office. The flow-capturing location-allocation model can be applied to select pickup points for such bus stops so that they maximize the captured passenger flows, where each passenger flow represents an origin-destination (O-D) pair of a passenger trip. In this paper, we propose a fast heuristic algorithm to select pickup points using a large O-D matrix, which has been extracted from five million transportation card transactions. The experimental results demonstrate the bus stops chosen as pickup points in terms of passenger flow and capture ratio, and illustrate the spatial distribution of the top 20 pickup points on a map.