• 대한치과보철학회지
• /
• 제48권4호
• /
• pp.280-286
• /
• 2010

연구 목적: 본 연구는 다수의 임플란트에 의해 지지되는 보철물을, 두 가지 인상법에 의해 얻은 모형들에 연결한 후, 나사의 풀림 토크값을 측정하여 나사 결합부 안정성에 차이가 있는지를 알아보는데 그 목적이 있다. 연구 재료 및 방법: 네 개의 외부 육각 임플란트 (Br${\aa}$nemark $System^{(R)}$; Nobel Biocare AB)에 직접 연결되는 임플란트 상부 구조물과, 이와 수동적 적합을 갖는 완전 무치악 하악주모형을 만들었다. 이 주모형에서 비연결 인상법으로 6회 인상을 채득하여 6개의 모형 (1군)을 제작하고, 아크릴릭 레진을 이용한 연결 인상법으로 6회 인상을 채득하여 6개의 모형 (2군)을 제작하여, 총 12개의 실험모형을 제작하였다. 각 실험모형에 상부 구조물을 지대주 나사 ($TorqTite^{(R)}$ GoldAdapt Abutment Screw; Nobel Biocare AB)로 20 Ncm의 힘으로 조인 후 각 나사의 풀림 토크값을 총 2회 측정하였다. 두 군 간 나사의 풀림 토크값의 비교를 위한 통계분석은 반복측정을 고려하고 나사와 reading을 고정효과로, 모형을 랜덤효과로 포함하는 혼합모형 (mixed model)을 이용하여 유의수준 .05에서 실시하였다. 결과: 나사의 풀림 토크값의 평균은 7.9 Ncm (1군)과 8.1 Ncm (2군)이었으며, 4개 나사의 풀림 토크값 중 최소값인 최소 풀림 토크값의 평균은 6.1 Ncm (1군)과 6.5 Ncm (2군)이었다. 나사의 풀림 토크값은 두 군 간에 통계적으로 유의할 만한 차이가 없었고, 조인 순서와 위치가 서로 다른 4개의 나사 간의 풀림 토크값도 통계적으로 유의한 차이가 없었다. 최소 풀림 토크값도 두 군 간에 통계적으로 유의할 만한 차이가 없었다. 결론: 다수의 외부 육각 임플란트에 의해 지지되는 보철물에서, 나사의 풀림 토크값과 최소 풀림 토크값은 비연결 인상법과 연결 인상법에 의해 얻어진 모형 간에 차이가 없어, 나사 결합부 안정성에 차이가 없는 것으로 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.237-242
• /
• 1998

Covering mortar as a filter for permeable polymer concrete is necessary for good permeability from filtration continuously. Therefore, this paper is intended as an evaluation of the mechanical properties and permeability of permeable polymer concrete covered with polymer mortar as a filter. An optimum permeable polymer concrete is selected in various mix proportions, and three different polymer mortars were cast immediately following on the casting of the base permeable polymer concrete. And they are tested for compressive and flexural strengths, adhesion in tension, hardening shrinkage and permeability . From the test results, binder and filler contents in mix proportions had a great influence on the permeability of polymer concretes. The mechanical properties of permeable polymer concretes covered with polymer mortars using crushed stone are superior to other filters, and hardening shrinkage is the smallest in filters. It is apparent that adhesion between the base permeable polymer concrete and polymer mortar is affected by the degree of hardening shrinkage. From this study, proper mix proportions can be recommended in the consideration of properties of the permeable polymer concrete.

• 대한치과기공학회지
• /
• 제35권4호
• /
• pp.321-332
• /
• 2013

Purpose: This study was examined the characteristics of bacteria isolated from the dental stone that is made ??in the dental laboratory. Methods: 104 dental stones samples were collected from the 4 dental laboratory. Characteristics of bacteria were investigated by microorganism isolation culture method using a Blood Tryptic Soy Agar(TSA) medium. Results: The detected various bacteria was confirmed as pathogenic bacteria, non-pathogenic bacteria and natural bacteria. The isolated bacterial number was confirmed $2.9{\times}10^3CFU$ and maxium bacterial number of $3.0{\times}10^4CFU$. Conclusion: Therefore, infection prevention education is required, it must be to live up the hand-washing and wear protective clothing to protect themselves when working in a dental laboratory.

• 대한치과보철학회지
• /
• 제45권4호
• /
• pp.546-554
• /
• 2007

Statement of problem: Die materials require abrasion resistance, dimensional stability with time, and high surface wettability for adequate material properties. Wear of gypsum materials is a significant problem in the fabrication of accurately fitting cast prosthetic devices. So It has been recommended that the use of die hardener before carving or burnishing of the wax pattern. Purpose: The purpose of this study was to compare the abrasion resistance and surface microhardness(Knoop) with 3 commonly used gypsum die materials(MG Crystal Rock, Super plumstone, GC $FUJIROCK^{(R)}$ EP) with and without the application of 2 die hardeners. Material and methods: Three die materials were evaluated for abrasion resistance and surface microhardness after application of 2 die hardeners(Die hardener and Stone die & plaster hardener). Thirty specimens of each gypsum material were fabricated using an impression of resin die(Pattern resin; GC Corporation, Japan) with 1-mm high ridges, sloped 90 degrees. Gypsum materials were mixed according to manufacturer's recommendations and allowed to set 24 hours before coating. Specimens were arbitrary assigned to 1 of 3 treatment subgroups (n=10/subgroup): no treatment(control), coated with Die hardener, and coated with Stone die & plaster hardener. Abrasion resistance(measured by weight loss) was evaluated using device in 50g mass perpendicular to the ridges. Knoop hardness was determined by loading each specimen face 5 times for 15 seconds with a force of 50g. A scanning electron microscope was used to evaluate the surface of specimens in each treatment subgroup. Conclusions: The obtained results were as follows: 1. 3 types of die stone evaluated in this study did not show significant differences in surface hardness and abrasive resistance(P<.05). 2. In the abrasive resistance test, there were no significant differences between GC $FUJIROCK^{(R)}$ EP and MG Crystal Rock with or without 2 die hardener(P<.05). 3. Super plumstone treated with Stone die & plaster hardener showed increased wear loss(P<.05) 4. Die hardener coatings used in this study decreased the surface hardness of the gypsum material(P<.05).

• 헤리티지:역사와 과학
• /
• 제54권2호
• /
• pp.4-21
• /
• 2021

부여 능산리 서고분군 4차 발굴조사(2016년) 과정에서 석제용범이 1점 출토되었다. 석제용범은 초기철기시대의 동침 용범으로 보고되었지만 주형 형태로 보아 동침이 아닌 가랑비녀의 용범으로 추정된다. 이에 본고에서는 능산리 출토 석제용범에 대해 고고학적 분석을 통해 유물의 형태와 시기를 세밀하게 파악하고 자연과학적 분석을 통해 석재 재질 특성과 그 산지를 추정해 보았으며 이를 바탕으로 능산리 일대에서 가랑비녀 석제용범이 사용된 양상도 파악해 보았다. 용범은 평면 장방형(단면 장방형)에 가까운 형태로 석재의 표면에는 4줄로 나란하게 홈이 나 있다. 홈은 2줄씩 단측면 가까이에서 이어져 각각 좁은 ∩형을 이룬다. 주형 형태로 보아 용범은 각부 끝으로 갈수록 좁아지는 ∩형의 가랑비녀를 제작했던 유물로 추정된다. 한반도에서 가랑비녀는 낙랑을 포함하여 원삼국시대부터 나타나 삼국시대(백제)에 소수 나타나고 통일신라시대를 거쳐 고려시대에 상당히 성행한다. 가랑비녀는 시대별 형태 차이가 뚜렷한 편인데, 능산리 용범은 주형 형태로 보아 고려시대에 제작되어 사용된 유물로 판단된다. 능산리 서고분군에서는 이와 관련되는 유구로 고려시대로 추정되는 수혈유구도 확인되었다. 능산리 가랑비녀 용범을 제작한 석재는 녹니석, 각섬석, 활석을 주성분 광물로하는 녹니석편암으로 녹회색의 무르고 부드러운 석재이다. 이러한 암석은 인근의 부여 외산면, 청양, 공주, 예산지역 등에서 산출되는데 현장조사를 통해 능산리 용범과 가장 비슷한 것은 부여 외산면 지선리에서 예산 예산읍 수철리 일대에 이르는 지역에 넓게 분포하는 것으로 확인하였다. 그리고 부여 능산리와 그 주변 지역에서 출토된 고려시대 가랑비녀는 현재까지 70점 정도인데, 그 중 능산리 용범의 주형과 가장 비슷하게 제작했을 것으로 추정되는 유물은 부여 송국리 유적 분묘 출토 청동제 가랑비녀 등이다. 그동안 남한 지역에서 출토된 가랑비녀 석제용범은 10점을 넘지 못하는데, 대부분 통일신라시대 유물이고 확실한 고려시대 유물은 매우 드물다. 능산리 석제용범으로 보아 고려시대에는 다양한 청동기 제작기술이 존재했겠지만 주조공정도 함께 있었음을 알 수 있다. 청동유물을 제작하기 위한 석제용범은 주형을 새기는 작업이 용이한 석재를 우선적으로 선택하고자 했을 것이다. 능산리 출토 가랑비녀 용범은 고려시대(전기)에 20~50km 정도 떨어진 인근 지역(부여 외산면 지선리에서 예산 예산읍 수철리 일대)에서 용범 제작이 용이한 석재를 가져다가 청동유물을 제작한 후 이를 인근 유적(부여 송국리 유적 등) 일대에 공급했던 양상과 함께 이 시기까지도 석제용범을 이용한 주조 기술이 존재했음을 보여준다.

• 한국수학사학회지
• /
• 제26권1호
• /
• pp.21-32
• /
• 2013

20세기 초에 발생하였던 제1, 2차 세계대전들은 유럽 사회뿐만 아니라, 수학계에도 지대한 손실을 끼쳤다. 1차 세계대전 이후 프랑스를 중심으로 탄생되었던 국제 수학연맹(IMU)은 정치적으로 이용되었던 이유로 해체되어졌고, 제 2차 세계대전이 발생함에 따라 모든 국제 학회모임은 중단되었다. 독일에 나치정권이 들어선 후, 많은 뛰어난 수학자들이 수용소에서 죽음을 맞거나 미국으로 이주하면서 학문의 중심은 유럽에서 미국으로 이동하였다. 전쟁이 끝난 후 심각한 정치 경제 위기에 처한 유럽의 학자들은 수학계를 대변할 능력을 잃었다. 이에 국제적인 의무감을 갖게 된 미국의 스톤(Stone)을 비롯한 수학자들은 정치에 상관없이 모든 나라가 가입할 수 있는 새 IMU를 탄생시킨다. 이 논문은 제2차 세계대전 이후에 IMU의 재탄생 과정과 1950년도의 ICM에서 일어난 일들을 면밀히 알아봄으로써 20세기 중반의 수학계의 발전상을 연구하고자 한다.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.353-359
• /
• 2012

Purpose: The aim of this study measured and compared the marginal and internal fit of metal cores with two base metal alloy (Ni-Cr alloy(non-beryllium), Co-Cr alloy). Methods: Maxillary right first molar abutment fabricated by titanium was prepared for this study. Impressions(10ea) were made from titanium model, and study models were poured with improved dental stone. Wax cores of twenty were prepared for burn-out and casting. Ten wax cores cast Ni-Cr alloy(non-Be), and finally ten cast Co-Cr alloy. Marginal and internal fit of cores was evaluated using silicone replica technique and digital microscope(x160). The data were statistically analyzed with the independent samples t-test (${\alpha}$ <.05). Results: Mean(standard deviation, SD) marginal and internal fit total size of Ni-Cr alloy(non-Be) group was $73.3(14.4){\mu}m$ and of Co-Cr alloy group $65.6(17.4){\mu}m$. The marginal and internal fit total size of Ni-Cr alloy group(non-Be) was statistically significantly greater than that of Co-Cr alloy group (P=.004). Conclusion: Co-Cr alloy cores in this study had a better marginal fit than Ni-Cr alloy(non-Be) cores.

• The Journal of Advanced Prosthodontics
• /
• 제12권4호
• /
• pp.210-217
• /
• 2020

PURPOSE. The purpose of the study is to evaluate the repeatability and reproducibility of the abutment angle using a blue light scanner. MATERIALS AND METHODS. 0°, 6°, and 10° wax cast abutment dies were fabricated. Each of the silicone impression was produced using the replicable silicone. Each study die was constructed from the prepared replicable stone used for scans. 3-dimensional data was obtained after scanning the prepared study dies for the repeatability by using the blue light scanner. The prepared 3-dimensional data could have the best fit alignment using 3-dimensional software. For reproducibility, each abutment was used as the first reference study die, and then it was scanned five times per each. 3-dimensional software was used to perform the best fit alignment. The data obtained were analyzed using a nonparametric Kruskal-Wallis H test (α=.05), post hoc Mann-Whitney U test, and Bonferroni correction (α=.017). RESULTS. The repeatability of 0°, 6°, and 10° abutments was 3.9, 4.4 and 4.7 ㎛, respectively. Among them, the 0° abutment had the best value while the 10° abutment showed the worst value. There was a statistically significant difference (P<.05). The reproducibility of 0°, 6°, and 10° abutments was 6.1, 5.5, and 5.3 ㎛, respectively. While the 10° abutment showed the best value, the 0° abutment showed the worst value. However, there was no statistically significant difference (P>.05). CONCLUSION. In repeatability, the 0° abutment showed a positive result. In reproducibility, the 10° abutment achieved a positive result.

• 국제초고층학회논문집
• /
• 제9권1호
• /
• pp.53-60
• /
• 2020

"A practical architect might not unnaturally conceive the idea of erecting a vast edifice whose frame should be entirely of iron, and clothing the frame--preserving it--by means of a casing of stone…that shell must be regarded only as an envelope, having no function other than supporting itself..." --Viollet-le-Duc, 1868. Viollet-le-Duc's recipe for an encased iron frame foresaw the separation of structural and enclosing functions into discrete systems. This separation is an essential characteristic of skyscrapers today, but at the time of his writing cast iron's brittle nature meant that iron frames could not, on their own, resist lateral forces in tall structures. Instead, tall buildings had to be braced with masonry shear walls, which often also served as environmental enclosure. The commercial availability of steel after the 1880s allowed for self-braced metal frames while parallel advances in glass and terra cotta allowed exterior walls to achieve vanishingly thin proportions. Two Chicago buildings by D.H. Burnham & Co. were the first to match a frame "entirely of iron" with an "envelope" supporting only itself. The Reliance Building (1895) was the first of these, but the Fisher Building (1896) more fully exploited this new constructive typology, eschewing brick entirely, to become the first "building without walls," a break with millennia of tall construction reliant upon masonry

• 대한치과보철학회지
• /
• 제28권2호
• /
• pp.91-108
• /
• 1990

The purpose of this study was to compare the maganitude of the discrepancies of the mounting errors in according to the states of dentitions, and to the superoinferior, anteroposterior, and rightleft driecetions. GROUP I. : Fourteen patients 22 to 26 years of age with a full complement of teeth, were used in the study. The criteria fro patient selection were a complete dentition, sparse restorarive treatment, and adequate posterior and anterior occlusan stops. And they had no sign and sympton at TMG area. GROUPII. : Eigth patients 37 to 62 years of age with bilateral free ends. The criteria for patient selection were Kennedy classification class 1 cases, and adequate posterior and anterior stops. And the opposite dentitions were a full complement of teeth. Irreversible hydrocolloid impresiion of each arch was taken of each patient. These were immediatel poured in stone and mounted on a Denar Mark II. Articulator with the arbitrary slidematic face-bow. With hand articulation th e mandibular cast was mounted to the maxillary cast in centric occlusion. Five types of interocclusal records were taken of each patient : (1) aluwax (2) baseplate wax; (3) znic oxide-eugenol pasts; (4) polyether (Ramitec); (5) modeling compound. All measurement of the five selected recording materials were compared with those of the hand-articulated full arch models in centric occlusion or maximum interdigitation. The results were as follows; 1. There were statistical differences in amount of devitation in according to the materials and the states of dentition. The amount of deviation of compound was the largest. 2. There were statistical differences in amount of deviation in complete dentition at all directions. The amount of diviation of compound was the largest. And at the right-left direction the amount of znic oxide-eugenol paste was larger than that of baseplate wax. 3. There was a statistical difference in amount of diviations in partial edentulous dentition at the superoinferior direction. The amount of deviation of compound was larger than that of znic oxide-eugenol paste. 4. There was as statistical difference in amount of deviations in partial edentulous dentition at the right-left direction. The amount of deviation of baseplate wax was larger that tnat of polyether. 5. There was not a statistical difference in amount of diviation in partial edentulous dentition at the anteroposterior direction.