• Journal of Korea Soil Environment Society
• /
• v.4 no.1
• /
• pp.3-11
• /
• 1999

The effects of major cations in soils, soil : extractant ratio, and EDTA : lead stoichiometric ratio on the extraction efficiency of lead using EDTA were studied for 4 different actual lead-contaminated soils and one artificially lead-contaminated soil. Extraction of lead from the lead-contaminated soil was not affected by a soil : extractant ratio as low as 1 : 3 but instead was dependent on the quantity of EDTA present. Results of the experiments showed that the extraction efficiency for each soil was different, but if sufficiently large amount of EDTA was applied, all the lead may be extracted except for a soil from lead mining area. The differences in extraction efficiencies nay be due to the major cations present in soils which may compete with lead for active sites on EDTA. The total molar amount of major cations extracted was as muck as 20 times more than the added molar amount of EDTA. For some of the soils tested, the extraction efficiency of lead may be affected by being occluded in the Fe and Mn oxides present in the soil. While major cations present in the soil may be one of the factors affecting lead extraction efficiency, the type of lead species present may also play a role. When these factors affect severely, the using of EDTA to extract lead from lead-contaminated soil might be non-effective method.

• Journal of Powder Materials
• /
• v.23 no.5
• /
• pp.384-390
• /
• 2016

Tri-isotropic (TRISO) coatings on zirconia surrogate beads are deposited using a fluidized-bed vapor deposition (FB-CVD) method. The silicon carbide layer is particularly important among the coated layers because it acts as a miniature pressure vessel and a diffusion barrier to gaseous and metallic fission products in the TRISO-coated particles. In this study, we obtain a nearly stoichiometric composition in the SiC layer coated at $1400^{\circ}C$, $1500^{\circ}C$, and $1400^{\circ}C$ with 20 vol.% methyltrichlorosilane (MTS), However, the composition of the SiC layer coated at $1300-1350^{\circ}C$ shows a difference from the stoichiometric ratio (1:1). The density decreases remarkably with decreasing SiC deposition temperature because of the nanosized pores. The high density of the SiC layer (${\geq}3.19g/cm^2$) easily obtained at $1500^{\circ}C$ and $1400^{\circ}C$ with 20 vol.% MTS did not change at an annealing temperature of $1900^{\circ}C$, simulating the reactor operating temperature. The evaluation of the mechanical properties is limited because of the inaccurate values of hardness and Young's modulus measured by the nano-indentation method.

• Korean Journal of Materials Research
• /
• v.12 no.7
• /
• pp.573-579
• /
• 2002

Stoichiometric mullite ($3Al_2$$O_3$. $2SiO_2$) precursor sol has been prepared by sol-gel method. The effects of the precursor pH and sintering temperature on the synthesizing behavior and morphology of mullite have been studied. Mullite precursor sol was prepared by dissolution of aluminum nitrate enneahydrate (Al($NO_3$)$_3$.9H$_2O) into the mixture of silica sol. Precursor pH of the sols was controlled to acidic condition ($PH\leq$ 1~1.5) and to basic condition ($pH\geq$8.5~9). The synthesized aluminosilicate sols were formed under 20 MPa pressure after drying at $150^{\circ}C$ for 24 hours, and then sintered for 3hours in the temperature range of $1100~1600^{\circ}C$. From TGA/DTA analysis, total weight loss in the aluminosilicate gel of the acidic sample was (equation omitted) 56% and that of the basic sample was (equation omitted) 85%, indicating that the synthesizing temperature of mullite phase for acidic and basic samples was above $1200^{\circ}C$ and $1300^{\circ}C$, respectively. The morphologies of the synthesized mullite were fine and needle-like (or rod-like) for acidic sample, and granular for basic sample that has been sintered above $1300^{\circ}C$. It was found that the morphology of mullite particle was predominantly governed by precursor pH and sintering temperature.

• The Korean Journal of Ceramics
• /
• v.5 no.3
• /
• pp.217-223
• /
• 1999

Proten-conductive $SrZr_{0.95} Y_{0.05} O_{2.975}$ powder was prepared by citrate gel method its characteristics and sinterability were investigated. Amorphous gel could be obtained from a citric acid solution that $SrCO_3$ and metal nitrates were dissolved. The initial decomposition of the gel proceeded up to $250^{\circ}C$, followed by combustion of its decomposition products in the temperature range from $250^{\circ}C$ to $500^{\circ}C$. A well-crystallized perovskite phase with a stoichiometric composition after calcination at $1000^{\circ}C$. Sintering green compacts of this powder for 6 h showed a considerable densification to start at $1200^{\circ}C$ and resulted in 86.8% and 96.5% relative densities at $1400^{\circ}C$ and $1600^{\circ}C$, respectively. Whereas, the powder compacts prepared by solid state reaction had much lower relative densities, 73% at $1400^{\circ}C$ and 92% at $1600^{\circ}C$.

• Journal of Pharmaceutical Investigation
• /
• v.12 no.4
• /
• pp.132-144
• /
• 1982

The inclusion of ${\beta}-cyclodextrin$ $({\beta}-CyD)$ with prothionamide in aqueous phase was investigated by circular dichroism(CD), ultraviolet (UV) absorption, and solubility technique. The results suggested that a region of drug chromophore was located within the asymmetric center of ${\beta}-cyclodextrin$. Solubility and spectral changes were quantitatively treated to obtain stoichiometric ratio, which was found to be 1 : 1, and formation constants which were determined by solubility, CD, and UV method were 257, 367, and 389 $M^{-1}$, respectively. Also, the formation constant of the inclusion complex was determined by CD method at various pH. The result was that $K_c$ depended upon the pH of medium, and this fact also supported that thioamide moiety was accomodated in the cavity of ${\beta}-cyclodextrin$.

• Journal of the Korean Chemical Society
• /
• v.9 no.3
• /
• pp.113-115
• /
• 1965

In previous paper, the determination procedure of fission products mainly consists of many steps which are usually derived from classical analysis schemes. In the present paper a simple and more rapid method of the determination of fission products by means of a smaller amount of reagent than that correspond to the stoichiometric ratio of element to be determined is investigated. The yield of Ba-140 in fission products is determined by this method.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.3
• /
• pp.169-174
• /
• 2004

MgO thin films were reactively deposited using an internal inductively coupled plasma assisted sputtering method varying reactive gas ratio to get stoichiometric film composition, and bipolar dc substrate bias to suppress micro arcs. The minimum frequency required for arc suppression was about 10KHz depending on ICP power. Their crystallinity was analyzed using X-ray diffraction and surface morphology using AFM. The surface was very smooth with rms roughness less than 0.42nm. The preferred orientation of the films were changing from (200) to bulk-like characteristics as Ar: $O_2$ratio was controlled to 10 : 2. Optical emission spectroscopy revealed that there were two distinct discharge modes: a blue one and a green one, where enhanced emission from Ar and Mg were observed. This cannot simply be understood by metallic or oxide mode of reactive sputtering due to ICP coupled to magnetron discharge.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.21-23
• /
• 2003

MOCVD method is one of promising techniques which can fabricate YBCO coated conductors in a low Price A continuous reel-to-reel MOCVD device using a dispersed solid source was designed and manufactured. YBCO films were deposited on various substrates of metallic silver, (100) MgO and SrTiO3 single crystals. The chemical composition of the metal organic sources was changed to optimize the processing condition associate to the deposition of the stoichiometric Y3a2Cu3O7-y. We report the superconducting transition temperature, surface morphology and chemical composition of the YBCO film surfaces.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.440-441
• /
• 2006

Several titanate powders ($Al_2TiO_5,\;SrTiO_3$, etc.) were synthesized by an ethylene glycol solution route. Titanium isopropoxide and nitrate salts were dissolved in stoichiometric proportions in liquid-type ethylene glycol without any precipitation. The parent precursor sols were dried to porous gels, and then the gels were calcined and crystallized. All synthesized titanate powders had stable crystallization behavior at low temperature and high specific surface area after a simple ball-milling process. A three-component PZT $(Pb(Zr_{0.52}{\cdot}Ti_{0.48})O_3)$ powder was also synthesized successfully by the ethylene glycol method. In this study, the characteristics of the multi-component titanate powders by the ethylene glycol method are examined.

• Journal of the Korean Society of Combustion
• /
• v.1 no.2
• /
• pp.41-49
• /
• 1996

A numerical study is conducted to investigate the periodically unstable shock induced combustion around blunt bodies in stoichiometric hydrogen-air mixtures. Euler equations are spatially discretized by upwind-biased third order scheme and temporally integrated by Runge-Kutta method. Chemistry model used in this study involves 8 elementary kinetics steps and 7 species. At a constant Mach number, the effects of projectile size, inflow pressure and inflow temperature are examined with Lehr#s experimental condition as a reference. In addition to oscillation frequency, characteristic distances and time averaged values are found from the result to find an relation with dimensionless parameters. As a result, it is found that the effects of inflow pressure and body size are very similar and $Damk{\ddot{o}}hler$ number plays an important role in determining the instability characteristics.