• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.593-598
• /
• 2000

In this paper the critical speed analysis and design sensitivity investigation are carried out with an APU(auxiliary power unit) gas turbine having a spline shaft connection. The DDM(direct differential method) is directly applied to formulate the critical speed design sensitivity problem of a general nonsymmetric-matrix rotor-bearing system. The design sensitivity analysis have shown that the critical speed change rate to the support modeling of the spline shaft connection point is extremely negligible, and thereby its design uncertainty is lifted. It has also been confirmed that the critical speeds up to the 4th are not sensitive to the design stiffness coefficients of 4-main bearings or supports, including two air foil bearings. Further, the critical speed change rate to the shaft-element length have shown quantitatively that the spline shaft has some limited influence on the 4th critical speed.

• Wind and Structures
• /
• 제11권6호
• /
• pp.497-512
• /
• 2008

In this paper, optimum methods of wind-induced vibration control of high-rise buildings are mainly studied. Two optimum methods, genetic algorithms (GA) method and Rayleigh damping method, are firstly employed and proposed to perform optimum study on wind-induced vibration control, six target functions are presented in GA method based on spectrum analysis. Structural optimum analysis programs are developed based on Matlab software to calculate wind-induced structural responses. A high-rise steel building with 20-storey is adopted and 22 kinds of control plans are employed to perform comparison analysis to validate the feasibility and validity of the optimum methods considered. The results show that the distributions of damping coefficients along structural height for mass proportional damping (MPD) systems and stiffness proportional damping (SPD) systems are entirely opposite. Damping systems of MPD and GAMPD (genetic algorithms and mass proportional damping) have the best performance of reducing structural wind-induced vibration response and are superior to other damping systems. Standard deviations of structural responses are influenced greatly by different target functions and the influence is increasing slightly when higher modes are considered, as shown fully in section 5. Therefore, the influence of higher modes should be considered when strict requirement of wind-induced vibration comfort is needed for some special structures.

• 근관절건강학회지
• /
• 제21권3호
• /
• pp.195-205
• /
• 2014

Purpose: This study was conducted to identify factors that influence health-related quality of life in older adults with osteoarthritis. Methods: This study used a cross-sectional design with secondary analysis of the Korean National Health and Nutrition Examination Survey 2011. A total of 362 participants aged 65 years and older who had osteoarthritis were selected. Health-related quality of life using EQ-5D, perceived health status, body mass index, numbers of chronic illness, smoking and alcohol use, exercise, activity limitation, joint pain and stiffness, depression, and perceived stress were measured. Descriptive statistics, $x^2$-test, t-test, ANOVA, Pearson's correlation coefficients, and multiple regression were conducted with SPSS/WIN 21.0. Results: The mean score of EQ-5D was 0.77 in older adults with osteoarthritis. The results of multiple regression analysis showed that age, income, subjective health status, restriction of activity, knee joint stiffness, depressive mood, and perceived stress significantly predicted health-related quality of life in older adults with osteoarthritis, explaining 42% of the variance. Conclusion: Older adults with osteoarthritis have low health-related quality of life. In oder to improve health-related quality of life in older adults with osteoarthritis, it is important not only to enhance physical function but also to provide emotional support.

• Wind and Structures
• /
• 제28권4호
• /
• pp.215-224
• /
• 2019

Because of the particularity and complexity of direct air-cooling structures (ACS), wind parameters given in the general load codes are not suitable for the wind-resistant design. In order to investigate the wind loads of ACS, two 1/150 scaled three-span models were designed and fabricated, corresponding to a rigid model and an aero-elastic model, and wind tunnel tests were then carried out. The model used for testing the wind pressure distribution of the ACS was defined as the rigid model in this paper, and the stiffness of which was higher than that of the aero-elastic model. By testing the rigid model, the wind pressure distribution of the ACS model was studied, the shape coefficients of "A" shaped frame and windbreak walls, and the gust factor of the windbreak walls were determined. Through testing the aero-elastic model, the wind-induced dynamic responses of the ACS model was studied, and the wind vibration coefficients of ACS were determined based on the experimental displacement responses. The factors including wind direction angle and rotation of fan were taken into account in this test. The results indicated that the influence of running fans could be ignored in the structural design of ACS, and the wind direction angle had a certain effect on the parameters. Moreover, the shielding effect of windbreak walls induced that wind loads of the "A" shaped frame were all suction. Subsequently, based on the design formula of wind loads in accordance with the Chinese load code, the corresponding parameters were presented as a reference for wind-resistant design and wind load calculation of air-cooling structures.

• Steel and Composite Structures
• /
• 제24권2호
• /
• pp.249-264
• /
• 2017

In this paper free linear vibration of lattice composite conical shells will be investigated. Lattice composite conical shell consists of composite helical ribs and thin outer skin. A smeared method is employed to obtain the variable coefficients of stiffness of conical shell. The ribs are modeled as a beam and in addition to the axial loads, endure shear loads and bending moments. Therefore, theoretical formulations are based on first-order shear deformation theory of shell. For verification of the obtained results, comparison is made with those available in open literature. Also, using FEM software the 3D finite element model of composite lattice conical shell is built and analyzed. Comparing results of analytical and numerical analyses show a good agreement between them. Some special cases as variation of geometric parameters of lattice part, effect of the boundary conditions and influence of the circumferential wave numbers on the natural frequencies of the conical shell are studied. It is concluded, when mass and the geometrical ratio of the composite lattice conical shell do not change, increment the semi vertex angle of cone leads to increase the natural frequencies. Moreover for shell thicknesses greater than a specific value, the presence of the lattice structure has not significant effect on the natural frequencies. The obtained results have novelty and can be used for further and future researches.

• Advances in aircraft and spacecraft science
• /
• 제3권3호
• /
• pp.331-349
• /
• 2016

Stiff and light fibre reinforced composites as used in air- and space-craft applications tend to high sound emission. Therefore, the damping properties are essential for the entire structural and acoustic engineering. Viscous damping is an established and reasonably linear model of the dissipation behaviour. Commonly, it is assumed to be isotropic and constant over all modes. For anisotropic materials it depends on the fibre orientation as well as the elastic and thermal material properties. To portray the orthogonal anisotropic behaviour, a model for unidirectional fibre reinforced plastics (frp) has been developed based on the classical laminate theory by ADAMS and BACON starting in 1973. Their approach includes three damping coefficients - for longitudinal damping in fibre direction, damping transversal to the fibres and shear based dissipation. The damping of a laminate is then accumulated layer wise including the anisotropic stiffness. So far, the model has been applied mainly to thermoset matrix materials. In this study, an experimental parameter estimation for different thermoplastic frp with angle ply and cross ply layups was carried out by measuring free vibrations of cantilever beams. The results show potential and limits of the ADAMS/BACON damping criterion. In addition, a possibility of modelling the anisotropic damping is shown. The implementation in standard FEA software is used to study the influence of boundary conditions on the damping properties and numerically estimate the radiated sound power of thin-walled frp parts.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1993년도 추계학술대회논문집
• /
• pp.243-251
• /
• 1993

With the recent issuance of a dynamic side impact test regulation in the Federal Motor Vehicle Safety Standard in the United States of America, many aspects of occupant protection in side impact crashes have been under investigation. Many investigations of real world accidents, crash test results and simulation studies have established that in side impact crashes of passenger cars, thoracic and pelvic injuries of occupant are, large part, caused by occupants' impact against the interior side of the vehicle, primarily the door. This paper is concerned with the development of a lumped mass computer model, which simulates the interaction of a struck car door and an adjacent seated occupant in side impacr, based CTP code which has been successfully used in vehicle and occupant simulation. New model developments include elimination of influence of vehicle side structure stiffness in the occupant injury responses. The model was used to investigated the effect of various door padding characteristics on occupant responses to improve vehicle safety performance. The evaluation of different crush properties of door padding have also focused to understand of behavior of impacted occupant. Results from simulations, The effects of both material coefficients $C_{f}$ and p were illustrated in terms of occupant injury criteria TTI and pelvis.

• 대한토목학회논문집
• /
• 제32권2A호
• /
• pp.109-116
• /
• 2012

지진격리장치로서 납고무받침의 동적 특성은 주재료인 고무재료의 동적거동과 비선형 성질에 의존하고 있다. 역학적이나 환경적인 영향으로 인해 고무재료에 노화가 진행되고 결국에는 손상이 불가피하게 발생하게 된다. 고무재료의 노화의 주원인은 높은 온도에서 반응열로 인한 산화반응으로 알려져다. 이에 따라 납고무받침의 가속 열 노화실험을 수행하여 열 노화 전 후에 대해 받침의 특성값을 상호 비교하였다. 실험 결과 열 노화 현상은 전단강성과 에너지 감쇠 그리고 등가감소계수에 영향이 있음을 알 수 있었다. 또한 열 노화에 의한 동적특성의 저하를 실제 교량에 적용하여 납고무받침의 열 노화가 교량의 교각의 내진성능에 미치는 영향을 수치해석을 통해 비교분석하였다. 해석결과 납고무받침에 대하여 열 노화에 따른 기본 특성변화가 교량의 내진성능에 미치는 영향은 크지 않음을 알 수 있었다.

• 대한토목학회논문집
• /
• 제33권3호
• /
• pp.855-864
• /
• 2013

지진격리장치로서 천연고무받침의 동적 특성은 주재료인 고무의 동적거동과 비선형 성질에 의존하고 있다. 역학적이나 환경적인 영향으로 인해 고무재료에 노화가 진행되고 결국에는 손상이 불가피하게 발생하게 된다. 고무재료의 노화에 주원인은 높은 온도에서 반응열로 인한 산화반응으로 알려져다. 이에 따라 천연고무받침에 대한 가속 열 노화실험을 수행하여 열 노화 전 후에 대해 받침의 특성값을 상호 비교하였다. 실험 결과 열 노화 현상은 전단강성과 에너지 감쇠 그리고 등가감소계수에 영향이 있음을 알 수 있었다. 또한 열 노화에 의한 동적특성의 저하를 실제 교량에 적용하여 천연고무받침의 열 노화가 교량의 내진성능에 미치는 영향을 수치해석을 통해 비교분석하였다. 그 결과 천연고무받침에 대하여 열 노화에 따른 기본 특성변화가 교량의 내진성능에 미치는 영향은 크지 않음을 알 수 있었다.

• Advances in concrete construction
• /
• 제8권3호
• /
• pp.173-185
• /
• 2019

This article presents a comparative study of the effect of steel layouts on the seismic behavior of transition steel-concrete composite connections, both experimental and analytical investigations of concrete filled steel tube-reinforced concrete (CFST-RC) and steel reinforecd concrete-reinforced concrete (SRC-RC) structures were conducted. The steel-concrete composite connections were subjected to combined constant axial load and lateral cyclic displacements. Tests were carried out on four full-scale connections extracted from a real project engineering with different levels of axial force. The effect of steel layouts on the mechanical behavior of the transition connections was evaluated by failure modes, hysteretic behavior, backbone curves, displacement ductility, energy dissipation capacity and stiffness degradation. Test results showed that different steel layouts led to significantly different failure modes. For CFST-RC transition specimens, the circular cracks of the concrete at the RC column base was followed by steel yielding at the bottom of the CFST column. While uncoordinated deformation could be observed between SRC and RC columns in SRC-RC transition specimens, the crushing and peeling damage of unconfined concrete at the SRC column base was more serious. The existences of I-shape steel and steel tube avoided the pinching phenomenon on the hysteresis curve, which was different from the hysteresis curve of the general reinforced concrete column. The hysteresis loops were spindle-shaped, indicating excellent seismic performance for these transition composite connections. The average values of equivalent viscous damping coefficients of the four specimens are 0.123, 0.186 and 0.304 corresponding to the yielding point, peak point and ultimate point, respectively. Those values demonstrate that the transition steel-concrete composite connections have great energy dissipating capacity. Based on the experimental research, a high-fidelity ABAQUS model was established to further study the influence of concrete strength, steel grade and longitudinal reinforcement ratio on the mechanical behavior of transition composite connections.