• 제목/요약/키워드: Stiffener

검색결과 434건 처리시간 0.03초

수직 행거 내진설계용 스티프너의 단조 압축 실험 (Monotonic Loading Tests on Seismic Stiffeners for Vertical Hangers)

  • 오창수;공하성
    • 대한안전경영과학회지
    • /
    • 제25권2호
    • /
    • pp.187-192
    • /
    • 2023
  • In piping systems, trapeze hangers are subjected to vertical and horizontal seismic loads and stiffeners are used. In this study, monotonic compression tests were conducted with the removable stiffeners using three variables: stiffener clamp fixing position, section length, and installation direction. The maximum load reinforced with stiffeners could withstand a compressive load of 11kN by applying a safety factor of 10%. It could be estimated that the fixing clamp spacing or the length of shape and load had a proportional relationship. And the stiffener must be fixed in the direction of the strong axis on hinge parts. Also the stiffener buckiling load design proposes to use a method of calculate the flexural buckling compressive strength of and unreinforced full threaded bolt.

보강형 현장타설말뚝의 최적보강효과 분석 (Optimization of Reinforcement Effect of Large-diameter Drilled Deep Foundation)

  • 남대승;김수일;이준환;윤경식
    • 한국지반공학회논문집
    • /
    • 제19권2호
    • /
    • pp.207-216
    • /
    • 2003
  • 본 연구에서는 철탑의 기초로 사용이 증가되고 있는 현장타설말뚝의 크기를 줄이기 위한 방안으로 말뚝주면에 가시모양의 보강재를 타설.정착시켜 지지력을 증가하는 보강형 현장타설말뚝에 대한 수치해석적 연구를 수행하였다. 보강재에 의한 지지력 증가효과의 크기를 정량적, 정성적으로 알아보기 위해 풍화토, 풍화암, 연암지반 등 국내의 대표적 지반을 대상으로 보강재의 단수, 경사 및 위치 등을 변화시켜 해석을 실시하였다. 보강재 단수변화의 경우, 풍화암과 연암지반에서는 단수증가에 따라 비례적으로 보강효과가 증가하였지만 풍화토의 경우 단수의 증가에 따라 보강효과 증가율이 작아지는 결과가 나타났다. 위치변화의 경우, 수평하중재하시 보강재가 상단에 위치한 경우가 하중을 직접적으로 지지하기 때문에 가장 보강효과가 좋은 것으로 나타났지만 압축, 인장하중의 경우 큰 차이가 나타나지 않았다. 경사변화의 경우, 연직하중일 때는 보강재 전 길이에 걸쳐 축력이 최대로 발휘되는 60$^{\circ}$의 경사일 때 보강효과가 가장 크게 나타났다. 하지만 수평하중일 때는 하중재하 방향과 일치하는 0$^{\circ}$에서 보강효과가 전반적으로 좋게 나타났다.

X형 관이음부의 보강방법에 따른 극한강도 해석 (Effect of Reinforcement Type on Ultimate Strength of Tubular X-Joints)

  • 조현만;류현선;김정태
    • 한국전산구조공학회:학술대회논문집
    • /
    • 한국전산구조공학회 2000년도 가을 학술발표회논문집
    • /
    • pp.230-237
    • /
    • 2000
  • Tubular joints of jacket structures are usually reinforced using thicker can section, internally ring stiffeners, diaphragm, or externally gusset plates to increase load carry capacity. In this paper, the effect of reinforcement type and geometric parameters of stiffener on the ultimate strength of tubular X-joints subjected to brace compression have been studied numerically Three reinforcement methods were considered; (1)can reinforcement (2)internally ring stiffener (3)internally longitudinal diaphragm. The ANSYS software was used nonlinear strength analysis. It was found that there is significant strength enhancement for reinforced joints.

  • PDF

비대칭연단보강재가 설치된 직교이방성 압축재의 탄성 국부좌굴해석 (Analysis of Elastic Local Buckling of an Orthotropic Compression Member with Asymmetric Edge Stiffeners)

  • 최원창;정상균;윤순종
    • 한국복합재료학회:학술대회논문집
    • /
    • 한국복합재료학회 2000년도 추계학술발표대회 논문집
    • /
    • pp.5-8
    • /
    • 2000
  • This paper presents the analytical investigation pertaining to the local buckling behavior of orthotropic open section thin-walled compression members with asymmetric edge stiffeners. In the analysis, 3 different cases of the second moment of inertia are considered to find the asymmetric edge stiffener effect on the local buckling strength. The analytical study results are presented in the graphical form so that the edge stiffener effects on the local buckling strength can be easily found.

  • PDF

전단 보강재의 보강길이에 따른 기초판의 뚫림전단 성능평가 (Punching Shear Performance Evaluation of Foundation by Enforcement-length of Shear Head Reinforcement)

  • 이용재;이원호;양원직
    • 한국구조물진단유지관리공학회 논문집
    • /
    • 제21권2호
    • /
    • pp.60-68
    • /
    • 2017
  • 본 연구에서는 지내력이 기초판에 미치는 영향을 충분히 고려할 수 있도록 현장여건과 동일한 옥외의 지반에서 실험할 수 있는 시스템을 구축하였으며, 대상 실험체는 경제성 및 시공성 향상을 위하여 강판을 "ㄷ"자형으로 절곡하여 단면 2차모멘트를 극대화 하고 현장조립이 가능하도록 제안 하였다. 대상 실험체는 무보강 실험체 1개, 강판 두께를 동일하게 하여 보강 길이를 달리한 실험체 3개, 강판 두께를 달리하고 위험단면 부근에 스티프너 보강한 실험체 2개 총 6개의 실험체를 대상으로 비교 검토 한다. 실험 결과 스티프너 보강에 의한 효과는 없는 것으로 나타났으며, 전단보강재의 보강길이는 확장된 위험단면에서 전단력을 지내력으로 나타낸 값과 위험단면에서 보강재가 받을 수 있는 전단내력을 지내력으로 환산여하여 두 선의 교차점을 유효보강 길이로 산정하는 강판두께별 유효보강길이 산정방법을 제안하였다.

2거더교의 수직보강재 연결상세부의 피로설계에 관한 연구 (A Study on the Fatigue Design of Joint Detail of Vertical Stiffener in Two-Girder Bridge)

  • 권순철;경갑수;박진은
    • 한국강구조학회 논문집
    • /
    • 제21권1호
    • /
    • pp.93-103
    • /
    • 2009
  • 2거더 플레이트교는 주부재인 바닥판과 거더, 2차부재인 가로보, 수직보강재 및 수평보강재 등으로 구성되어 있다. 2거더교는 AASHTO와 국내의 도로교설계기준에는 하나의 거더가 손상되면 그 교량의 기능과 안전성에 문제가 야기되는 단재하 경로 구조로 규정되어 있다. 이러한 이유 때문에 2거더교의 피로균열은 교량의 안전성에 심각한 영향을 줄 수 있다. 따라서 본 논문에서는 2거더교에서 피로균열 발생 가능성이 높은 수직보강재와 거더 복부의 연결부를 대상으로 수직보강재 스캘럽 곡률반경 및 복부두께를 변화시키면서 피로 평가를 수행하였다. 이 결과에 기초하여 피로에 유리한 구조상세 및 간이 평가식을 제안하였다.

바닥슬래브에 의해 구속된 철골 모멘트접합부의 내진보강에 관한 실험적 연구 (Experimental Study on Seismic Retrofit of Steel Moment Connections Considering Constraint Effect of the Floor Slab)

  • 오상훈;김영주;문태섭
    • 한국강구조학회 논문집
    • /
    • 제16권2호통권69호
    • /
    • pp.247-255
    • /
    • 2004
  • 본 실험프로그램은 슬래브가 있는 합성보의 내진성능향상을 위해 기존 모멘트접합부의 내진보강 방법을 개발을 목적으로 수행하였다. 반복하중을 통해 5개의 실대형 합성실험체에 대한 실험을 수행하였다. 각형강관기둥과 H형강보로 이루어진 기존의 다이아프램접합부가 RBS 또는 개량수평스티프너를 통해서 하부플랜지에만 내진 보강되었다. 제안한 보강접합부의 효율성을 조사하였다. 실험결과 하부플랜지에만 RBS를 적용한 접합부는 부족한 변형성능을 나타냈지만, 개량스티프너를 적용한 합성보 접합부는 내진성능을 향상시켰다.

비대칭 연단보강재가 설치된 직교이방성 개방단면 압축재의 탄성국부좌굴 (Elastic Local Buckling of Orthotropic Open Section Compression Members with Asymmetric Edge Stiffeners)

  • 윤순종;정상균
    • Composites Research
    • /
    • 제14권4호
    • /
    • pp.1-7
    • /
    • 2001
  • 본 연구는 등분포 압축을 받는 비대칭 연단보강된 직교이방성 개방단면 구조용 부재의 탄성국부좌괄에 대한 이론적 연구의 결과이다. 비대칭 연단보강재는 비틀림강성을 무시한 보요소로 간주하였다. 플랜지판의 일부와 플랜지의 연단에 부착된 판으로 구성된 비대칭 연단보강재에 대한 이론적 해석 모델을 제시하였으며, 이 결과로부터 얻어지는 비대칭 연단보강재 단면의 도심을 지나는 축에 대한 단면2차모멘트를 계산하였다. 유도된 식을 사용하여 비대칭 연단보강된 직교이방성 I형 압축재의 국부좌굴계수를 구하였으며 그 결과를 그래프로 제시하였다.

  • PDF

선체블록 론지 이면부 자동 도장 장비 개발 (Development of Automatic Painting Unit for Back-side of Longitudinal Stiffeners in Double Hull Blocks)

  • 김은태;이동훈;김호경
    • 대한조선학회 특별논문집
    • /
    • 대한조선학회 2009년도 특별논문집
    • /
    • pp.123-129
    • /
    • 2009
  • Ship painting procedures can be divided into two categories; Out-shell plate painting of the hull and the interior painting of each double gull blocks. It is really hard to apply standardized and automated operations to the latter because the double hull blocks contains a variety of complicated supportive materials and pipes to strengthen the ship structure. In addition their poor working conditions cause painting workers to avoid working in them, resulting in the waste of paints and additional pollution issues. So this research, successfully focused on overcoming the difficulties in working in the complicated blocks and the tough working conditions introduces the main details of automatic equipment systems and their transfer algorism which show how the equipment paints the inner sides of a longitudinal stiffener and moves to another automatically.

  • PDF

Experimental research on load-bearing capacity of cast steel joints for beam-to-column

  • Han, Qinghua;Liu, Mingjie;Lu, Yan
    • Structural Engineering and Mechanics
    • /
    • 제56권1호
    • /
    • pp.67-83
    • /
    • 2015
  • The load transfer mechanism and load-bearing capacity of cast steel joints for H-shaped beam to square tube column connection are studied based on the deformation compatibility theory. Then the monotonic tensile experiments are conducted for 12 specimens about the cast steel joints for H-shaped beam to square tube column connection. The findings are that the tensile bearing capacity of the cast steel joints for beam-column connection depends on the ring of cast steel stiffener. The tensile fracture happens at the ring of the cast steel stiffener when the joint fails. The thickness of square tube column has little influence on the bearing capacity of the joint. The square tube column buckles while the joint without concrete filled, but the strength failure happens for the joint with concrete filled column. And the length of welding connection between square tube column and cast steel stiffener has little influence on the load-bearing capacity of the cast steel joint. Finally it is shown that the load-bearing capacity of the joints for H-shaped beam to concrete filled square tube column connection is larger than that of the joints for H-shaped beam to square tube column connection by 10% to 15%.