• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.4
• /
• pp.273-278
• /
• 2008

This study was carried out in order to test unsaturated hydraulic conductivity estimation of van Genuchten's and Campbell's models using one-step outflow method through Tempe pressure cell. The undisturbed soil cores (columns) were taken from Ap1, B1 and C horizons of Songjeong series (the fine loamy, mesic family of Typic Hapludults). After the saturated hydraulic conductivity Ks of the cores was determined by constant head method, water outflow rate and retentivity of cores were measured in Tempe pressure cell. Fitted curves by models accorded to measured data except for both end of pressure range. In near-saturated condition, measured water retention characteristics showed a relatively better fitness with Campbell's model than van Genuchten's. The soil unsaturated conductivity estimated by Campbell's model was higher than by van Genuchten's. In Ap1 and B1 horizon, the soil unsaturated conductivities obtained by one-step outflow method went between van Genuchten's and Campbell's hydraulic functions, slightly closer to van Genuchten's. In C horizon, van Genuchten's model had better fitness with the one-step outflow data. Consequently, van Genuchten's model generally had better fitness with measured hydraulic conductivity than Campbell's model at the soil water potential range of -10~-75 kPa, especially in C1 horizon. In near-saturated condition, Campbell's model could be thought as relatively accurate hydraulic model, because of the better fitness of Campbell's model with soil water retention data than van Genuchten's model.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.11-15
• /
• 2001

In this paper, hermetic sealing technology was studied for wafer level packaging of the RF-MEMS devices. With the flip-chip bonding method. this non-conductive B-stage epoxy sealing will be profit to the MEMS device sealing. It will be particularly profit to the RF-MEMS device sealing. B-stage epoxy can be cured by 2-step and hermetic sealing can be obtained. After defining 500 $\mu\textrm{m}$-width seal-lines on the glass cap substrate by screen printing, it was pre-baked at $90^{\circ}C$ for about 30 minutes. It was, then, aligned and bonded with device substrate followed by post-baked at $175^{\circ}C$ for about 30 minutes. By using this 2-step baking characteristic, the width and the height of the seal-line could be maintained during the sealing process. The height of the seal-line was controlled within $\pm$0.6 $\mu\textrm{m}$ in the 4 inches wafer and the bonding strength was measured to about 20MPa by pull test. The leak rate, that is sealing characteristic of the B-stage epoxy, was about $10^{-7}$ cc/sec from the leak test.

• Childhood Kidney Diseases
• /
• v.7 no.1
• /
• pp.9-15
• /
• 2003

Purpose : Several studies have suggested that hyperlipidemia might be a causative factor contributing to the progression of initial glomerular injury through the development of glomerulosclerosis. We examined the potential beneficial effect of atorvastatin - which blocks the rate limiting step of cholesterol synthesis by inhibiting HMG-CoA reductase - in PAN-induced nephrosis. Materials and Methods : Glomerulosclerosis was induced in Sprague-Dawley male rats by repeated administration of PAN. Sprague-Dawley male rats were divided into 3 groups : group I(control), group II(PAN 20 mg/kg, subcutaneous injection), group III(PAN 20 mg/kg subcutaneous injection and atorvastatin 50 mg/kg/day per oral). On the 11th week, upon sacrifice of the experimental animals, blood sampling, 24-hr urine collection and nephrectomy were performed. Results : Group III had significantly lower BUN and higher serum albumin($30.9{\pm}17.2\;vs.\;17.3{\pm}2.5\;mg/dL;\;2.3{\pm}0.1\;vs.\;2.5{\pm}0.2\;g/dL$, P<0.05) compared with group II. In the lipid profiles, group III was associated with a reduction in total cholesterol and LDL($291{\pm}173\;vs.\;167{\pm}72\;mg/dL:\;57{\pm}53\;vs.\;27{\pm}12\;mg/dL$, P>0.05) compared with group II. Atorvastatin administration lowered the glomerular sclerosing index significantly(26.2% vs. 13.3%, P<0.05). Conclusion : Puromycin-induced glomerulosclerosis could be ameliorated by the reduction of hyperlipidemia with atorvastatin. This suggests that hyperlipidemia contributes to the pathogenesis of glomerulosclerosis.

• Resources Recycling
• /
• v.32 no.6
• /
• pp.10-17
• /
• 2023

Calcium silicate cement (CSC) is an environmentally sustainable, low-carbon cement and has garnered significant attention in recent studies. However, the pre-curing step required to activate the carbon dioxide reaction and to handle the sample. This study aimed to examine the viability of extending the application of CSC without pre-curing by enhancing initial strength by mixing calcium sulfoaluminate (CSA) fast-hardening cement into CSC. The investigation assessed changes in compression strength and Q-XRD mineral characteristics concerning variations in the mixing ratio of CSC and CSA fast-hardening cement within a carbon dioxide atmosphere. The compressive strength results indicated that the 3-day and 7-day strengths were 14.18 MPa and 22.98 MPa, respectively, under the 50% CSC condition, meeting the type 1 cement KS standard. Mineral characteristics analysis revealed an increase in calcite mineral, a byproduct of the carbon dioxide reaction, contributing to strength enhancement. Even after seven days, substantial quantities of unreacted rankinitene and pseudowollastonite were observed, as well as dicalcium silicate and yeelimite, which are hydrated minerals. This observation was confirmed the possibility of strength improvement after 7 days.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.672-675
• /
• 2005

To imprint 70-nm wide line-patterns, we used a newly developed ultraviolet nanoimprint lithography (UV-NIL) process in which an elementwise patterned stamp (EPS), a large-area stamp, and pressurized air are used to imprint a wafer in a single step. For a single-step UV-NIL of a 4' wafer, we fabricated two identical $5'\times5'\times0.09'(W{\times}L{\times}H)$ quartz EPSs, except that one is with nanopatterns and the other without nanopatterns. Both of them consist of 16 small-area stamps, called elements, each of which is $10\;mm\;\times\;10\;mm$. UV-curable low-viscosity resin droplets were dispensed directly on each element of the EPSs. The volume and viscosity of each droplet are 3.7 nl and 7 cps. Droplets were dispensed in such a way that no air entrapment between elements and wafer occurs. When the droplets were fully pressed between ESP and wafer, some incompletely filled elements were observed because of the topology mismatch between EPS and wafer. To complete those incomplete fillings, pressurized air of 2 bar was applied to the bottom of the wafer for 2 min. Experimental results have shown that nanopatterns of the EPS were successfully transferred to the resin layer on the wafer.

• Journal of Digital Convergence
• /
• v.18 no.9
• /
• pp.211-219
• /
• 2020

This study was conducted to investigate the effects of communication competence and interpersonal understanding on empathy of nursing students who have experienced fundamental nursing skills course. The subjects of this study were 122 second-year nursing students in a university. Data were collected using a questionnaire from September to December 2018. The data were analyzed by descriptive statistics, correlations and hierarchical regression using the SPSS 22.0 program. Factors affecting empathy were active participation in the practice, communication skills, and understanding of interpersonal. Therefore, In order to improve the empathy of nursing students, it is necessary to introduce a step-by-step empathy education program into the curriculum that can contribute to establishing a device that can induce active participation in practice and contribute to communication and interpersonal relationships.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.222-228
• /
• 2005

Undoped GaN epitaxial layer was grown on c-plane sapphire substrate by a two-step growth with metalorganic chemical vapor deposition(MOCVD). We have investigated the effects of the variation of final growth temperature on surface morphology, roughness, crystal quality, optical property, and electrical property In a horizontal MOCVD reactor, the film was grown at 300 Tow low-pressure with a fixed nucleation temperature of $500^{\circ}C$, varing the final growth temperature from $850\~1050^{\circ}C$ . The undoped GaN epilayers were characterized by atomic force microscopy, high-resolution x-ray diffractometer, photoluminescence, and Hall effect measurement.

• Composites Research
• /
• v.34 no.5
• /
• pp.269-276
• /
• 2021

PCM (Prepreg Compression Molding) process is a high-speed molding technology that can manufacture high-quality CFRP (Carbon Fiber Reinforced Plastic) parts. Compared to the autoclave process, it generates less waste and can significantly reduce cycle time, so various studies are being conducted in the aerospace and automobile industries. In this study, in order to improve the quality of the PCM process, a molding method was developed to increase the compression pressure of the press step by step according to the curing behavior of the prepreg. It was confirmed that this multi-stage compression molding technology is a good means to produce high-quality CFRP products and shorten cycle times. And, the laminated prepreg at room temperature was immediately put into the mold and preheated and molded at the same time, so that it could be molded without a separate preheating process. In addition, as a result of applying the same process conditions optimized for flat plate molding to three-dimensional shapes, a product similar to a flat plate in appearance could be made without the process of establishing process conditions.

• Journal of Powder Materials
• /
• v.22 no.1
• /
• pp.10-14
• /
• 2015

In recent years, industrial demands for superior mechanical properties of powder metallurgy steel components with low cost are rapidly growing. Sinter hardening that combines sintering and heat treatment in continuous one step is cost-effective. The cooling rate during the sinter hardening process dominates material microstructures, which finally determine the mechanical properties of the parts. This research establishes a numerical model of the relation between various cooling rates and microstructures in a sinter hardenable material. The evolution of a martensitic phase in the treated microstructure during end quench tests using various cooling media of water, oil, and air is predicted from the cooling rate, which is influenced by cooling conditions, using the finite element method simulations. The effects of the cooling condition on the microstructure of the sinter hardening material are found. The obtained limiting size of the sinter hardening part is helpful to design complicate shaped components.

• Journal of the Korean Chemical Society
• /
• v.41 no.6
• /
• pp.299-303
• /
• 1997

The rate constants($k_{OH}$) for the alkaline hydrolysis of the 4-substituted phenyl ethyl benzylphosphonates were determined in various buffer solutions by UV(Vis spectrophotometer. The activation entropies of the title reactions show negative values and this result is not consistent with a dissociative mechanism (EA) for which a positive or slightly negative value of the entropy of activation should be expected. An associative mechanism(AE) is favorable because the negligible negative charge is generated on the leaving group in the rate determining step from a good Hammett relationship(ρ=1.89). By the results of a kinetic study, we conclude that a dissociative mechanism is not proceeded in the title reactions.