• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1155-1165
• /
• 1990

A new method of predicting effect of rolling parameters on roll pressure, roll force, and power and energy consumptions in hot strip rolling is presented. The method is based on approximate solutions for velocity, strain rate, and stress distributions in the roll gap. The degree of approximation was examined by the finite element solutions. The theoretical predictions were compared with experimental data from hot rolling of steel strip and steel plate.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1010-1014
• /
• 2001

A severe strip vibration in continuous galvanizing line facilities of the steel companies has sometimes occurred due to the exceeding wearing of the roll bush and bearing. This vibration brings on the lack of uniform coating thickness in steel plate. As a result, the total maintenance and product costs in this factory are increased by the shortage of operation time for the replacement of bush, bearings and these components. In this study, the vibration characteristics of this strip are investigated by the FEM using ANSYS. Also the vibration measurement of strip and its structure performed by the laser Doppler vibrometer(LDV) and accelerometers are compared to theoretical analysis results.

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.60-61
• /
• 1997

• Journal of Korea Foundry Society
• /
• v.25 no.3
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.4
• /
• pp.37-44
• /
• 2012

This paper describes large scale pullout test results, in order to evaluate extensibility effect of strip-type reinforcement. The same test for ribbed steel strip reinforcement also is conducted to compare the friction resistance reinforcements' evaluation results. The pullout resistance of the ribbed steel strip reinforcement, which has a small cross sectional areas, was better than the friction resistance reinforcements' due to the bearing (passive) resistance. In case of friction resistance reinforcements, the pullout resistance of extensible reinforcement was better than inextensible reinforcement' even though they have a similar cross sectional areas.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.6
• /
• pp.518-523
• /
• 2005

Strip off-center is one of the major problems in hot strip mill line. The key to good centering is having good equipment, modern control systems, excellent maintenance and an understanding of milling process. Therefore, this study aims to develop a system that is useful for quantitative analysis of strip off-center. In this study, the measuring method of strip off-center was thoroughly studied and the exclusive control board to line scan camera were designed. Also, the manipulated type housing for line scan camera was developed to adjust initial parameters for strip width and center line. In order to check the accuracy and usefulness of the developed system, FM stand in $\#2$ Hot Strip Factory in Pohang Steel Works was targeted.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1412-1416
• /
• 2003

Induction Heaters are commonly used in heating steel strip product, because it can rapidly and efficiently heat steel strip/bar. In this study, a inductive heating model is developed and the predictions are compared with measured temperatures. The temperatures are measured from POSCO thin-slab rolling facility (so called Minimill). Induction heater is installed between reduction unit and holding furnace This induction heater raise the temperature of steel bars from $930^{\circ}C$ to about $1100^{\circ}C$ which gives the required temperature for finishing mill process after holding period at holding furnace. Unlike other simple equation models, this model allows us to predict temperature profiles of sections of steel bars.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.145-152
• /
• 2004

The flow stress value was calculated by comparing predicted and measured roll force. Using basic on-line roll force model and logged mill data the flow stress equation of high strength steel for automobile was derived. The flow stress equation consists of the flow stress equation of carbon steel and flow stress factor calculated by neural network with input parameters not only carbon contents, strip temperature, strain, and strain rate, but also compositions such as Mn, p, Ti, Nb, and Mo. Using the flow stress equation and basic roll force model, precision roll force model of high strength steel for automobile was derived. Using test set of logged mill data the flow stress equation was verified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.3
• /
• pp.327-335
• /
• 2015

In this paper, we propose an independent cooling control (ICC) scheme for high strength and atmosphere corrosion resisting steel to obtain the desired temperature and properties along the longitudinal direction of the steel in the run-out table (ROT) process. A temperature model of the independent process is developed to divide the ROT into front and back sections. The control concept uses field data, problem analysis, and a time-temperature transformation diagram. The effectiveness of the proposed control is verified using simulation results under a temperature disturbance by the transformation in the middle of the ROT. The results of a hot strip mill field test show that the temperature control performance is significantly improved by the proposed control scheme.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.1
• /
• pp.41-52
• /
• 2001

In this paper the analysis of laminate composite folded plates with arbitrary angle connection like box girder is studied by finite strip method Total stiffness of laminated plate is obtained by integration of the stiffness in each layer or lamina through laminate thickness and total stiffness in each layer or lamina through laminate thickness and total tiffness matrix is obtained by substitutionto equilibrium equation derived from the minimum total potential energy theorem. The assumed displacement functions for a finite strip method in plate or box girder analysis are combinations of one-way polynomial functions in the transverse direction and harmonic functions in the span-wise direction. Finite strip method with the merits of the simplification in modeling and the reduction of analytical time is accurate in the analysis of laminate composite folded plates shaped like box firders.