• Journal of the Korean Institute of Gas
• /
• v.7 no.2 s.19
• /
• pp.48-53
• /
• 2003

This study is to look at the effect for deformation of carbon steel for high-presure pipe, on the AE signals produced by tensile test. Acoustic emission(AE) has been widely used in various fields because of its extreme sensitivity, dynamic detection ability and location of growing defects. We investigated a relationship failure mode and AE signals by tensile test, From the tensile test, we could divide into four ranges of the failure modes of elastic range, yield range, plastic range before $\sigma$u, plastic range after $\sigma$u. And failure behaviors of elastic range, yield range, plastic range before $\sigma$u, plastic range after $\sigma$u could be evaluated in tensile test by AE counts, accumulation counts and time frequency analysis. It is expected to be basic data that can protect a risk according to tensile test and bending of pipe material for pressure vessel, as a real time test of AE.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.184-191
• /
• 2000

In this research, a numerical model is developed for analysis of buried pipelines considering longitudinal permanent ground deformation(PGD) due to liquefaction induced lateral spreading. Buried pipelines and surrounding soil are medeled as continuous pipelines using the beam elements and a series of elasto-plastic springs uniformly distributed along the pipelines, respectively. Idealized various PGD patte군 based on the observation of PGD are used as a loading configuration and the length of the lateral spread zone is considered as a loading parameter. Numerical results are verified with other research results and efficient applicability of developed procedure is shown. Analyses are performed by varying different parameters such as PGD pattern, pipe diameter and pipe thickness. Results show that response of buried pipelines are more affected by pipe thickness than pipe diameter. Finally, the critical length of the lateral spread zone and the critical magnitude of PGD which cause yielding, local buckling or tension failure are proposed for the steel pipe which are normally used in Korea.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.3
• /
• pp.47-49
• /
• 2008

The brake pipe is important part in automobile. The brake pipe have to prevent crack, fracture and defects for braking in safety. Especially, shape of ends of pipe has influence on ability of brake. Based on the procedure of process design, in this paper, the forming operation is designed by finite element method. Design variable and response value was selected shape of die and damage factor. To improve die that performed FEM and compared results of two types of die.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.1
• /
• pp.59-66
• /
• 2015

In this study, structural stability of large diameter high density polyethylene (HDPE) pipe during installation was numerically investigated in order to investigate the effect of concrete collar dimension, water depth and tension (pulling force). From the numerical simulation results, the total stress of HDPE pipe with designed concrete collar was within 2.5%, so the total weight of concrete collar for sinking of HDPE is important rather than concrete collar dimension. Furthermore, the tension area for possible installation is decreased as the air filling rate is increased. Therefore, it is important to calculate the reasonable tension range before actual installation for safe installation of HDPE pipe.

• Journal of the Korean Society of Safety
• /
• v.16 no.1
• /
• pp.59-64
• /
• 2001

Even though there is a guideline for the required strength of pipe support in inspection, it does not mean the nominal strength which can be used for the form work design. And, Concrete Specification defines that the pipe support should be designed according to the steel design guidelines but the design details are not provided, such as buckling length and the sectional modulus, etc. For the better prediction of strength of pipe support, the slenderness ratio of support which reflects the boundary condition should be considered. In this paper, the elastic buckling formula based on the slenderness is derived. The formula contains the strength reduction factor that consider the strength deduction caused by initial lateral deformation and is 0.65 consistently regardless of boundary conditions. And the coefficient of effective buckling length is calculated from the experiment.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.41-46
• /
• 2002

Recently, the design and construction of massive concrete structures are increased, But, the temperature rise within a large concrete mass makes the construction of massive concrete structures be very difficult. Therefore, various techniques of the thermal stress control of the mass concrete have been widely used. One of them is pipe-cooling which reduces the temperature of concrete with flowing water. It was shown to be possible to construct the massive concrete foundation of urban bridge successfully by application of pipe-cooling system with steel pipe and water circulation. It was also found to expected to make it possible to reduce the probability of thermal crack development in a massive concrete foundation of urban bridge by pipe-cooling system.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.6
• /
• pp.111-116
• /
• 2009

The cracking due to hydration heat in mass concrete must be resolved to improve the stability and durability of concrete structures. In this study, the economic efficiency was improved by replacing a copper pipe with a steel one for the heat pipe, and the heat pipe was standardized to significantly improve the operation efficiency, such as the processing, transport, assembly, and construction time. As a result of the experiment, the peak temperature of the ICSHP, ISSHP, and ISUHP specimens decreased by about $7.2{\sim}10.9^{\circ}C$ compared to the OPC specimen and the probability of a thermal crack being generated in the ICSHP, ISSHP, and ISUHP specimens decreased by up to 84~88%.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.488-493
• /
• 2003

This paper presents new skill in tube-mill processing getting the increase in production efficiency and quality in response to the recent request of high grade pipe. In this study, researchers developed the method to improve the precision of pipe and tool life in tube-mill processing. Optimum tool shape is devised by analyzing various simulation and mechanism in cutting process. In order to verify the confidence of the proposed machining technology, it is applied to the real processing machinery in the field.

• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.176-181
• /
• 2016

The exhaust tail pipe is the only visible part of the exhaust system on a vehicle. The conventional way to make the tail pipe is welding after stamping. There are various problems that occur during the stamping of stainless steel sheets such as scratching and local fracture. Problems during welding can also occur due to poor weldability. Tube hydroforming can be a solution, which eliminates these problems. The current study deals with the development of tube hydroforming for a vehicle tail pipe using finite element analysis for a free-feeding method. The current study focuses on the development of a proper load path for the tail pipe hydroforming and how bending influences the subsequent processing steps. The FE analysis results were compared with experimental results. This study shows the importance of bending and the necessity of considering bending when performing a tube hydroforming analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.27-28
• /
• 2006

This study performs to investigate deformation of wall thinning pipe and to find out the position of the internal thinning defect by shearography. Shearography is one of optical methods those have applied to nondestructive testing (NDT) and the strain/stress analysis. This technique has the merit of the directly measuring the first derivative of displacement, sensitivity of which can be adjusted by the handling of optical component in interferometer. In this paper, we tested carbon steel pipe locally wall thinned and loaded internal pressure and developed the nondestructive out-of-plane deformation analysis technique fur internal thinning defect of elbow by shearography. From the results, it was confirmed that this technique is proper to the practical application on the pipe line system with internal defect.