• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.519-526
• /
• 1997

The purpose of this study is to develop the analytical model for the reinforcement bar connection in group-filled steel pipe sleeve, which consists of beam elements for the reinforcement bar and shell elements for the sleeve and the mortar and spring elements for the bond stress-slip relationship. In the reinforcement bar connection using grout-filled steel pipe sleeve, the major variables are the bond stiffness between reinforcement bar and mortar($K_1$) and between sleeve and mortar($K_2$). It is nearly difficult to predict the exact bond stiffness with the experimental results. Therefore, The linearly elastic analyses using ABAQUS, FEM package show the validity of the mathematical equations for the bond stiffness and the choice of material elements in this paper. To predict the behaviour between yield and ultimate tensile strength, the nonlinear analyses must be performed henceforth.

• Steel and Composite Structures
• /
• 제23권1호
• /
• pp.95-105
• /
• 2017

The use of superelastic shape memory alloys (SMAs) as reinforcements in concrete structures is gradually gaining interest among researchers. Because of different mechanical properties of SMAs compared to the regular steel bars, the use of SMAs as reinforcement in the concrete may change the response of structures under seismic loads. In this study, the effect of SMAs as reinforcement in concrete structures is analytically investigated for 3-, 6- and 8-story reinforced concrete (RC) buildings. For each concrete building, three different reinforcement details are considered: (1) steel reinforcement (Steel) only, (2) SMA bar used in the plastic hinge region of the beams and steel bar in other regions (Steel-SMA), and (3), beams fully reinforced with SMA bar (SMA) and steel bar in other regions. For each case, columns are reinforced with steel bar. Incremental Dynamic Analyses (IDA) are performed using ten different ground motion records to determine the seismic performance of Steel, Steel-SMA and SMA RC buildings. Then fragility curves for each type of RC building by using IDA results for IO, LS and CP performance levels are calculated. Results obtained from the analyses indicate that 3-story frames have approximately the same spectral acceleration corresponding with failure of frames, but in the cases of 6 and 8-story frames, the spectral acceleration is higher in frames equipped with steel reinforcements. Furthermore, the probability of fragility in all frames increases by the building height for all performance levels. Finally, economic evaluation of the three systems are compared.

• 보존과학회지
• /
• 제31권4호
• /
• pp.477-488
• /
• 2015

본 연구에서는 석조문화재에 대한 금속보강재의 최소 개입을 통해 원형부재의 이차 훼손을 줄이고, 동시에 최대의 구조보강 효과를 얻을 수 있도록 제안된 실험을 통해 처리기술의 객관적 기준을 다음과 같이 설정하였다. 첫째, 금속보강재의 설계 기준은 석조문화재의 풍화도에 따라 보강재비의 산정이 이루어져한다. 둘째, 석조문화재의 원형이 부분적으로 훼손되어 형태나 구조적으로 보강이 필요할 때 보형처리(구부재 + 신석재 접합)는 풍화등급이 높은 부재를 기준으로 금속보강재 비율을 계획해야 한다. 본 연구를 바탕으로 석조문화재의 구조적인 안정을 꾀할 수 있는 조건을 고려한 금속보강재 비율을 풍화영역별로 제시하면, 접합단면 대비 $800kgf/cm^2$ 이하는 0.13~0.23, $800kgf/cm^2$ 이상 $1200kgf/cm^2$ 이하는 0.24~0.28, $1200kgf/cm^2$ 이상은 0.29~0.5의 금속보강재비를 권장할 수 있다. 특히 더욱 세분화된 풍화등급에 따른 금속보강재의 적용 여부는 석조물의 파괴계수와 금속보강재의 물성을 고려하여야 할 것으로 사료된다.

• 한국건축시공학회지
• /
• 제8권1호
• /
• pp.83-90
• /
• 2008

The reinforcing steel process is composed of the development of placing drawing, cutting and bending, and the placement and fabrication of the reinforcement, and is participated in by reinforcement detailer, the fabricator and placer. Because the reinforcing steel process-from estimating and rebar detailing, to production, material tracking, billing, and general accounting-is conducted by many participant, reinforcement details based on building code and reinforcing bar detailing standards are essential. The process, however, holds some problems. Building code has been revised recently, and the utilization of placing drawings was proved to be low, and the reinforcement estimating in early stage of the process is below what is required for placement. Therefore, in this study, a survey was conducted to the reinforcement detailer, the fabricator and placer of domestic construction industry. According to the analysis of the survey, the reinforcement details on site was not standardized. The improvement in reinforcing steel detailing standards was sought by analyzing the results of the survey including reinforcement constructability.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.13-16
• /
• 2008

철근으로 휨 보강된 일반적인 부재의 경우, 강도설계법으로 부재의 공칭 휨 강도를 계산할 때 모든 휨 인장 철근은 극한상태에서 항복한다고 가정한다. 따라서 인장력은 철근의 도심에 작용하고 인장 철근 단면적과 철근의 항복강도의 곱으로 표현될 수 있다. 그러나 FRP bar는 철근과 달리 항복거동을 보이지 않기 때문에 각 열 FRP bar에 작용하는 응력은 중립축에서 떨어진 거리에 따라 달라질 것이다. 게다가 서로 다른 종류의 FRP bar가 동시에 한 부재에 적용된다면, 각 FRP bar의 변형률에 따라 작용하는 응력 또한 다양하게 될 것이고, 거동 양상 역시 예상과 다르게 나타날 것이다. 이에 본 연구에서는 일반철근, CFRP bar, GFRP bar를 이용하여 하이브리드 휨 보강된 6개의 고강도 콘크리트 보를 제작하고 구조실험을 실시하였다. 실험 결과 하이브리드 보강된 부재는 FRP bar로 단순 보강된 부재의 낮은 강성, 큰 균열폭, 취성 문제를 상당히 보완시켜주는 것으로 나타났다.

• Architectural research
• /
• 제22권1호
• /
• pp.33-39
• /
• 2020

In this study, side-face blowout failure strength of high strength headed reinforcing bar, which is vertically anchoring between RC or SFRC members, is evaluated throughout pullout test. The major test parameters are content ratio of high strength steel fibers, strength of rebar, length of anchorage, presence of shear reinforcement, and the side concrete cover thickness planned to be 1.3 times of the rebar. In pullout test, tensile force was applied to the headed reinforcing bar with the hinged supports positioned 1.5 and 0.7 times the anchorage length on both sides of the headed reinforcing bar. As a result, the cone-shaped crack occurred where the headed reinforcing bar embedded and finally side-face blowout failure caused by bearing pressure of the headed reinforcing bar. The tensile strength of specimens increased by 13.0 ~26.2% with shear reinforcement. The pullout strength of the specimens increased by 3.6 ~15.4% according to steel fiber reinforcement. Increasing the anchoring length and shear reinforcement were evaluated to reduce the stress bearing ration of the total stress.

• 한국지반신소재학회논문집
• /
• 제6권3호
• /
• pp.31-37
• /
• 2007

국외 수입에 의존하고 있는 띠형 강판 보강재를 대체할 수 있는 새로운 강(steel) 보강재로서, 강판과 지지부재를 결합한 새로운 형태의 보강재를 고안하였다. 개발 보강재는 폭${\times}$두께가 $65mm{\times}4.5mm$인 띠형 강판에 50cm 간격으로 11mm 직경의 천공구멍 및 돌기가 형성된 형태를 가지고 있으며, 인발저항력 증대를 위한 지지부재의 설치가 가능하다. 개발 보강재의 마찰특성 평가를 위한 전단마찰시험 및 인발시험 결과, 지지부재를 설치하면 보강재의 인발저항력이 크게 증가하는 것으로 나타났다.

• 한국건설순환자원학회논문집
• /
• 제3권2호
• /
• pp.159-164
• /
• 2015

This paper presents results on a study of the Rayleigh wave scattering in concrete with a steel bar using transient elastic waves. To study the characteristics of the scattered waves induced by a steel bar in concrete, a three-dimensional finite element method was adopted. A case for elastic wave propagation parallel to the steel bar is discussed. The effect of the cover thickness and steel bar diameter on the Rayleigh wave was studied. To confirm the numerical investigations, a concrete specimen containing a steel bar was made, and corresponding transient elastic wave experiments were conducted. It is believed that the result of this study can serve as an important reference in a nondestructive evaluation of concrete with a steel bar.

• 한국농공학회논문집
• /
• 제46권1호
• /
• pp.41-51
• /
• 2004

FRP re-bar in concrete structures could be used as a substitute of steel re-bars for that cases in which aggressive environment produce high steel corrosion, or lightweight is an important design factor, or transportation cost increase significantly with the weight of the materials. But FRP fibers have only linearly elastic stress-strain behavior; whereas, steel re-bar has linear elastic behavior up to the yield point followed by large plastic deformation and strain hardening. Thus, the current FRP re-bars are not suitable concrete reinforcement where a large amount of plastic deformation prior to collapse is required. The main objectives of this study in to evaluate the tensile behavior and the fracture mode of hybrid FRP re-bar. Fracture mode of hybrid FRP re-bar is unique. The only feature common to the failure of the hybrid FRP re-bars and the composite is the random fiber fracture and multilevel fracture of sleeve fibers, and the resin laceration behavior in both the sleeve and the core areas. Also, the result of the tensile and interlaminar shear stress test results of hybrid FRP re-bar can provide its excellent tensile strength-strain and interlaminar stress-strain behavior.

• Computers and Concrete
• /
• 제18권3호
• /
• pp.337-354
• /
• 2016

To study the influence on fracture properties of reinforced concrete wedge splitting test specimens by the addition of reinforcement, and the restriction of steel bars on crack propagation, 7 groups reinforced concrete specimens of different reinforcement position and 1 group plain concrete specimens with the same size factors were designed and constructed for the tests. Based on the double-K fracture criterion and tests, fracture toughness calculation model which was suitable for reinforced concrete wedge splitting tensile specimens has been obtained. The results show that: the value of initial craking load Pini and unstable fracture load Pun decreases gradually with the distance of reinforcement away from specimens's top. Compared with plain concrete specimens, addition of steel bar can reduce the value of initial fracture toughness KIini, but significantly increase the value of the critical effective crack length ac and unstable fracture toughness KIun. For tensional concrete member, the effect of anti-cracking by reinforcement was mainly acted after cracking, the best function of preventing fracture initiation was when the steel bar was placed in the middle of the crack, and when the reinforcement was across the crack and located away from crack tip, it plays the best role in inhibiting the extension of crack.