• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.4
• /
• pp.42-49
• /
• 1997

A conventional adaptive noise canceller (ANC) using LMS algorithm suffers from the misadjustment of adaptive filter weights due to the gradient-estimate noise by input speech signal at steady state. In this paper, an ANC is proposed which uses the combination of VSLMS (variable step size LMS) and SA (sign algorithm) to improve steady state performance and convergence rate. SA algorithm is applied in speech region to prevent the weights from perturbing by output speech of ANC and VSLMS algorithm is applied to improve convergence rate and channel tracking ability in silence region and adaptive transient region. In compute rsimulation, the performance of the proposed VSLMS-SA combination algorithm is much better than LMS algorithm and the algorithm, recently proposed by greenberg, with adaptation step-size parameter determine dby sum method in convergence rate, channel tracking and steady state performance.

• Journal of Industrial Technology
• /
• v.15
• /
• pp.203-208
• /
• 1995

This paper suggests the three dimensional steady state searching techniques of hard disk/head system, which has some skew angle with flexure. In order to analyze the steady state behaviors of magnetic head slider, the localized Knudsen number and the localized bearing numbers are sued. For finding the steady state of magnetic head slider under the pre-loaded condition, I proposed multi-dimensional Newton-Raphson method which traces the equilibrium position of magnetic head slider, which has 3-degrees of freedom, using Jacobian matrix. The multi-dimensional Newton-Raphson method is very efficient technique for finding the steady state position of magnetic head slider because it approaches to the equilibrium position with changing three parameters simultaneously.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.96-101
• /
• 2000

In this paper, an experimental investigation of characteristics of developing transitional steady flows in a square-sectional 180 urved duct is presented. The experimental study is carried out to measure axial velocity profiles by using Laser Doppler Velocimeter (LDV) system. The flow development is found to depend upon Dean number and curvature ratio. For transitional steady flows, the maximum velocity position of axial velocity profiles begins to incline toward the outer wall from $\phi$=$30^{\circ}$bended angle, velocity profiles in center of the duct have lower value than those of the inner and outer walls because of the centrifugal forces.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.6
• /
• pp.880-885
• /
• 2000

Flow patterns and steady flow characteristics of an intake 3valve cylinder head are not obviously declared. Thus, in the study, the characteristics and limitation of intake flow coefficient which applied to multi intake valve engine are introduced. The flow coefficient and tumble characteristics are investigated by means of the steady flow test and flow visualization method. As the results, it is found that the intake flow rate is dominated by effective valve open area. In addition, this paper shows that the mass flow rate of intake 3valve engine is greater than that of intake 2valve engine and tumble flow of intake 3valve engine is superior to that of intake 2valve engine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.33-39
• /
• 1999

In this paper an experimenatal investigation of characteristics of developing ransitional steady flows in a square-sectional $180^{\circ}$ curved duct is presented, The experimental study is carried out to measure axial velocity profiles secondary flow velocity profiles and entrance length by using Laser Dopper Velocimeter(LDV) system. The flow development is found to depend upon Dean number and curvature ratio. Of special interest is the secondary flow generated by centrifugal effects in the plane of the cross-section of the duct. The secondary flows becomes strong from $120^{\circ}$ of bended angle on the duct. The entrance length of transitional steady flow is obtained to $120^{\circ}$ of bended angle of the duct in this experimental conditions.

• Management Science and Financial Engineering
• /
• v.16 no.1
• /
• pp.119-135
• /
• 2010

In this paper, we readdress the optimization problem for minimizing the inspection cost in a back-light unit inspection system, which forms a network including a K-stage inspection system, a source inspection shop, and a re-inspection shop. In order to formulate our objective function when the system is in a steady state, assuming that the number of nonconforming items in a lot follows a binomial distribution when a lot is formed for inspection, we make a steady-state network flow analysis between shops, and derive the steady-state amount of flows between nodes and the steady-state fraction defectives by solving a nonlinear balance equation. Finally we provide some fundamental properties and an enumeration method for determining an optimal value of K which minimizes our objective function. In addition, we compare our results numerically with previous ones.

• Journal of the Korean Society of Combustion
• /
• v.5 no.1
• /
• pp.1-6
• /
• 2000

Surface reaction occurs at a certain surface temperature when a catalyst is heated up in a reactive mixture. If homogeneous ignition does not occur, a steady state is observed because the heat produced by the surface reaction is balanced with the heat loss caused by convection, conduction and radiation. The present paper treats the effects of pressure on the surface temperature at the steady state. Hydrogen and oxygen are used as reactants and nitrogen as an inert gas. A spherical platinum catalyst of 1.5 mm in diameter is sustained in the chamber with two wires of 0.1 mm in diameter. As results, there exists a maximum steady temperature at a certain relative hydrogen concentration which increases with total pressure. At the steady state, it can be approximated that the heat release is estimated by the mass transfer considering the effect of natural convection. The experimental results are explained qualitatively by the approximation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.827-830
• /
• 2011

The equation of motion for the piping system conveying harmonically pulsating fluid is presented. When pulsating fluid flows, the properties of this system like mass, stiffness and damp is changing according to fluid fluctuation. To solve the steady-state time response of this system, numerical integration method of differential equation was usually used. But this method has some problem such time consuming method and difficulty of converging. Therefore this research suggests reliable and efficient numerical method to solve steady-state time response of piping system by using displacement assumption method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.89-102
• /
• 1997

In this study, the steady state cornering behavior of a vehicle is investigated by using a numerical model that has parameters associated with roll motion. The nonlinear characteristics of tire cornering forces and aligning torques are presented in analytical forms using the magic formula. The sets of nonlinear algebraic equations that govern the cornering motion are solved by the Newton-Raphson iteration method. The vehicle design parameters are measured by SPMD(Suspension Parameter Measuring Device), and its results are verified by carrying out a skid pad test. The design parameters that are most affecting the steady state cornering behavior are classified into four factors, and the contributions of the factors to understeer gradient are then calculated.

• Wind and Structures
• /
• v.8 no.5
• /
• pp.373-388
• /
• 2005

Quasi-steady approaches have been often adopted to model wind forces on moving cylinders in cross-flow and to study instability conditions of rigid cylinders supported by visco-elastic devices. Recently, much attention has been devoted to the experimental study of inclined and/or yawed circular cylinders detecting dynamical phenomena such as galloping-like instability, but, at the present state-of-the-art, no mathematical model is able to recognize or predict satisfactorily this behaviour. The present paper presents a generalization of the quasi-steady approach for the definition of the flow-induced forces on yawed and inclined circular cylinders. The proposed model is able to replicate experimental behaviour and to predict the galloping instability observed during a series of recent wind-tunnel tests.