• Journal of the Korean Wood Science and Technology
• /
• 제49권4호
• /
• pp.315-327
• /
• 2021

본 연구에서는 제재부산물인 톱밥과 농업부산물인 왕겨의 이용방안을 검토하고자 친환경재료인 숯을 첨가하여 밀도별, 혼합비율별로 혼합보드를 제조하고 휨성능을 조사하여 다음과 같은 결과를 얻었다. 톱밥과 왕겨 및 숯의 첨가율을 50:20:20, 수지첨가율을 10%로하여 밀도별로 제조한 혼합보드의 밀도가 0.5 g/cm³에서 0.7 g/cm³로 증가할수록 휨강도는 0.42~3.24 N/mm², 동적탄성계수는 94.5~888.4 N/mm² 그리고 정적탄성계수는 31.4~220.7 N/mm²의 범위를 나타내, 밀도가 증가할수록 휨성능이 증가하여 밀도가 휨성능에 크게 영향을 끼쳤다. 밀도 0.6 g/cm³, 톱밥첨가율을 50%로 하고, 왕겨와 숯의 첨가율을 달리하여 제조한 보드에서 숯의 첨가율이 증가할수록 휨성능이 감소하는 경향을 나타냈다. 왕겨 및 숯의 첨가율과 휨강도, 공진주파수, 동적 및 정적 휨 탄성계수사이의 관계는 결정계수의 값(R²)은 각각 0.4562, 0.4310, 0.4589, 0.5847으로 다소 낮은 상관관계를 나타내 첨가율이 휨성능에 끼치는 영향은 적은 것을 알 수 있었다.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.1-12
• /
• 2015

The current scenario of the transportation sector reflects the urgent need to address issues such as depletion of traditional fuel reserves and ever growing pollution levels. Researchers around the world are focussing on alternatives as well as optimisation of currently employed devices to reduce the pollution levels generated by the commonly used fuels. One such optimisation involves the study of air flow within the intake manifolds of SI engines. It is a well-known fact that alterations in the air manifolds of engines have a significant impact on the engine performance parameters, fuel consumption and emission levels. Previous works have demonstrated the impacts of runner lengths, diameter, plenum volume, taper angle of distribution manifolds and other factors on in-cylinder fluid motion and engine performance. However, a static setup provides an optimal configuration only at a specific engine speed. This paper aims to investigate the variations in the same parameters on a four stroke, naturally aspirated single cylinder SI engine through varying the cross section design over the intake runner with the aid of Computational Fluid Dynamics. The system consists of segments that form the intake runner with projections on the inside that allow various permutations of the intake runner segments. The various configurations provide the optimised fluid flow characteristics within the intake manifold at specific engine speed intervals. The variations such as turbulence, air fuel mixing are analysed using the three dimensional CFD software FLUENT. The results can be used further for developing an automated or manually adjustable intake manifold.

• Korean Chemical Engineering Research
• /
• 제56권6호
• /
• pp.864-870
• /
• 2018

고체 수송관(standpipe, 내경 0.025 m)으로 연결된 2 단 기포 유동층(내경 0.1 m, 높이1.2 m)에서 붕괴 속도에 대한 하단 층 높이의 영향을 조사하였다. 기체로는 공기를 사용하였고, 고체로는 입도가 큰 입자(< $1000{\mu}m$, 겉보기 밀도 $3625kg/m^3$)와 입도가 작은 입자(< $147{\mu}m$, 겉보기 밀도 $4079kg/m^3$)를 혼합한 입자를 사용하였다. 작은 입자의 혼합비, 하단 유동층의 층 높이, 상단 유동층 분산판을 실험 변수로 고려하였다. 붕괴 속도는 하단 유동층의 정체 층 높이가 증가할수록 증가하였다. 그러나 작은 입도의 혼합비가 증가하면 이 효과가 감소하였다. 이 효과는 층 높이 증가에 따른 고체 수송관 압력 강하의 증가 때문이 아니라, 수송관 출구를 막는 농후상 굵은 입자 층 높이의 증가 때문으로 보였다. 상단 유동층 분산판 압력 강하의 증가는 붕괴 속도를 조금 감소시켰다. 붕괴 속도를 예측하는 개선된 상관식을 제안하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권4호
• /
• pp.11-22
• /
• 2023

본 연구에서는 원심성형 기법을 이용하여 구조용 콘크리트 각형보를 개발하였으며, 단면의 휨 강성을 확보하기 위하여 단면의 중 공률은 10 % 이하로 하며 이를 위하여 기존의 빈배합상태의 콘크리트가 아닌 고슬럼프(150~200 mm)의 물성을 가지며 설계강도가 100 MPa 이상인 콘크리트 배합비를 개발하여 적용하고, 원심성형 각형보를 제작하기 위한 특수거푸집을 제작하여 원심성형 각형보를 생산하였다. 생산된 원심성형 각형보는 원심성형 부재의 표준 휨 및 전단 시험기준에 따라 성능시험을 수행하였다. 4개의 시험체에 대한 정적재하시험 결과는 설계기준에서 제시하고 있는 단면의 공칭휨강도, 공칭전단강도 이상으로 나타나 초고강도 원심성형 각형보의 구조적인 신뢰성이 입증되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• 한국물환경학회지
• /
• 제28권5호
• /
• pp.729-742
• /
• 2012

Recently, to using chemical coagulation process for T-P removal in STP effluent as tertiary treatment process is generalized in the country. The importance of analysis technique to save the treatment & maintenance cost during coagulation process is becoming more increased each day. Thus, it is necessary for the analysis technique during coagulation process to be presented well the characteristic of coagulation in field apply. There are a few analysis techniques such as Jar Test, zeta potential analysis and streaming current detecting techniques. But there are difficult to apply in field immediately due to long test time and difficult analysis techniques. And using PDA technique, it is reviewed applicability of the techniques as field index on pilot plant of P-CAP system The P-CAP system is composed of an in-line static mixer, a Flocculation Tank and the CAP reactor with 2 stage weir for effluent. Pre-test is performed to fix the mixing velocity in the Flocculation Tank using the PDA equipment and it fixed with 30RPM. Also, Jar Test is performed to select optimum dose of each coagulant for each T-P concentration level of influent. Result of continuous test on pilot plant of P-CAP system, the FSI in the Flocculation Tank is increased consistently by increasing each dosing concentration of coagulant such as LAS and PAC in the low level influent T-P concentration comparatively. It is considered that formed Al-hydroxide complexes for dosed coagulant are caused FSI variation. Furthermore, it seems that FSI value in the high level influent T-P concentration appeared lower than the opposite influent condition relatively because it is formed simultaneously Al-hydroxide complexes as solid type and Al-phosphorus complexes as soluble type. Thus, relation of FSI by PDA technique and T-P removal of final effluent on pilot plant of P-CAP system are very limited for the kind of coagulant and the characteristics of influent. And it though that FSI value by PDA technique with analyzing of turbidity in Flocculation Tank will be used restrictedly on field as the relative field-index.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권4호
• /
• pp.368-377
• /
• 2013

대형디젤기관 배기가스 저감용 Urea-SCR 시스템은 높은 NOx 저감율을 보이는 반면, 높은 관통도를 갖는 요소수가 벽면 충돌 후 증발하지 못하고 벽면에 머물게 되어 우레아염을 형성한다. 우레아염 생성 방지를 위한 방안으로 벽면유동 형성을 촉진하기위한 믹서-하우징 조립체의 형상 최적화와 관련된 실험적 연구가 수행되었다. 하우징 경사각 변화 및 믹서 설치위치에 따라 벽면유동의 증가 가능성이 hot-wire 시스템을 이용하여 조사되었다. 벽면 유동은 하우징 경사각 및 믹서 설치 위치에 큰 영향을 받으며, 하우징 경사각이 있고 믹서가 하우징 후단에 설치될 때 벽면유동이 향상되는 것을 알 수 있었다.