외부 후 긴장 공법은 설계에 수반되는 구조해석이 비교적 명확하여 강교량 구조물뿐만 아니라 건축구조물 등 그 적용 범위가 매우 넓은 보강방법이다. 본 연구에서는 후 긴장 공법에 있어서 긴장력 도입 과정의 강합성보의 거동을 연구하기 위하여 긴장력 증가에 따른 긴장재, 경간 중앙부 하부 플랜지, 정착단 주형 하부 플랜지의 도입 변형율과 긴장재 절곡 각도에 따른 도입 전단력 및 압축력을 실험 및 해석적으로 분석하였다. 또한 긴장력 도입 후 정적 휨 재하 실험을 수행하여 긴장력 도입 정도에 따른 휨 보강 정도를 분석하였으며, 절곡 각도의 변화에 따른 전단보강 및 휨 보강 양상을 연구하였다. 그 결과 외부 후 긴장력 도입에 따른 휨 보강 효과가 매우 높은 것으로 분석되었으며, 긴장재의 절곡 배치에 의해서는 추가적으로 전단보강 효과까지 나타났다.
현장타설말뚝기초가 보다 빈번하게 여러가지 구조물의 기초로 쓰이고 있다. 그러나, 경사하중하의 현장타설말뚝의 거동에 대하여는 알려진 사실이 거의 없다. 본 연구에서는, 경사하중을 받는 현장타설말뚝의 비배수거동에 대하여 연구하고자 체계적인 실험을 행하였다. 기초의 직경에 대한 깊이의 비와 하중의 경사도가 같은 변수들을 변화시키면서 행한 연구를 통하여 경사하중에 대한 지지력을 예측하는 반이론적 방법을 개발하였다. 시험변수들은 실제 송전탑건설시 가장 빈번하게 사용되는 대표적인 값들과 같도록 선택되었다. 직경에 대한 말뚝의 깊이비(D/B)가 서로 다른 짧은 강체말뚝에 대하여 논하였으며, 축방향 인발, 경사 인발, 그리고 경사 압축등과 같은 하중상태에 대하여 연구하였다. 경사지지력을 구조상호작용 방정식과 본 실험연구에서 개발한 공식을 사용하여 평가하여 보았다. 본 연구에서 개발한 새로운 공식은 실험실 시험치와, 제한적이나마, 현장의 실제시험치에 적용될 수 있음을 알 수 있었다.
2거더 철도교량의 사용성, 특히 부모멘트 영역의 휨강성을 증대시키기 위해서 이중합성단면이 제안되었다. 이 논문에서는 제안된 이중합성구조를 갖는 5m-5m의 연속 2거더 교량 모델에 대한 실험적 연구를 수행하였다. 교량 모델에 대한 실험적 연구를 통해서 유효폭,전단연결부, 이중합성단면의 극한강도에 대한 설계 고려사항을 연구하였다. 하부 콘크리트 바다판의 전단열결부는 완전합성 거동을 나타내어 제안된 경험식의 타당성을 검증하였다. 이중합성단면의 휨거동을 통해서 하부 콘크리트 슬래브의 유효폭은 압축을 받는 콘크리트 슬래브의 유효폭으로 계산될 수 있다. 교량모델의 극한 휨 강도 평가에서 이중합성단면의 완전소성해석이 타당함을 밝혔다. 실험결 과에 근거한 설계사항들이 제안되었다.
동영상에서의 관심 객체를 추출하는 것은 비디오 내용 분석과 비디오 검색 및 압축의 성능을 개선시키는데 큰 역할을 한다. 관심 객체는 단순히 사람 눈의 시선을 끄는 대상물이 아니라 내용전개의 중심이 되거나 제작자가 표현하려고 하는 핵심 객체를 의미한다. 이러한 관심 객체는 움직이는 객체뿐만 아니라 정지해 있는 객체도 될 수 있으나, 사람의 관심을 절차적으로 표현하는 것이 어렵기 때문에 관심 객체를 명확하게 정의하기가 곤란하다. 이에, 본 논문에서는 동영상 샷에서의 움직이는 객체의 위치, 크기, 움직임 패턴의 변화에 대한 조건을 정의하여 필터링에 의해 사람의 관심을 끄는 움직임 관심 객체를 추출하는 방법을 제시하고, 아울러 동영상 샷에서 정지되어 있는 객체에 대해서도 컬러/텍스처 특이성, 위치, 크기, 출현 빈도 등에 대한 조건을 정의하여 정지 관심 객체도 추출할 수 있는 방법을 제안한다. 제안한 방법을 50개의 동영상 샷에 대하여 실험한 결과, 사람이 선정한 움직임 및 정지 관심 객체를 84% 정도 추출할 수 있음을 확인할 수 있었다.
구속응력(拘束應力), 전단변형율진폭(剪斷變形率振幅), 다짐함수비(含水比), 다짐에너지, 간극비(間隙比) 및 포화도(飽和度)가 다짐점성토(粘性土)의 동적전단탄성계수(動的剪斷彈性係數)에 끼치는 영향(影響)을 연구(硏究)하기 위하여 도주공진시험(圖柱工振試驗)을 하였다. 이들 각각(各各)의 요소(要素)들은 다짐 흙의 동적전단탄성계수(動的剪斷彈性係數)에 큰 영향(影響)을 나타내며 그 원인(原因)은 다짐에 의한 흙의 여러 가지 변화(變化)로서 설명(說明)할 수 있다. 흙의 동적전단탄성계수(動的剪斷彈性係數)는 다짐에 의해서 크게 증가(增加)되며 최적함수비(最適含水比) 건조측(乾燥側)의 함수비(含水比)에서 다지는 것이 훨씬 더 효과적(効果的)이다. 그리고 동적(動的) 전단탄성계수(剪斷彈性係數)와 정적(靜的) 전단탄성도(剪斷彈性度)는 좋은 상관관계(相關關係)를 나타내며 이를 이용(利用)하여 어떤 일정(一定)한 구속응력(拘束應力)에 대한 동적전단탄성계수(動的剪斷彈性係數)를 일축압축강도(一軸壓縮强度)로부터 쉽게 구할 수가 있다.
In the present study, a unified viscoplastic-damage model has been applied in order to describe the mechanical characteristics of fresh water ice such as nonlinear material behavior and volume fraction. The strain softening phenomenon of fresh water ice under quasi-static compressive loading has been evaluated based on unified viscoplastic model. The material degradation such as growth of slip/fraction has quite close relation with material inside damage. The volume fraction phenomenon of fresh water ice has been identified based on volume fraction (nucleation and growth of damage) model. The viscoplastic-damage model has been transformed to the fully implicit formulation and the discretized formulation has been implemented to ABAQUS user defined subroutine (User MATerial: UMAT) for the benefit of application of commercial finite element program. The proposed computational analysis method has been compared to uni-axial compression test of fresh water ice in order to validate the compatibilities, clarities and usefulness.
The results of an experimental and analytical study of composite pressure hull on buckling pressure are presented for LRN 300. Composite tensile test was done to know the composite material properties applied FE analysis for URN composite. We predicted the buckling and post buckling analysis of composite laminated cylindrical panels under external compression by using ABAQUS /Standard[Ver 6.4]. To obtain nonlinear static equilibrium solutions for unstable problems, where the load-displacement response can exhibit the type of nonlinear buckling behavior, during periods of the response, the load and/or the displacement may decrease as the solution evolves, used the modified Riks method. The modified Riks method is an algorithm that allows effective solution of such cases [7]. Experiments were conducted to verify the validation of present analysis for cross-ply laminated shells. The shells considered in the study have two different lamination patterns, $[{\pm}45/0/90]_{18s\;and}\;[/0/90]_{18s}$. Cylindrical panel of experiment and analysis have the radius of 200mm, length of 210mm and 60 degree of cutting angle. The critical load from experiment is $69\%$ of that of numerical analysis, because the fracture of matrix was generated before buckling. So URN 300 is not proper to use at the condition under high external pressue.
Murthy, A. Rama Chandra;Ganapathi, S. Chitra;Iyer, Nagesh R.;Lakshmanan, N.;Bhagavan, N.G.
Computers and Concrete
/
제10권1호
/
pp.1-18
/
2012
This paper presents the details of studies conducted on hollow concrete block masonry (HCBM) units and wall panels. This study includes, compressive strength of unit block, ungrouted and grouted HCB prisms, flexural strength evaluation, testing of HCBM panels with and without opening. Non-linear finite element (FE) analysis of HCBM panels with and without opening has been carried out by simulating the actual test conditions. Constant vertical load is applied on the top of the wall panel and then lateral load is applied in incremental manner. The in-plane deformation is recorded under each incremental lateral load. Displacement ductility factors and response reduction factors have been evaluated based on experimental results. From the study, it is observed that fully grouted and partially reinforced HCBM panel without opening performed well compared to other types of wall panels in lateral load resistance and displacement ductility. In all the wall panels, shear cracks originated at loading point and moved towards the compression toe of the wall. The force reduction factor of a wall panel with opening is much less when compared with fully reinforced wall panel with no opening. The displacement values obtained by non-linear FE analysis are found to be in good agreement with the corresponding experimental values. The influence of mortar joint has been included in the stress-strain behaviour as a monolith with HCBM and not considered separately. The derived response reduction factors will be useful for the design of reinforced HCBM wall panels subjected to lateral forces generated due to earthquakes.
In this study, unidirectional and plain woven carbon fiber reinforced magnesium matrix composite laminates were fabricated by the liquid pressing infiltration process, and evolutions of the microstructure and compressive strength of the composite laminates under corrosion were investigated by static immersion tests. In the case of the unidirectional composite laminate, the main microstructural damage during immersion appeared as a form of corrosion induced cracks, which were formed at both CF/Mg interfaces and the interfaces between layers. On the otherhand, wrap/fill interface cracks were mainly formed in the plain woven composite laminate, without any cracks at the CF/Mg interface. The formation of these cracks was considered to be associated with internal thermal residual stress, which was generated during cooling after the fabrication process of these materials. As a consequence of the corrosion induced cracks, the thickness of both laminates increased in directions vertical to the fibers with increasing immersion time. With increasing immersion time, the compressive strengths of both composite laminates also decreased continuously. It was found that the plain woven composite laminates have superior corrosion resistance and stability under a corrosive condition than unidirectional laminates.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.