This paper experimentally investigates the effects of oxygen-enriched air (OEA) on the running behaviors of an LPG SI engine during both start/warm-up (SW) and hot idling (HI) stages. The experiments were performed on an air-cooled, single-cylinder, 4-stroke, LPG SI engine with an electronic fuel injection system and an electrically-heated oxygen sensor. OEA containing 23% and 25% oxygen (by volume) was supplied for the experiments. The throttle position was fixed at that of idle condition. A fueling strategy was used as following: the fuel injection pulse width (FIPW) in the first cycle of injection was set 5.05 ms, and 2.6 ms in the subsequent cycles till the achieving of closed-loop control. In closed-loop mode, the FIPW was adjusted by the ECU in terms of the oxygen sensor feedback. Instantaneous engine speed, cylinder pressure, engine-out time-resolved HC, CO and NOx emissions and excess air coefficient (EAC) were measured and compared to the intake air baseline (ambient air, 21% oxygen). The results show that during SW stage, with the increase in the oxygen concentration in the intake air, the EAC of the mixture is much closer to the stoichiometric one and more oxygen is made available for oxidation, which results in evidently-improved combustion. The ignition in the first firing cycle starts earlier and peak pressure and maximum heat release rate both notably increase. The maximum engine speed is elevated and HC and CO emissions are reduced considerably. The percent reductions in HC emissions are about 48% and 68% in CO emissions about 52% and 78%; with 23% and 25% OEA, respectively, compared to ambient air. During HI stage, with OEA, the fuel amount per cycle increases due to closed-loop control, the engine speed rises, and speed stability is improved. The HC emissions notably decrease: about 60% and 80% with 23% and 25% OEA, respectively, compared to ambient air. The CO emissions remain at the same low level as with ambient air. During both SW and HI stages, intake air oxygen enrichment causes the delay of spark timing and the increased NOx emissions.
This paper is an attempt to give a concise overview of the state-of-the-art in the recent liquid hydrogen safety researches with unwanted event progress. The vessel of liquified hydrogen may fail and liquid hydrogen spilled. The hydrogen will immediately start to evaporate above a pool and make a hydrogen cloud. The cloud will disperse and can produce a vapor cloud explosion. The vessel containing the liquid hydrogen may not be able to cope with the boil-off due to heat influx, especially in case of a fire, and a BLEVE may occur. In equipment where it exists as compressed gas, a leak generates a jet of gas that can self-ignite immediately or after a short delay and produce a jet flame, or in case it ignites at a source a certain distance from the leak (delayed ignition), a flash fire occurs in the open and with confinement a deflagration or even detonation may develop. The up-to-date knowledge in these events, recent progress and future research are discussed in brief.
After heated discussion, National Police Agency decided not to install Red Arrow signal at such major intersections as Gwanghwamoon, Sejongro. The major issues can be summarized in the following reasons. The one is the conflict of color and symbol (red means STOP and arrow means PROGRESS), and it would confuse drivers and may cause traffic accident. The other includes high replacement cost. This paper delivered how much red arrow signal would affect (1) drivers start up delay time, (2) saturation flow rate and (3) vehicle headway. The result showed that there was no statistical difference in those even when a red arrow signal is placed.
Kim, Dong-Ho;Kim, Byung-Chul;Cho, You-Ze;Kwon, Yul
Journal of KIISE:Information Networking
/
v.27
no.1
/
pp.98-107
/
2000
This paper compares the performance of feedback consolidation algorithms with or without a fast overload indication function which has been recently proposed in the ATM Forum for multicast ABR (Available Bit Rate) services in ATM networks. We use the performance criteria such as the ACR (Allowed Cell Rate) of a source, queue length at a switch, link utilization, fairness, and BRM (Backward Resource Management) cell overhead. Simulation results show that performance of the feedback consolidation algorithms with a fast overload indication function can be improved sign.ificantly than that of algorithms without this function in terms of ramp-down delay, particularly in initial start-up period or under a severe overload situation. The fast overload indication function can be combined with any feedback consolidation algorithm, whereas its performance is highly dependent on an underlying basic feedback consolidation algorithm.
Fair packet scheduling algorithms supporting quality-of-services of real-time multimedia applications can be classified into the following two design schemes in terms of the reference time used in calculating the timestamp of arriving packet: Finish-time Design (FD) and Start-time Design (SD) schemes. Since the former can adjust the latency of a flow with raising the flow's reserved rate, it has been applied to a router for the guaranteed service of the IETF (Internet Engineering Task Force) IntServ model. However, the FD scheme may incur severe bandwidth loss for traffic flows requiring low-rate but strong delay bound such as internet phone. In order to verify the usefulness of the SD scheme based router for the IETF guaranteed service, this paper analyzes and compares two design schemes in terms of bandwidth and payload utilizations. It is analytically proved that the SD scheme is better bandwidth utilization than the FD one, and the simulation result shows that the SD scheme gives better payload utilization by up to 20%.
Masoud, Mohammad;Jaradat, Yousef;Jannoud, Ismael;Huang, Hong
KSII Transactions on Internet and Information Systems (TIIS)
/
v.11
no.7
/
pp.3351-3369
/
2017
In recent years, datacenters, network devices and computers have proliferated. The power consumed by information and communication technology (ICT) devices has inflated in an extraordinary manner. Green communication has emerged as a new approach to reduce and optimize power consumption in ICT sector. Many methods and protocols have been proposed and implemented to achieve green communication. Nevertheless, the increase of power consumption remains a problem. In this work, we attempt to reduce and optimize power consumption of network devices in datacenters environment utilizing software defined network (SDN) paradigm. To gain more insight of the power consumption requirements of network switches, a power measurement system is constructed to measure power consumption levels of network devices. Subsequently, we propose a duplication resolver algorithm (DRA) to power off/on switches reactively. DRA algorithm reduces the required time by switches to construct their flow tables after rebooting. To this end, DRA-based external circuit has been constructed utilizing Ethernet module and an Arduino kit to control power supplies of network devices. To facilitate our work, a testbed has been constructed utilizing Ryu SDN controller, HP2920-24G switches and Arduino kits. Our results show that DRA algorithm can reduce both the power usage and start-up time delay of network switches after failures.
RMCP is an application layer multicast protocol and was established as a standard by ITU-T Also, RMCP includes a scheme which can statically construct a multicast tree. In this paper, we propose a QoS based tree construction scheme which can dynamically construct a multicast tree. And this scheme shows more superior performance than the static tree scheme of RMCP in terms of start-up delay and user requirement QoS. This scheme consists of a best-fit method using multiple sub-net groups which are satisfied a user requirement QoS and a first-fit method using one sub-net group which has maximum transmission bandwidth. In simulation result, two proposed methods are superior to the existing static tree scheme.
This paper proposes a universal system control strategy for voltage source converter (VSC) based high voltage direct current (HVDC) systems. The framework of the designed control strategy consists of five layer structures considering the topology and control characteristics of the VSC-HVDC system. The control commands sent from the topmost layer can be transmitted to the next layer based on the existing communication system. When the commands are sent to each substation, the following transmission of commands between the four lower layers are realized using the internal communication system while ignoring the communication delay. This hierarchical control strategy can be easily applied to any VSC-HVDC system with any topology. Furthermore, an integrated controller for each converter is designed and implemented considering all of the possible operating states. The modular-designed integrated controller makes it quite easy to extend its operating states if necessary, and it is available for any kind of VSC. A detailed model of a VSC-HVDC system containing a DC hub is built in the PSCAD/EMTDC environment. Simulation results based on three operating conditions (the start-up process, the voltage margin control method and the master-slave control method) demonstrate the flexibility and validity of the proposed control strategy.
Geoffroy, Pierre Alexis;El Abbassi, El Mountacer Billah;Maruani, Julia;Etain, Bruno;Lejoyeux, Michel;Amad, Ali;Courtet, Philippe;Dubertret, Caroline;Gorwood, Philip;Vaiva, Guillaume;Bellivier, Frank;Chevret, Sylvie
Psychiatry investigation
/
v.15
no.12
/
pp.1188-1202
/
2018
Objective This study protocol aims to determine, using a rigorous approach in patients with bipolar disorder (BD) and non-seasonal major depressive episode (MDE), the characteristics of bright light therapy (BLT) administration (duration, escalation, morning and mid-day exposures) depending on the tolerance (hypomanic symptoms). Methods Patients with BD I or II and treated by a mood stabilizer are eligible. After 1 week of placebo, patients are randomized between either morning or mid-day exposure for 10 weeks of active BLT with glasses using a dose escalation at 7.5, 10, 15, 30 and 45 minutes/day. A further follow-up visit is planned 6 months after inclusion. Patients will be included by cohorts of 3, with at least 3 days of delay between them, and 1 week between cohorts. If none meet a dose limiting toxicity (DLT; i.e hypomanic symptoms), the initiation dose of the next cohort will be increased. If one patient meet a DLT, an additionnal cohort will start at the same dose. If 2 or 3 patients meet a DLT, from the same cohort or from two cohorts at the same dose initiation, the maximum tolerated dose is defined. This dose escalation will also take into account DLTs observed during the intra-subject escalation on previous cohorts, with a "Target Ceiling Dose" defined if 2 DLTs occured at a dose. Discussion Using an innovative and more ergonomic device in the form of glasses, this study aims to better codify the use of BLT in BD to ensure a good initiation and tolerance.
Cleft lip and palate is one of the congenital anomalies which need comprehensive and multidisciplinary treatment plan because 1) oral cavity is an important organ with masticatory function as a start of digestive tract, 2) anatomic symmetry and balance is esthetically important in midfacial area, and 3) it is also important to prevent psycho-social problems by adequate restoration of normal facial appearance. There are many different protocols in the treatment of cleft lip and palate, but our department has adopted and modified the $Z{\"{u}}rich$ protocol, as published in the Journal of Korean Cleft Lip and Palate Association in 1998. The first challenge is feeding. Type of feeding aid ranges from simple obturators to active orthopedic appliances. In our department we use passive-type plate made up of soft and hard acrylic resin which permits normal maxillary growth. We use Millard's method to restore normal appearance and function of unilateral complete cleft lip. In consideration of both maxillary growth and phonetic problems, we first close soft palate at 18 months of age and delay the hard palate palatoplasty until 4 to 5 years of age. When soft palate is closed, posterior third of the hard palate is intentionally not denuded to allow normal maxillary growth. In hard palate palatoplasty the mucoperiosteum of affected site is not mobilized to permit residual growth of the maxilla. We have treated a patient with unilateral complete cleft lip and palate by Ajou protocol, which is a kind of modified $Z{\"{u}}rich$ protocol. It is as follows: Infantile orthopedics with passive-type plate such as Hotz plate, cheiloplasty with Millard's rotation-advancement flap, and two stage palatoplasty. It is followed by orthodontic treatment and secondary osteoplasty to augment cleft alveolus, orthognathic surgery, and finally rehabilitation with conventional prosthodontic treatment or implant installation. The result was good up to now, but we are later to investigate the final result with longitudinal follow-up study according to master plan by Ajou protocol.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.