• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.149-151
• /
• 2006

This paper shows the characteristic analysis of single-phase LSPM(Line Start Permanent Magnet) synchronous motor considering overhang structure. To obtain the dynamic and steady performance of the motor, the D-Q equivalent circuit is used and the circuit parameters are extracted by 3D FEM. The performance of the model with overhang is compared with conventional model without overhang on the condition that both models have the same volume of the permanent magnet.

• Journal of Power Electronics
• /
• 제5권3호
• /
• pp.240-246
• /
• 2005

Considering the start-up and economical efficiency, the optical sensor technique using a slotted-disk and an opto-interrupter are appropriate, however, this method needs three opto-interrupters and a slotted-disk when driving the 6/4 pole SRM(switched reluctance motor). In this paper, we propose an economic method by replacing the conventional opto-interrupter and slotted-disk with only optical sensor which enables the motor to start up and forward and reverse operation. Also the control circuit includes only analog devices, which makes the process more economical.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1030-1032
• /
• 2003

Single phase SRM(switched reluctance motor) can not be start by itself because positive torque is generated in limited section. Therefore single phase SRM need starting device which is place the rotor in positive torque section when motor is begun to start. The prototype of salient pole rotor type single phase SRM, fabricated in previous research, has permanent magnet starting device. It is installed in bottom of the rotor for starting by itself. But, it is affected the motor when driving and cause the decrease of torque and speed. On this paper, average torque of the prototype was measured according to installation of the starting device or not. And influence of the staring device on average torque was confirmed by comparison of the results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1117-1119
• /
• 2005

The inductance is an important parameter in order to analyze steady state of LSRM(Line-start Synchronous Reluctance Motor). If FEM(Finite Element Method) is used to compute the parameter according to the change of flux barriers and conductor bars, less analysis time is required. Therefore, this paper adopts equivalent magnetic circuit method to simply calculates inductance, and the result is verified by comparing with the results by FEM.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.90-97
• /
• 1991

본 연구에서는 하이브리드 스텝핑 모터의 공진 배제를 위한 폐회로제어시스템 을 개발하였고 펄스 발생, 위치 및 속도변화, 가감속제어, 정여괴전방향결정, 카운트 및 스텝핑 모터의 온/오프기능 등을 하드웨어 대신 마이크로컴퓨터를 이용한 소프트웨 어로 대치하였으며, 구동회로의 복잡함을 피하기 위해 스텝핑 모터의 전용제어기인 PMM8713IC를 사용하였고 궤환정보는 샤프트 엔코더를 사용하였다.그리고 리드 스크 루우를 사용한 1축 테이블을 제작하여 개회로제어시와 폐회로제어시의 동특성 및 공진 현상을 검토하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.126-128
• /
• 2007

The purpose of This paper is the optimal design of a single-phase LSPM(Line-Start Permanent magnet Motor). A single-phase LSPM has a permanent magnet in the rotor that is same as induction motor. For that reason, the transient characteristics are very different from an induction motor Therefore, we need the PM design to consider a transient and steady- state characteristics. In this paper, we designed a single-phase LSPM that has a high power and a good starting characteristics, and analyzed the performance of designed LSPM by varying each parameters. Finally, we examined and compared the simulation results and the prototype motor's characteristics.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.

• 전력전자학회논문지
• /
• 제5권5호
• /
• pp.427-434
• /
• 2000

본 논문은 유도전동기의 직접벡터 제어 시스템에서 전동기가 기동 시 토크 충격없이 부드럽게 기동할 수 있는 기동기법을 제시한다. 정지모드에서는 고정자 전류만으로 고정자자속을 계산하는 방식을 사용하며, 기동 후 직접 벡터제어 모드에서는 프로그램어블 3-단계 저역필터로 고정자자속을 계산한다. 정지모드에서 직접벡터제어 모드로 변환 시 3-단계 저역필터의 시간지연으로 고정자 자속이 급격히 감소되어 토크 역시 갑자기 감소된다. 본 논문에서는 전동기가 기동 시 토크 충격을 방지하기 위한 고정자 자속의 피이드포워드 제어 기법을 제시하고, 시뮬레이션 및 실험을 통하여 이 기법의 타당성을 확인한다.

• 전기학회논문지
• /
• 제65권1호
• /
• pp.58-64
• /
• 2016

In this paper, the design of rotor shape was performed for improvement of start-up characteristics and efficiency in single-phase LSPM. In order to improve the start-up characteristics, shape of rotor aluminium cage bar was changed. Through arrangement of permanent magnets and installation of flux barriers, it was performed torque ripple reduction and efficiency improvement. Cogging torque and back-EMF is calculated by the no-load analysis, start-up time is calculated by the start-up state analysis, efficiency and torque ripple is calculated by steady state analysis. The characteristics of the motor were calculated through FEM.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2017년도 춘계학술발표대회
• /
• pp.123-125
• /
• 2017

최근 에너지 시장에 많은 변화가 일어나면서 국내 에너지 수급 현황에도 큰 영향을 끼치고 있다[1-2]. 발전소의 블랙 다운시 Battery Panel에서 전원을 공급받아 DC MOTOR를 기동하여 중요한 시설에 전원을 공급한다. 따라서 본 논문에서는 PSIM 시뮬레이션을 이용하여 37kW급 DC MOTOR 기동제어를 시뮬레이션 하였다. 시뮬레이션 결과 초기 기동 전류는 정격전류 170A의 200% 이내에서 동작해야 하는 조건을 만족 시켰다.