• Journal of the Korean Institute of Navigation
• /
• v.17 no.3
• /
• pp.77-83
• /
• 1993

The goal of this research is to get a measuring system for absorption characteristics over the frequency band with 30MHz to 1, 000MHz concerning the ferrite electromagnetic wave absorbers, for example, grid-type and sintered flat type, etc. It is, however, very difficult to measure the absorption characteristics as in low frequency as in 30 MHz. In this research, therefore, we propose a standing wave method using parallel striplines, fabricate the measuring system, and measure the characteristic of ferrite microwave absorbers using the proposed mea-suring system.

• Journal of Navigation and Port Research
• /
• v.27 no.4
• /
• pp.455-463
• /
• 2003

Time series of suspended sediment concentration, surface elevation and velocity were measured and analysed to investigate the role of waves and the predominance of infra-gravity wave component for sediment suspension phenomena in the surf zone. For the investigation in detail, we adopted the cross spectral analysis method between suspended sediment concentration and the characteristic values of wave, and ensemble average analysis method about long-period wave component, which is dominant to sediment suspension in the measurement point. The obtained results are summarized as follows: 1)The relationship between suspended sediment concentration and the characteristic values of wave is stronger for the long-period standing wave components(about 60s and 30s where the nodal point of the first mode and the anti-nodal point of the second mode are located at the measurement point, respectively) than the long wave components(about 100s), which have the most energetic power, 2) and also, it is cleared that suspended sediment concentration is increased in the case of the phase, the velocity components of the first mode long-period standing wave(60sec) were accelerated toward on-shore direction, that is, the water surface in offshore side is higher than on-shore side.

• Journal of computational fluids engineering
• /
• v.12 no.1
• /
• pp.53-59
• /
• 2007

An axisymmetric supersonic screeching jet is numerically simulated to examine the length scales of screech frequency as well as screech tone generation mechanism. The axisymmetric Reynolds-averaged Navier-Stokes equations in conjuction with a modified Spalart-Allmaras turbulence model are employed. It is demonstrated that the axisymmetric jet screech tones can be simulated correctly and the numerical results are in good agreement with the experimental data. Instability waves, shock-cell structures and the phenomena of shock motion are investigated in detail to identify the screech tone generation mechanism. Shock spacings and standing wave length are analyzed to determine the dominent length scale crucial to the screech frequency formulation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.175-180
• /
• 2006

The acoustical properties of multi-layered treatments of materials used in applications, such as automotive liners, generally cannot be directly measured by a one-time test in a standing wave duct. Therefore, we have to consider predicting them by the four-pole transfer matrix method. This method requires performing TCM or TLM for measuring the transfer matrix of each layer and calculating the total transfer matrix of the whole multi-layered material. The final predicted absorption ratios and transmission losses of the multi-layered treatments strongly depend on the measured transfer matrix of each layer. All these functions have been included in a new designed acoustical software.

• Current Optics and Photonics
• /
• v.4 no.2
• /
• pp.141-147
• /
• 2020

To understand the cause of the high light transmittance of the human eye, the optical effects of the collagen fibers of the stroma layer, which constitute the majority of the cornea, were analyzed. These collagen fibers, approximately 20 nm in diameter, have a regular arrangement. Accordingly, the optical properties of the collagen fibers and the fiber layer were analyzed by simulation. A standing wave was formed in the incident space by the overlapping incident light and the light reflected by the plate. In addition, it was confirmed that when the collagen fibers are arranged in a layer, the light transmittance periodically changes, depending on the number of fiber layers. The standing wave was formed in the incident space, and the light's intensity distribution was changed by the nanoscale collagen fibers in the section with the collagen layer, which affected the transmittance. To explain this phenomenon, the collagen fiber was defined as a second light source, and an attempt was made to describe the simulation results in terms of overlap of the incident light with the light emitted from the collagen fiber.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.12
• /
• pp.573-577
• /
• 2002

We designed wideband HTS antennas which consists of two triangle -radiation patches using a $YBa_2Cu_3O_{7-X}$ (YBCO) superconducting thin film. The major limitation of high-Tc superconducting (HTS) microstrip antennas is the narrow bandwidth due to the high Q and thin substrate. Defining bandwidth as the frequency range over which standing wave ratio (SWR) 2:1 or less, HTS antenna bandwidths are typically 0.85 % to 1.1 %. Thus considerable effort has been focused on developing antennas for broadband operation. To calculate input impedance and design of the broadband HTS antennas a moment method technique was used. The HTS antenna fabricated in this work was designed for K-band, which is useful band for satellite to satellite communications. The bandwidth obtained was a significant 6.7 % and the other measured performance of our HTS antenna, including the bandwidth, radiation Pattern, efficiency, standing wave ratio (SWR) and return losses was reported.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.523-526
• /
• 2002

We designed wideband HTS antennas which consists of two triangle-radiation patches using a YBa$_2$Cu$_3$O$\sub$7-x/ (YBCO) superconducting thin film. The major limitation of high-Tc superconducting (HTS) microstrip antennas is the narrow bandwidth due to the high Q and thin substrate. Defining bandwidth as the frequency range over which standing wave ratio (SWR) 2:1 or less, HTS antenna bandwidths are typically 0.85% to 1.1%. Thus considerable effort has been focused on developing antennas for broadband operation. To calculate input impedance and design of the broadband HTS antennas a moment method technique was used. The HTS antenna fabricated in this work was designed for K-band, which is useful band for satellite-to-satellite communications. The bandwidth obtained was a significant 6.7% and the other measured performance of our HTS antenna, including the bandwidth, radiation Pattern, efficiency, standing wave ratio (SWR) and return losses was reported.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.647-650
• /
• 2002

A thermoacoustic refrigerator, using a resonant standing acoustic wave, has been built. It employs a loudspeaker to sustain a standing wave in a resonance tube. The stack of plates is 0.075mm-thick plastic sheet(Mylar), spirally wound to make a 40mm-diameter assembly 80mm long. and two heat exchanger are installed. The refrigerant is Helium gas. The description of thermoacoustic refrigerator are presented. The directly measured performance of the resonator. Tc/Th ( temperature ratio ) and $COP/COP_{c}$, (normalized by carnot's COP ) are plotted versus the thermal load Q applied to the cold end, for various speaker power.

• Journal of KSNVE
• /
• v.7 no.5
• /
• pp.797-801
• /
• 1997

This paper raises issues in testing the absorption coefficients of sound-absorptive samples using the standing wave apparatus according to the Korean standard of KS F 2814. The standard code does not consider any effect of air-damping which is significant in testing relatively low sound-absorptive samples. This limitation has been shown to yield much variation of sound absorption coefficients for recent samples tests whose coefficients are less than 10%. An improved method of calculating the sound absorption coefficients is proposed in this work and its effectiveness in real test is also illustrated. Finally, the guideline for the modification of our national standard code KS F 2814 is proposed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1198-1201
• /
• 2006

ISO 140-1 recommends installing diffusing elements in the room if there are large variations of the sound pressure level caused by strong standing wave. Also it requires that reverberation time should not be long or short. In accordance to this regulation, we adjusted the reverberation time in the range of $1{\sim}2$ sec by using 4 types of diffusing elements. This paper demonstrates how to balance the reverberation time in the range of $1{\sim}2$ sec by using several types of diffusing elements.