• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.2
• /
• pp.109-116
• /
• 2022

In this paper, we propose a band rejection filter (BRF) with a state variable filter (SVF) structure to effectively remove the influence of 60 Hz line frequency noise introduced into the sensor system. The conventional BRF of the SVF structure uses an additional operational amplifier (OPAMP) to add a low pass filter (LPF) output and a high pass filter (HPF) output or an input signal and a band pass filter. Therefore, the notch frequency and the notch depth that determine the signal attenuation of the BRF greatly depend on the tolerance of the resistors used to obtain the sum or difference of the signals. On the other hand, in the proposed BRF, since the BRF output is formed naturally within the SVF structure, there is no need for a combination between each port. The notch frequency of the proposed BRF is 59.99 Hz, and it can be confirmed that it is not affected at all by the tolerance of the resistor through the Monte Carlo simulation results. The notch depth also has an average of -42.54dB and a standard deviation of 0.63dB, confirming that normal operation as a BRF is possible. Also, with the proposed BRF, noise filtering was applied to the electrocardiogram (ECG) signal that interfered with 60 Hz noise, and it was confirmed that the 60 Hz noise was appropriately suppressed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.5
• /
• pp.185-189
• /
• 2005

This paper focuses on the design for Rx/Tx switch module of GSM(global standard mobile) band, characterization of a miniature, low power and dual-band implementation of the front-end switch module with low-pass filer And the effort to make agreement between the simulated design and the measured data for these solutions takes the place through accumulated design and manufacturing data library. We present the design, modeling and measurement of switch module integrating GSM Rx/Tx switching circuit and LPF(low pass filter) on a LTCC(low temperature co-fired ceramic) substrate. For GSM application, insertion and return loss of the low pass filter designed was less than 0.3 dB which was less than 12.7 dB at 900 MHz. The LTCC switch module contained 10 embedded passives and 3 surface mount components integrated on 4.6$\times$4.8$\times$1.2 mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module measured at 900 MHz was 11 dB. In both of the design approach yielded excellent agreement between measured and simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.904-911
• /
• 2011

This paper deals with transmission characteristics of a new dual resonant structure for designing waveguide band-pass filter. The structure which has a pass-band between two adjacent stop-bands in a single body consists of circular ridged aperture and four armed conducting patch. The dual resonant behavior of the structure can be represented by a combination of LC series and parallel resonant circuits. Also these resonant properties can be easily controlled by varying the geometry of the aperture and four armed conducting patch. Actually, the structure is fabricated on the microstrip substrate by use of etching technique so that it is formed an iris type resonator which can be easily put into the transverse plane of the waveguide. We use WR-90 standard waveguide, adapters, and VNA(vector network analyzer) to measure the resonant characteristics of the structure. It is very useful to design and to improve the cutoff skirts characteristics in the waveguide band-pass filter design area.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.3
• /
• pp.63-71
• /
• 2000

A new type of second-order digital peaking filters for professional-quality digital audio system is proposed whose frequency response can be elaborately controlled throughout the composite structure of a standard band-pass filter and a 0-dB bypass gain. The proposed method for designing the peaking filter uses the Q-compensation technique to prevent the Q-distortion caused by the variation of the gain factor and is reduced into a compact form which is proper to the real-time implementation. Methods are examined for computing its coefficients, which are exact and very straightforward to compute with small amount of the system resources.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.130-133
• /
• 2005

This paper presents the efficient method to detect the defective detectors of the SWIR band of SPOT 4. The key of this method are to flatten the baseline of the data using high pass band filter instead of differentiation. This method is made up six steps. First step is to apply image enhancement techniques to enhance the lines imaged by defective detector and improve the quality of an image. Second step is processed by summing the enhanced image in line direction. These summed data have the peaks that represent the defective detectors and the curved baseline characterized by the reflectivity of Earth surface. In order to exactly detect these peaks, third step is to flatten the curved baseline using high pass filtering in the frequency domain. In fourth step, the data with flat baseline is normalized to have zero mean and unity standard deviation. In fifth step, the defective detectors are detected using $99.9\%$ confidence interval. Finally, after removing the detected ones in summed data, the steps from third to five are iterated. Three SPOT 4 images, which have different reflectivity of Earth surface and different sensor, were used to validate this method. The overall accuracy of detection for three images was $97.9\%$. This result shows that this method can detect efficiently the lines made by defective detectors.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.57-63
• /
• 2011

This paper presents a tunable band pass filter (BPF) for multi bio-signal detection. The bandwidth can be controlled by the bias current of transconductance (gm), while conventional BPF exploited switchable capacitor array for band selection. With this design technique, the die area of proposed BPF reduced to at least one tenth the area of conventional design. The simulation results show the high cut-off frequency tuning range of from 100Hz to 1Khz. The circuit was implemented with a 0.18um CMOS standard technology. Total current consumption is 1uA at the supply voltage of 1V with sub-threshold design technique.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.1
• /
• pp.58.1-58.1
• /
• 2017

National Youth Space Center has recently founded the Deokheung Optical Astronomy Observatory (DOAO) 1m Telescope, which accepts community observing applications since 2016. Standardization and calibration of the new observing facility are essential for astronomical research. In this poster, we present standardization processes and preliminary results for photometry of the Johnson-Cousins BVRI filter system. We selected sample data from a night in stable weather condition. After bias, dark, and flat corrections and photometry using ccdred and daophot package of IRAF, we derived standardized band pass parameters including color terms. The corrected photometry results of the BVRI filter system show reduced deviations from the standard magnitudes in the literature. In addition, we calculated atmospheric extinction coefficients and limiting magnitudes of the telescope system. We plan to extend these standardizing processes to flux calibration of narrow band filters, e.g. $H{\alpha}$ filter.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.89.1-89.1
• /
• 2017

In this poster, we present standard calibration processes and results for photometry of $H-{\alpha}$ filter using broadband filters. We took data from a night in stable weather condition. And we derived parameters for band pass calibration including color terms. The corrected photometry results from broadband filters like V and R filters showed high correlation enough to replace instrumental $H-{\alpha}$ magnitude. We plan to extend these standardizing processes to another narrowband filters and flux calibration of narrowband filters from photometry of PNe.

• Journal of KIISE:Software and Applications
• /
• v.34 no.3
• /
• pp.226-234
• /
• 2007

In this paper, we develop a speech recognition system using a throat microphone. The use of this kind of microphone minimizes the impact of environmental noise. However, because of the absence of high frequencies and the partially loss of formant frequencies, previous systems developed with those devices have shown a lower recognition rate than systems which use standard microphone signals. This problem has led to researchers using throat microphone signals as supplementary data sources supporting standard microphone signals. In this paper, we present a high performance ASR system which we developed using only a throat microphone by taking advantage of Korean Phonological Feature Theory and a detailed throat signal analysis. Analyzing the spectrum and the result of FFT of the throat microphone signal, we find that the conventional MFCC feature vector that uses a critical pass filter does not characterize the throat microphone signals well. We also describe the conditions of the feature extraction algorithm which make it best suited for throat microphone signal analysis. The conditions involve (1) a sensitive band-pass filter and (2) use of feature vector which is suitable for voice/non-voice classification. We experimentally show that the ZCPA algorithm designed to meet these conditions improves the recognizer's performance by approximately 16%. And we find that an additional noise-canceling algorithm such as RAST A results in 2% more performance improvement.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.1
• /
• pp.49-55
• /
• 2003

The use of digital filters in the signal process field is increasing rapidly with development of the modern industrial society. Especially, detail processors, Y/C separators, ghost removing filters, standard converters (NTSC to PAL or PAL to NTSC) and noise reducers, all of which use digital filters, tend to be used in digital video and audio processing, CATV and various communication fields. Generally, there are two different digital filters, the Rf (infinite impulse response) filter and the FIR (finite impulse response) filter in digital filter. In this paper, we have designed FIR filter which has the phase linearity and the easiness of creation. In the design of the FIR digital filter, the window function is used to alleviate the ripples caused by Gibbs Phenomenon around the cut off frequency of the band pass. But there're some problems to choose proper window function for the design destination due to its fixed values. Therefore, in this paper, we designed a modified Hanning window with new parameter which is adaptively chosen corresponding to design objectives. The digital filter was simulated to prove the validity of the model and it was compared with the Hamming, the Manning, the Blacknan and the Kaiser window function. And we have used peak side-lobe and transient characteristics as standard of judgement.