• Journal of Sensor Science and Technology
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2005

For more convenient electrode-electrolyte interface impedance analysis in biosensor, a stand-alone impedance measurement system is required. In our study, we developed a PC-based portable system to analyze impedance of the electrochemical cell using microprocessor. The devised system consists of signal generator, programmable amplifiers, A/D converter, low pass filter, potentiostat, I/V converter, microprocessor, and PC interface. As a microprocessor, PIC16F877 which has the processing speed of 5 MIPS was used. For data acquisition, the sampling rate at 40 k samples/sec, resolution of 12 bit is used. RS-232 with 115.2 kbps speed is used for the PC communication. The square wave was used as stimuli signal for impedance analysis and voltage-controlled current measurement method of three-electrode-method were adopted. Acquired voltage and current data are calculated to multifrequency impedance signal after Fourier transform. To evaluate the implemented system, we set up the dummy cell as equivalent circuit of which was composed of resistor, parallel circuit of capacitor and resistor connected in parallel and measured the impedance of the dummy cell; the result showed that there exist accuracy within 5 % errors and reproduction within 1 % errors compared to output of Hioki LCR tester and HP impedance analyzer as a standard product. These results imply that it is possible to analyze electrode-electrolyte interface impedance quantitatively in biosensor and to implement the more portable high speed impedance analysis system compared to existing systems.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.990-995
• /
• 1999

To determine the effect of chemical structure of linear amine curing agents on thermal and mechanical properties, standard epoxy resin DGEBA was cured with ethylene diamine(EDA) and hexamethylene diamine(HMDA) in a stoichiometrically equivalent ratio. From this work, the effect of linear amine curing agents on the thermal and mechanical properties is significantly influenced by the chemical structure or chain length of curing agents. In contrast, the results show that the DGEBA/EDA system having the two carbons had higher values in the thermal stability, maximum conversion of epoxide, density, glass transition temperature, tensile modulus, flexural strength, and flexural modulus than the DGEBA/HMDA system having the six carbons, whereas the DGEBA/EDA cure system had relatively low values in the shrinkage(%), thermal expansion coefficient, tensile strength, and had similar values in the maximum exothermic temperature, and conversion of epoxide compared to the DGEBA/HMDA cure system. This findings indicate that packing ability in the HMDA structure affects the thermal and mechanical properties.

• Nuclear Engineering and Technology
• /
• v.27 no.5
• /
• pp.645-660
• /
• 1995

The loss of Residual Heat Removal System (RHRS) event during reduced inventory operation for the Korean Standard Nuclear Power Plants (KSNPPS) is simulated by RELAP5/MOD3 and RELAP5/MOD3.1 Tn cases are considered : Base case for an intact Reactor Coolant System (RCS) with no tent and a vent case for an open system. Comparative simulations of base case are peformed by RELAP5/MOD3 and RELAP5/MOD3. 1 computer codes. The results of too simulations are generally in good qualitative and quantitative agreement. However, since the results of RELAP5/MOD3 simulation reveals the deficiency of RELAP5/MOD3 wall heat model, the RELAP5/AOD3.1 computer code is used for the simulation of the vent case. The analysis result of base case show that two steam generators are insufficient to remove decay heat at one day after shutdown, where the RCS is closed. The RCS pressure increased continuously and reached the RCS temporary boundaries design pressure of 0.24 MPa around 4,000 seconds. In the vent case with a flow capacity equivalent to three times the capacity of Pressurizer Safety Valve (PSV), it is shown that the RCS Pressure does not reach 0.24 MPa and core uncovery does not occur until 10,000 seconds. The detailed discussions on the results of this study suggest the feasibility of RELAP5/AOD3.1 as an analysis tool for the simulation of the loss of RHRS event at reduced inventory operation. The results of this study also provide insight for the determination of proper vent capacity.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.1
• /
• pp.19-26
• /
• 2019

The masonry infill walls are one of the most popular components that are used for dividing and arranging spaces in building construction. In spite of the fact that the masonry infills have many advantages, the system needs to be used with caution when the earthquake load is to be considered. The infills tend to develop diagonal compression struts during earthquake and increase the demand in surrounding RC frames. If there are openings in the infill walls, the loading path gets even complicated and the engineering judgements are required for designing the system. In this study, a masonry infill system was investigated through finite element analysis (FEA) and the results were compared with the current design standard, ASCE 41. It is noted that the equivalent width of the compression strut estimated by ASCE 41 could be 32% less than that using detailed FEA. The global load resisting capacity was also estimated by 28% less when ASCE 41 was used compare to the FEA case. Rather than using expensive FEA, the adapting ASCE 41 for the analysis and design of the masonry infills with openings would provide a good estimation by about 25% conservatively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.163-172
• /
• 2011

The CFTA girder developed is a concrete filled steel tubular system with arched shape and external post-tensioning (PT) tendons which control the initial camber and the bending stress of the girder. In the present study the effects of the PT tendons on the dynamic behavior of the girder subjected to a moving vehicle load are numerically investigated. Various levels for the tendon quantity and the tendon forces are considered, using the existing FE model of the girder. The vehicle considered is a DB-24 truck and is modeled with two tracks-three axles. Equivalent-load pulse time histories are applied to each node to simulate the moving vehicle, depending on the time of arrival and the discretization. The vehicle speeds are varied from 40 km/hr to 100 km/hr with increment of 20 km/hr. The analysis results show that the tendon forces do not produce any influences on the dynamic responses of the girder. However the dymamic deflection of the girder increases when a smaller amount of tendons is used. The Dynamic Amplification Factors (DAF) are evaluated based on the static and dynamic responses. Much lower values of the DAF are obtained, even no tendons applied, than those provided by the design criteria of the AASHTO LRFD and the Korea Highway Standard Specification.

• Land and Housing Review
• /
• v.2 no.1
• /
• pp.69-78
• /
• 2011

The purpose of this research is particle shape evaluation of aggregate using Digital Image Process(DIP). DIP is very useful to measure the roughness and particle shape of aggregates. Couple of aggregates, like standard sand, two different crushed stones, and two different marine aggregates, have been employed. Shape factors of two different marine aggregates are ranged 0.35 to 0.54. Crushed stone I is 0.74 which is highly flat, but standard sand is elongated shape. Especially, two marine aggregate showed a big difference of width and length which meaned a long shape. There is any significant difference of elongation ratio and flatness for each aggregate with different measuring system, like direct measurement of vernier calipers and DIP method. Shape conversion coefficient and equivalent diameter for changing 2D image to 3D image by the Digital Image Process(DIP) have been suggested and modified particle size distribution curve has been showed. The measured flatness ratios of each aggregate were 0.30, 0.36, 0.47 and 0.83, respectively. Also, the conversion shape coefficients of each aggregate were determinded as 0.77, 0.78, 0.84 and 0.92. The size of aggregate has been modified by multiplying the shape conversion coefficient and the aggregate size from DIP. The modified gradation curve with modified volume and weight of aggregate has been suggested. Within the limited test results, DIP is one of useful to get the particle shape of aggregate with limitation of measuring errors and to apply the particle distribution curve.

• Journal of Engineering Education Research
• /
• v.21 no.4
• /
• pp.53-62
• /
• 2018

The purpose of this study is to investigate the current conditions of the domestic and foreign curricula in the field of chemical engineering and to draw implications. The results of the study are as follows. Most of the domestic research universities (including non-certified universities) have curricula organized within the scope of the ABEEK certification, which is the minimum standard guide for chemical engineering curricula. However, we are concerned that chemical engineering education in some domestic universities may lack in education quality and program relevance. Graduates from these universities may not have equivalent qualifications as international graduates. It is considered that most of the 12 domestic universities organize their subjects according to the certificate of accreditation standard and to the traditional subjects of chemistry in the 'Department of Chemical Engineering' or 'Department of Chemical and Biological Engineering Chemical and Biological Engineering'. However, due to the increase in the number of overlapping subjects with other majors because of the movement towards academic diversity, the integrity of the chemical engineering curricula is at risk. In addition, after surveying the major and research areas of the department professors, it has been found that there is a shortage of professors who have majored in chemical engineering. Therefore, there is a concern that students may lack understanding of the core principles of chemical engineering. The results of the analysis of the curricula of overseas research universities (including non-certified universities) are as follows. Although the chemical engineering industry in developed countries like the United States and Europe is advancing and changing very quickly, the chemical engineering education in these countries is highly focused on traditional subjects and other related subjects in order to cultivate traditionally trained chemical engineers. The Department of Chemical Engineering at overseas universities still maintains the academic integrity of the chemical engineering field. This is a significant suggestion for our country. On the other hand, domestic universities are changing the name of their chemical engineering major, or even if the name is maintained, they are fusing their curriculum with other majors such as material engineering. Therefore, it is very necessary at this point to start a discussion regarding the integrity of the department of chemical engineering in Korea. We hope that the departments of chemical engineering in domestic universities maintain the integrity of traditional chemical engineering while operating the curriculum within the scope of the standards of the engineering education certification system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1148-1157
• /
• 2022

The maritime safety act defines a large vessel as a vessel of at least 200m in length overall. Since this standard was introduced in 1986, it has not been revised even though the marine traf ic environment has changed significantly. The length overall of 200m is equivalent to the handymax class for a dry bulker; therefore, classifying this as a modern large vessel size is difficult. Meanwhile, according to the maritime safety act, the specific sea area for traffic safety is established where large vessels frequently pass. Accordingly, by reviewing maritime-related laws, this study confirmed that standards for vessels larger than 200m in length overall were already introduced. Furthermore, by examining the statistics of vessels entering Korean ports, the existence of sea areas with a lot of traffic by large vessels, except the current 5 specific areas, was confirmed. Therefore, the following were suggested: the deletion of the term large vessel, a raise in the standard for length of a vessel related to a specific sea area in the maritime safety act.

• Environmental and Resource Economics Review
• /
• v.33 no.1
• /
• pp.1-32
• /
• 2024

The emissions trading system stands as a pivotal climate policy in Korea, incentivizing abatement equivalent to 87% of total emissions (as of 2021). As the system likely has a far-reaching impact, it is crucial to understand how the real economic activity, energy sector, as well as environment would be influenced by its implementation. Employing a macroeconometric model, this paper is the first study analyzing the effects of the Korean emissions trading policy. It interconnects the Korean Standard Industrial Classification (Economy), Energy Balance (Energy), and National Inventory Report (Environment), enhancing its real-world explanatory power. We find that a 50% increase in emission permit price over four years results in a decrease in greenhouse gas emissions (-0.043%) and downward shifts in key macroeconomic variables, including real GDP (-0.058%), private consumption (-0.003%), and investment (-0.301%). The price increase in emission permit is deemed crucial for achieving greenhouse gas reduction targets. To mitigate transition risk associated with price shocks, revenue recycling using auction could ensure the sustainability of the economy. This study confirms the comparative advantage of expanded current transfers expenditure over corporate tax reduction, particularly from an economic growth perspective.

• Analytical Science and Technology
• /
• v.17 no.4
• /
• pp.355-362
• /
• 2004

Fission products and Inter reaction layer of $U_3Si-Al$ dispersion fuel, irradiated in HANARO research reactor with 121 kW/m of maximum liner power and 63 at% of average burn-up, was characterization by EPMA (Electron Probe Micro Analyzer). The fuel punching system developed by Irradiated Materials Examination Facility (IMEF) has used to make these samples for the EPMA. With this system a very small and thin specimen which is 1.57 mm in diameter and 2 mm in thickness respectively has been fabricated to protect the EPMA operator from high radioactive fuel and to mini-mize the equivalent dose rate less than 150 mSv/h. EPMA was performed to observe layers of sectional, Inter-reaction and oxide with specimens of cutting and polished. Stoichiometry in the Inter-reaction layer with $16{\mu}m$ of thickness was $U_{2.84}$ Si $Al_{14}$ with calibration of $UO_2$ and $U_{3.24}$ Si $Al_{14.1}$ with calibration of standard specimen. metallic precipitates in this layer were not observed using fission products examination.