• 소성∙가공
• /
• 제30권5호
• /
• pp.242-246
• /
• 2021

Aluminum alloy sheet is being applied to automobiles continuously for the purpose of reducing car body weight. However, due to low formability, there's a limit to application of products with a deep forming depth such as door inner parts. Therefore, the difficult-to-form parts are mainly segmented formed then joined together, which is also disadvantageous as it increases the cost of manufacturing. This study proposes a hybrid cold-hot stamping method for the 1-piece door inner part to reduce cost. To design the stamping process, numerical simulation method is established by using the temperature-dependent mechanical properties of AA6016. The formability according to the hybrid cold-hot stamping method is evaluated using numerical analysis. The suitability of the proposed stamping method is then verified through the stamping tryout.

• 대한기계학회논문집A
• /
• 제29권2호
• /
• pp.350-359
• /
• 2005

Finite element method is a very effective method to simulate the forming processes with good prediction of the deformation behaviour. For the finite element modeling of sheet mental forming the accurate die model is required. Among finite element method, the static-implicit finite element method is applied effectively to analyze real-size auto-body panel stamping processes, which include the forming stage. This study is about analyzing the stamping process problems by using AutoForm commercial software which used static-implicit method. According to this study, the results of simulation will give engineers good information to access the die design of optimization.

• 소성∙가공
• /
• 제10권2호
• /
• pp.123-129
• /
• 2001

This study is to investigate the effects of cold forming method with steel sheet of SCP3C to improve continuous productivity. Experiments were carried out in various working conditions, such as the number of stamping and the punch temperature. The effects of the punch temperature and the number of stamping on drawability of steel sheet of SCP3C as well as clearance and draw-in in the number of stamping were examined and discussed. More improvement of continuous productivity in case of cold stamping rather than by conventional stamping at room temperature is obtained. The optimum forming condition for drawing trunk floor panel of SCP3C is shown as the punch is cooled by coolant of $-5^{\circ}C$ and at the same time both the die and the blankholder are heated by stamping and frictional heat.

• 소성∙가공
• /
• 제21권8호
• /
• pp.485-492
• /
• 2012

As the shape of stamped part is complicated and as the trend toward light weight continues, the higher level of difficulty is required in making stamping die because of inevitably poor formability. The poor formability can be improved if the material flow during the stamping is carefully controlled. Application of drawbead became commonsense used to retard metal flow of blank into the die cavity at the region where wrinkle is expected. In the study, the concept of beadless stamping process is proposed and the method how to realize the beadless stamping process is presented. The validity of the proposed method is confirmed by the application of the real auto part.

• 소성∙가공
• /
• 제24권1호
• /
• pp.13-19
• /
• 2015

For an accurate analysis of hot stamping, a coupled simulation with different aspects of the process(i.e. mechanical, thermal, and phase transformation) is needed. However, coupled simulations are time consuming and costly. Therefore, the current study proposes a simplified method focused on the forming for the hot stamping simulation of a coupled torsion beam axle (CTBA) tubular beam. In this simplified method, non-isothermal conditions were assumed and only conduction was considered, since it represents the majority of the heat transfer during hot stamping. In addition, temperature and strain rate effects were also included. Moreover, an isothermal simulation was conducted and compared with a non-isothermal simulation. Finally, the simulations were verified by experiments. In conclusion, the proposed method is shown to be effective for the development of tube-type parts, and it effectively predicts the deformation of the tubular beam during hot stamping.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.350-358
• /
• 2020

Hot stamping is an effective and suitable process widely used in automotive applications, though critical issues such as the transfer of the coating materials and build-up of these materials on tool surfaces have been encountered. Past researches figured out the resultant wear phenomenon using pin-on-disc and drawing (for example, strip drawing and deep drawing) methods to mimic the process and analyzed the wear behavior with respect to the influencing factors such as surface coating, load, and roughness. Although the pin-on-disc is a conventional and widely-used method, it presented a methodological limitation when simulating the hot stamping process by forming a new blank each time, and hence, a drawing-based friction method has been proposed and developed. Each drawing method applies loads in a different way, resulting in a different wear behavior. Notably, the deep drawing process is most similar to the hot stamping process compared to other drawing methods. In this paper we present a review of the friction testing methods mimicking the hot stamping process and the associated wear behavior. This can be helpful in presenting a step-by-step approach and different perspectives on the wear behavior in the hot stamping process.

• 소성∙가공
• /
• 제4권1호
• /
• pp.17-27
• /
• 1995

The tact switch is widely used in electric and electronic products. The dome type tact spring is produced by stamping. Stamping of the tact spring and operation of the tact switch have been simulated by the elasto-plastic finite element method. The operating characteristics of the switch may be given by the relation between the operating force and stroke. For a given material, this is affected by two main factors. One is the geometry of dome spring which is determined by the geometry of stamping dies and the stamping pressure, and another one is the dimension of switch. From the calculation, it was possible to obtain the stamping conditions and switch dimension for a predetermined force-stroki relation And, the hoop stresses and effective strains distributions due to the stamping and during the operation of the switch indicate a possibility of cracking in the center and rim of dome spring.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1410-1413
• /
• 2004

Finite element method is very effective method to simulate the forming processes with good prediction of the deformation behaviour. For the finite element modeling of sheet mental forming the accurate tool model is required. Due to the geometrical complexity of real-size part stamping tools it is hard to make FE model for real-size auto-body stamping parts. In this paper, it was focussed on the drawability factors on auto-body panel stamping by AUTOFORM with using tool planning alloy to reduce law price as well as high precision from Design Optimization of die. According to this study, the results of simulation will give engineers good information to access the Design Optimization of die.

• 대한기계학회논문집A
• /
• 제29권3호
• /
• pp.484-494
• /
• 2005

Finite element method is very effective method to simulate the forming processes with good prediction of the deformation behaviour. For the finite element modeling of sheet mental forming the accurate tool model is required. Due to the geometrical complexity of real-size part stamping tools it is hard to make FE model for real-size auto-body stamping parts. In this paper, it was focussed on the drawability factors on auto-body panel stamping by AUTOFORM with using tool planing alloy to reduce law price as well as high precision from Design Optimization of die. According to this study, the results of simulation will give engineers good information to access the Design Optimization of die.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.138-141
• /
• 2004

Finite element method is very effective method to simulate the forming processes with good prediction of the deformation behaviour. For the finite element modeling of sheet mental forming the accurate tool model is required. Due to the geometrical complexity of real-size part stamping tools it is hard to make FE model for real-size auto-body stamping parts. In this paper, it was focussed on the drawability factors on auto-body panel stamping by AUTOFORM with using tool planing alloy to reduce law price as well as high precision from Design Optimization of die. According to this study, the results of simulation will give engineers good information to access the Design Optimization of die.