• 대한기계학회논문집
• /
• 제6권4호
• /
• pp.301-307
• /
• 1982

The purpose of this investigation is to study heat transfer characteristics at a stagnation point on a flat plate caused by upward impinging water jet. At the stagnation point, heat transfer results by impinging water jet are being compared with the ones with supplementary water. Optimum supplementary water quantity are supplied in order to improve the effect of heat transfer for each nozzle-to-plate distance. As the nozzle outlet velocity increases, the heat transfer coefficient at stagnation point consequently increases. Changing the nozzle-to-plate distance, growth rate of heat transfer also varies accordingly. This optimum range of Reynolds number is obtained to improve heat transfer effect.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권1호
• /
• pp.37-42
• /
• 1997

Turbulent flow characteristics of a two - dimensional oblique plate impinging jet(OPIJ) were experimentally investigated. The jet mean velocity and turbulent intensity profIles were also measured along the plate. The jet Reynolds numbers(Re, based on the nozzle width)ranged from 10, 000 to 35, 000, the nozzle - to - plate distance(H/B) from 2 to 16, and the oblique angle (a) from 60 to 90 degree. It has been found that the stagnation point shifted toward the minor flow region as the oblique angle decreases and the position of the stagnation point nearly coin¬cided with that of the maximum turbulent intensity.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.753-760
• /
• 1999

Experiments were conducted to investigate the effect of the initial turbulent intensity on the flow and heat transfer characteristics for a two-dimensional impinging jet. A square rod was installed at the nozzle exit to increase initial turbulent intensity. A hot wire probe and thermochromic liquid crystal technique were used to measure the turbulent intensity and the surface temperature. All measurements were made over a range of nozzle-to-plate distance from 1 to 10 at Re=20,000. When the rod is not installed, the maximum stagnation point Nusselt number is occurred at H/B=9. A higher initial turbulent intensity enhanced the heat transfer on the surface. A correlation between stagnation point Nusselt number and turbulent intensity are presented.

• Nuclear Engineering and Technology
• /
• 제49권8호
• /
• pp.1636-1644
• /
• 2017

The main purpose of this article is to describe the magnetohydrodynamic stagnation point flow of Walter-B nanofluid over a stretching sheet. The phenomena of heat and mass transfer are based on the involvement of thermal radiation and chemical reaction. Characteristics of Newtonian heating are given special attention. The Brownian motion and thermophoresis models are introduced in the temperature and concentration expressions. Appropriate variables are implemented for the transformation of partial differential frameworks into sets of ordinary differential equations. Plots for velocity, temperature, and nanoparticle concentration are displayed and analyzed for governing parameters. The skin friction coefficient and local Nusselt and Sherwood numbers are studied using numerical values. The temperature and heat transfer rate are enhanced within the frame of the thermal conjugate parameter.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권4호
• /
• pp.429-435
• /
• 1998

Experiments were conducted to investigate the turbulent flow characteristics from on oblique impingement surface to an plane jet at the jet Reynolds number(Re based on the nozzle width) $3{\times}10^4$ The jet mean velocity and turbulent intensity profiles have been measured along the impingement surface by hot-wire anemometer. The nozzle-to-plate distance(H/B) ranged from 2 to 10 and the oblique angle (a) from 45 to 90 degree. Also the secondary peak of the turbulent intensity was observed at H/B=4 S/B 5 and a=90 degree. It has been found that the stagnation point shifted toward the minor flow region as the oblique angle decreased and the position of the stagnation point nearly coincided with that of the maximum turbulent intensity.

• 설비공학논문집
• /
• 제23권11호
• /
• pp.754-761
• /
• 2011

The present study numerically investigates two-dimensional flow and heat transfer in the multiple confined impinging slot jet. Numerical simulations are performed for the different Reynolds numbers(Re=100 and 200) in the range of nozzles from 1 to 9 and height ratios(H/D) from 2 to 5, where H/D is the ratio of the channel height to the slot width. The vector plots of velocity profile, stagnation and averaged Nusselt number distributions are presented in this paper. The dependency of thermal fields on the Reynolds number, nozzle number and height ratio can be clarified by observing the Nusselt number as heat transfer characteristic at the stagnation point and impingement surface. The Nusselt number at the stagnation point of the central slot shows unsteadiness at H/D=3 and Re=200. The value of Nusselt number at the stagnation point of the central slot decreases with higher Reynolds number and number of nozzle although overall area averaged Nusselt number increases. Hence careful selection of geometrical parameters and number of nozzle are necessary for optimization of the heat transfer performance of multiple slot impinging jet.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.453-456
• /
• 2011

합성가스를 이용한 충돌제트 버너에서 신장된 예혼합 화염의 열전달 특성에 관한 실험적 연구를 수행하였다. 본 연구에서는 석탄을 가스화하는 과정에서 추출되는 수소와 일산화탄소를 혼합한 합성가스를 연료로 사용하였다. 정체점에서의 열유속은 전체 신장율이 증가함에 따라 증가하다 다시 감소하는 것이 관찰되었다. 또한 정체점에서의 열유속이 노즐로부터 충돌판까지 거리가 증가함에 따라 증가하는 것을 확인하였다. 본 연구는 석탄에서 발생하는 부생가스의 주성분인 수소와 일산화탄소를 실용화하는 연구 중 기초 연구이다.

• 대한기계학회논문집B
• /
• 제30권12호
• /
• pp.1164-1172
• /
• 2006

Measurements of the local heat transfer coefficients on hemispherical convex and concave surfaces with a turbulent impinging jet were made. The Reynolds number used was 11000, 23000, 50000 and the nozzle- to- surface distance was L/d=2, 4, 6, 8, and 10 and the jet angle was a = $0^{\circ}$, $15^{\circ}$, $30^{\circ}$ and $40^{\circ}$. In case of concave surface, the Nusselt number at the stagnation point decreases as the jet angle increases and has the maximum value for L/d=6. The X-axis Nusselt number distributions exhibit secondary maxima at $0^{\circ}$ $\leq$ a $\leq$ $15^{\circ}$, L/d $\leq$ 4 for X/d<0(upstream) and at $0^{\circ}$ $\leq$ a $\leq$ $40^{\circ}$, L/d $\leq$ 4 and at $30^{\circ}$ $\leq$ a $\leq$ $40^{\circ}$, 4 < L/d $\leq$ 6 for X/d<0(downstream). The secondary maximum occurs at long distance from the stagnation point as the jet angle increases or the nozzle-to-surface distance decreases. In case of convex, correlations of the stagnation point Nusselt number according to Reynolds number, jet-to-surface distance ratio and dimensionless surface angle are presented. In the stagnation point, in term of Ren, n ranges from 0.43 in case of 2 $\leq$ L/d $\leq$ 6 to 0.45 in case of 6 < L/d $\leq$ 10, there agrees roughly appears to be laminar boundary layer result. The maximum Nusselt number, in this experiment, occurred in the direction of upstream. The displacement of the maximum Nusselt number from the stagnation point increases with increasing surface angle or decreasing nozzle-to-surface distance. On this condition about surface curvature D/d=10, the maximum displacement is about 0.7 times of the jet nozzle diameter. The ratio of the maximum Nusselt number to the stagnation Nusselt number increases as the jet angle increases.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.57-63
• /
• 2004

A two-dimensional direct numerical simulation was performed to investigate the flame behaviors of $CH_4/N_2$-Air counterflow nonpremixed flame interacting with a single vortex. The detailed transport properties and a modified 16-step augmented reduced mechanism based on Miller and Bowman's detailed reaction mechanism are adopted in this calculation. The results showed that an initially flat stagnation plane, on which an axial velocity was zero, was deformed into a complex-shaped plane, and an initial stagnation point was moved far away from a vortex head when the counterflow field was perturbed by the vortex. It was noted that the movement of stagnation point could alter the species transport mechanism to the flame surface. It was also identified that the altered species transport mechanism affected the distributions of the mixture fraction and the scalar dissipation rate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1690-1696
• /
• 2003

A two-dimensional direct numerical simulation is performed to investigate the flame structure of $CH_4/N_2$-Air counterflow nonpremixed flame interacting with a single vortex. The detailed transport properties and a modified 16-step augmented reduced mechanism based on Miller and Bowman's detailed chemistry are adopted in this calculation. The results show that an initially flat stagnation plane, where an axial velocity is zero, is deformed into a complex-shaped plane, and an initial stagnation point is moved far away from vortex head when the counterflow field is perturbed by the vortex. It is noted that the movement of stagnation point can alter the mechanism of reactants (fuel and oxidizer) fluxes into the flame surface, and then can alter the flame structure.