• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1690-1695
• /
• 2003

In order to investigate the mechanism of brake squeal noise, the sound and vibration of an actua1 brake system were measured using a brake dynamometer. The experimental results show that disc run-out varies with brake line pressure and the factor of squeal generation is the run-out due to the misalignment of brake disk. A three degrees of freedom friction model is developed for the disk brake system where the run-out effect and nonlinear friction characteristic are considered. The results of numerical analysis of the model agree well with the experimental results. Also, the stability analysis of the model was performed to predict the generation of brake squeal due to the design parameter modification of brake systems. The results show that the squeal generation depends on the nm-out rather than the friction characteristic between the pad and the disk of brake.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.362-367
• /
• 2010

This paper deals with the correlation between the interior noise and the floor vibration of the train from rolling, impulse and friction in Busan Metro line 3. The correlation is verified by sound and vibration measurement causing friction between the railway and the wheel. If ANC(Active Noise Control) system can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 1.8-4.8 dB in squeal noise. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.820-825
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, finite element parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and simulation results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type instability is investigated by using the parametric rotor simulation. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the FEM model and establish confidence in the simulation results. Also they may be useful during real disk brake model.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.751-752
• /
• 2010

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.79-84
• /
• 2001

The motivation behind this work is to understand the phenomenon of friction-induced vibration and squeal due to misalignment. In present paper, it is studied on effect of misalignment between friction-induced vibration and squeal by an experiment using a pin-on-disk type experimental apparatus. In order to build an analytical model of the friction-induced vibration system with misalignment, the system is modeled as a single-DOF and 3-DOF system. The results show that the single DOF system can only show stick／slip phenomenon, but the 3-DOF system can show squeal due to misalignment. Consequently, it can be said that the misalignment in a friction-induced vibration system is a source of squeal noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.601-606
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, lumped and distributed parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the theoretical model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and theoretical results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type instability is investigated by using the parametric analysis. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the analysis model and establish confidence in the analysis results. Also they may be useful during system development or diagnostic analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.8
• /
• pp.702-708
• /
• 2004

This paper deals with friction-induced vibration of disc brake system under constant friction coefficient. A linear, lumped and distributed parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the theoretical model, the experimental modal test and the dynamometer test are performed. The comparison of experimental and theoretical results shows a good agreement and the analysis indicates that mode coupling due to friction force is responsible for disc brake squeal. And squeal type Instability is Investigated by using the parametric analysis. This indicates parameters which have influence on the propensity of brake squeal. This helped to validate the analysis model and establish confidence in the analysis results. Also they may be useful during system development or diagnostic analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.604-605
• /
• 2008

Modal participation factor (MPF) is a widely used in a mode-coupling squeal noise problem for finding the most sensitive component over a complex brake system in a vehicle using eigenvectors of sub-components. This methodology requires the problematic total response of system by the unstable squeal noise at a specific frequency as well as eigenvectors of each component belonging to brake system. In this paper, a unit-force response analysis is performed for intact total system to obtain eigenvectors of each component and then such data is directly used for the contribution analysis of a squeal noise problem. Since the eigenvectors of each component induced from virtual unit-excitation is most reliable owing to the intact boundary condition, it can be expected that the corresponding contribution analysis with MPF also provides a trustworthy result.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.8
• /
• pp.717-724
• /
• 2013

The present study provides the numerical results in association with caliper stiffness and friction curve. From the numerical results, it is concluded that the pad vibration modes with dominant displacement in rotation direction is sensitive in the flutter instability. Particularly, the pad rigid mode is shown to become the squeal mode when the caliper stiffness is introduced in brake squeal model. Therefore, the caliper contact stiffness between the pad and caliper is expected to contribute to the squeal modes of the brake pad.

• Journal of Environmental Science International
• /
• v.15 no.3
• /
• pp.287-292
• /
• 2006

The purpose of this paper is to evaluate the noise level and source, reduce the subway line II noise. As a result of measurement of subway line II in Busan the highest value section of uproad line was from Jigegol to Motgol by 89 dB(A). The sections of conversation and listening interference(over 80 dB(A)) were 21 sections(55%) of 38 sections. Among these sections, 15 sections(71%) were produced rolling noise, 3 sections(14%) squeal noise, 2 sections(10%) braking noise and 1 section(5%) fan noise, and then a main noise source was the rolling noise. In case of downroad line, the highest value section was from Busan Metro Art Museum to Centum city, Motgol to Jigegol by 88 dB(A). The sections of conversation and listening interference(over 80 dB(A)) were 18 sections(47%) of 38 sections. Among these sections, 15 sections(83%) produced rolling noise, 2 sections(11%) squeal noise and 1 section(6%) braking noise were investigated in this study. and then a main noise source was the rolling noise.