• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.812-818
• /
• 2000

We studied the effects of Ge preamorphization (PAM) on 0.25$\mu\textrm{m}$ Ti-salicide junctions using comparative study with As PAM. For each PAM schemes, ion implantations are performed at a dose of 2E14 ion/$\textrm{cm}^2$ and at 20keV energy using $^{75}$ /As+and GeF4 ion sources. Ge PAM showed better sheet resistance and within- wafer uniformity than those of As PAM at 0.257m line width of n +/p-well junctions. This attributes to enhanced C54-silicidation reaction and strong (040) preferred orientation of the C54-silicide due to minimized As presence at n+ junctions. At p+ junctions, comparable performance was obtained in Rs reduction at fine lines from both As and Ge PAM schemes. Junction leakage current (JLC) revels are below ~1E-14 A/$\mu\textrm{m}^{2}$ at area patterns for all process conditions, whereas no degradation in JLC is shown under Ge PAM condition even at edge- intensive patterns. Smooth $TiSi_2$ interface is observed by cross- section TEM (X- TEM), which supports minimized silicide agglomeration due to Ge PAM and low level of JLC. Both junction break- down voltage (JBV) and contact resistances are satisfactory at all process conditions.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.184-188
• /
• 2001

Using a DC-sputter and changing the substrate temperature to room temperature and 200$\^{C}$, we manufactured each Co-22%Cr alloy thin-films, which has a uniform micro-structure at room temperature, and a fine self-organized nato structure (SONS) at the inside of the grain at the elevated temperature. We also investigated the microstructure and domain structure using a transmission electron microscope (TEM) and a magnetic force microscope (MFM). We managed to corrode selectively Co-enriched phase, then investigate the microstructure using a TEM. We found that it has a uniform composition when it is manufactured at room temperature, but, we found that it has a unique microstructure, which has a plate-like fine Co-enriched phase, with the formation of SONS at the inside of the grain at the elevated temperature. In MFM characterization, we found maze-type domains at the period of 5000 when the substrate temperature maintains at room temperature. We define that the maze-type domain has a disadvantage at the high density recording because it generates noises easily as the exchange coupling energy between the grains is big. On the other hand, there is only a fine domain structure at the period of 500 when the substrate temperature maintains at 200 $\^{C}$. We define that the fine domain structure has an advantage at the high density magnetic recording because it has thermal stability due to small exchange coupling energy.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.189-195
• /
• 2001

We prepared TMR junctions of NiFe(170 )/CoFe(48 )/Al(13 )-O/CoFe(500 )/Ta(50 ) structure on 2.5$\times$2.5 $\textrm{cm}^2$ area Si/SiO$_2$ substrates in order to investigate the uniformity of magnetoresistance(MR) value using a ICP magnetron sputter. Each layer was deposited by the ICP magnetron sputter and tunnel barrier was formed by the plasma oxidation method. We measured MR ratio and resistance of TMR devices with four-terminal probe system by applying external magnetic field. Although we used ICP sputter which is known as superior to make uniform films, the standard variation of MR ratio was 2.72. The variation was not dependent on the TMR devices location of a substrate. We found that MR ratio and spin-flip field (H's) increased as the resistance increased, which may be caused by local interface irregularity of the insulating layer. The variation of resistance value was 64.19 and MR ratio was 2.72, respectively. Our results imply that to improve the insulating layer fabrication process including annealing process to lessen interface modulation in order to mass produce the TMR devices.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.211-216
• /
• 2001

Top synthetic spin valves wi th structure Ta/NiFe/CoFe/Cu/CoFe(Pl)/Ru/CoFe(P2)/FeMn/Ta on Si (100) substrate with SiO$_2$ of 1500 were prepared by dc magnetron sputtering system. We have changed only the thickness of the free layer and the thickness difference (Pl-P2) in the two ferromagnetic layers separated by Ru, and investigated the effect of magnetic film thickness on the GMR properties and the interlayer coupling field in a spin valve with a synthetic antiferromagnet. As thickness difference of pinned layer was decreased from +25 to -25 , MR ratio was decreased gradually. However, there was a dip zone indicating a big change of MR ratio around Pl = P2, which can be due to the large canting of pinned layers. The modified Neel model was suggested for the top synthetic spin valve to explain the interlayer coupling field according to the thickness change of ferromagnetic layers. The interlayer coupling field was decreased due to the magnetostatic coupling (orange peel coupling) as suggested by model. However, the interlayer coupling field was not explained at the dip zone by the modified Neel model. The deviation of modified Neel model at the dip zone could be due to the largely canting of the pinned layers as well, which depends on different thickness in synthetic antiferromagnetic structure.

• Journal of the Korean Magnetics Society
• /
• v.14 no.3
• /
• pp.89-94
• /
• 2004

We have investigated magnetic properties of monolayer (ML)-thickness Co film deposited on InP(2${\times}$4) reconstruction surface using in situ Surface Magneto-Optical Kerr Effects (SMOKE) measurement system. InP(2${\times}$4) reconstruction surface, obtained by repeated sputtering and annealing, was confirmed by reflection hish energy electron diffraction (RHEED) and scanning tunneling microscope (STM) measurements. From both longitudinal and polar SMOKE measurements, we have observed three distinguishable regions showing different magnetic properties depending on the Co thickness. In the Co film thickness smaller than 7 $m\ell$, no SMOKE signal was detected. In the following thickness between 8 $m\ell$ and 15 $m\ell$, both longitudinal and polar Kerr hysteresis loops were observed, which implies a metastable phase coexisted of in-plane and perpendicular anisotropies. In the film thickness larger than 16 $m\ell$, only longitudinal MOKE signal without polar signal was detected, which implies existence of in-plane anisotropy in this thickness region.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.196-202
• /
• 2000

Top synthetic spin valves with structure Ta/NiFe/CoFe/Cu/CoFe(P1)/Ru/CoFe(P2)/FeMn/Ta on Si(100) substrate with natural oxide were prepared by dc magnetron sputtering system, and investigated on the magnetoresistance properties and effective exchange bias field. As the thickness of FeMn increased above 150 $\AA$, MR ratio was decreased due to the current shunting effect. As the thickness of free layer decreased below 40$\AA$, MR ratio was reduced rapidly. In case of 40 $\AA$ thick of free layer, spin valve film with a structure Si(100)/Ta(50 $\AA$)/NiFe(27 $\AA$)/CoFe(13 $\AA$)/Cu(26 $\AA$)/CoFe(30 $\AA$)/Ru(7 $\AA$)/CoFe(15 $\AA$)/FeMn(100 $\AA$)/Ta(50 $\AA$) exhibited maximum MR ratio of 7.5 % and an effective exchange bias field of 600 Oe, respectively. Thickness difference dependence in this synthetic spin valve structure on effective exchange field was investigated and interpreted by the analytical method. It should be noted that thickness increase of CoFe(P 1) and decrease of CoFe(P2) in synthetic antiferromagnet leaded to the decrease in effective exchange bias field by experimentally and analytically.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.203-209
• /
• 2000

Top synthetic spin valves with structure Ta/NiFe/CoFe/Cu/CoFe(P 1)/Ru/CoFe(P2)/FeMn/Ta on Si (100) substrate with natural oxide were prepared by dc magnetron sputtering system. We have changed only the thickness in free layers and the thickness difference (Pl-P2) in two ferromagnetic layers separated by Ru, and investigated the effect of magnetic film thickness on interlayer coupling field in spin valve with synthetic antiferromagnet. According to the decrease of free layer thickness, interlayer coupling field was increased due to the magnetostatic coupling(orange peel coupling). In case of t$\_$P1/>t$\^$P2/, interlayer coupling field agreed well with the modified Neel model suggested in conventional spin valve structures by Kools et al. However, in case of t$\_$P1/>t$\^$P2/, it was found that the interlayer coupling field was not explained by the Modified Neel Model and was confirmed the necessity of further remodeling. The dependence of Cu thickness on the interlayer coupling field was investigated and 10 Oe of interlayer coupling field was obtained when the Cu thickness is 32 $\AA$.

• Journal of the Korean Magnetics Society
• /
• v.16 no.3
• /
• pp.157-162
• /
• 2006

In this study, a high sensitive giant magnetoresistance-spin valve (GMR-SV) bio-sensing device with high linearity and very low hysteresis was fabricated by photolithography and ion beam deposition sputtering system. Detection of the Fe-hemoglobin inside in a red blood and magnetic nanoparticles using the GMR-SV bio-sensing device was investigated. Here a human's red blood includes hemoglobin, and the nanoparticles are the Co-ferrite magnetic particles coated with a shell of amorphous silica which the average size of the water-soluble bare cobalt nanoparticles was about 9 nm with total size of about 50 nm. When 1 mA sensing current was applied to the current electrode in the patterned active GMR-SV devices with areas of $5x10{\mu}m^2 $ and $2x6{\mu}m^2 $, the output signals of the GMRSV sensor were about 100 mV and 14 mV, respectively. In addition, the maximum sensitivity of the fabricated GMR-SV sensor was about $0.1{\sim}0.8%/Oe$. The magnitude of output voltage signals was obtained from four-probe magnetoresistive measured system, and the picture of real-time motion images was monitored by an optical microscope. Even one drop of human blood and nanopartices in distilled water were found to be enough for detecting and analyzing their signals clearly.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.330-332
• /
• 2013

소 분위기에서 플라즈마 표면 처리의 경우 기판 표면에 존재하는 수소와 탄소 유기물들이 산소와 반응하여 $H_2O$와 $CO_2$ 등으로 제거되며 표면에 오존 결합을 유도하여 표면 에너지를 증가시키는 것으로 알려져 있다. ZnO 나노구조물을 성장시키는 방법으로는 MOCVD (Metal-Organic Chemical Vapor Deposited), PLD (Pulsed Laser Deposition), VLS (Vapor-Liquid-Solid), Sputtering, 습식화학합성법(Wet Chemical Method) 방법 등이 있다. 그중에서도 습식화학합성법은 쉽게 구성요소를 제어할 수 있고, 저비용 공정과 낮은 온도에서 성장 가능하며 플렉서블 소자에도 적용이 가능하다. 그러므로 본 연구에서는 플라즈마 표면처리에 따라 표면에너지를 변화하여 습식화학합성법으로 성장시킨 ZnO nanorods의 밀도를 제어하고 photolithography 공정 없이 패터닝 가능성을 유 무를 판단하는 연구를 진행하였다. 기판은 Si wafer (100)를 사용하였으며 세척 후 표면에너지 증가를 위한 플라즈마 표면처리를 실시하였다. 분위기 가스는 Ar/$O_2$를 사용하였으며 입력전압 400 W에서 0, 5, 10, 15, 60초 동안 각각 실시하였다. ZnO nanorods의 seed layer를 도포하기 위하여 Zinc acetate dehydrate [Zn $(CH_3COO)_2{\cdot}2H_2O$, 0.03 M]를 ethanol 50 ml에 용해시킨 후 스핀코팅기를 이용하여 850 RPM, 15초로 5회 실시하였으며 $80^{\circ}C$에서 5분간 건조하였다. ZnO rods의 성장은 Zinc nitrate hexahydrate [$Zn(NO_3)_2{\cdot}6H_2O$, 0.025M], HMT [$C6H_{12}N_4$, 0.025M]를 deionized water 250 ml에 용해시켜 hotplate에 올리고 $300^{\circ}C$에서 녹인 후 $200^{\circ}C$에서 3시간 성장시켰다. ZnO nanorods의 성장 공정은(Fig. 1)과 같다. 먼저 플라즈마 처리한 시편의 표면에너지 측정을 위해 접촉각 측정 장치[KRUSS, DSA100]를 이용하였다. 그 결과 0, 5, 10, 15, 60 초로 플라즈마 표면 처리했던 시편이 각각 Fig. l, 2와 같이 $79^{\circ}$, $43^{\circ}$, $11^{\circ}$, $6^{\circ}$, $7.8^{\circ}$로 측정되었으며 이것을 각각 습식화학합성법으로 ZnO nanorods를 성장 시켰을 때 Fig. 3과 같이 밀도 차이를 확인할 수 있었다. 이러한 결과를 바탕으로 기판의 표면에너지를 제어하여 Fig. 4와 같이 나타나며 photolithography 공정없이 ZnO nanorods를 패터닝을 할 수 있었다. 본 연구에서는 플라즈마 표면 처리를 통하여 표면에너지의 변화를 제어함으로써 ZnO nanorods 성장의 밀도 차이를 나타냈었다. 이러한 저비용, 저온 공정으로 $O_2$, CO, $H_2$, $H_2O$와 같은 다양한 화학종에 반응하는 ZnO를 이용한 플렉시블 화학센서에 응용 및 사용될 수 있고, 플렉시블 디스플레이 및 3D 디스플레이 소자에 활용 가능하다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.110-110
• /
• 2016

금속재료 중 철강은 기계적 성질이 우수하고 대량생산에 의한 뛰어난 경제성을 가지기 때문에 다양한 산업 분야에서 널리 사용되고 있다. 그러나 스테인리스강 등과 같은 일부 특수한 용도의 강을 제외하고는 부식 환경에 취약하기 때문에 그 용도에 따라 표면처리를 함으로서 내식특성을 부여하고 있다. 일반적으로 이러한 철강재료에 대한 부식문제를 해결하기 위한 방법으로는 습식프로세스 중 아연(Zn)도금이 사용되는데, 아연은 그 자체가 보유하고 있는 차폐(barrier)효과는 물론 상대적으로 이온화 경향이 크기 때문에 철에 대하여 전자를 공급하는 희생양극적(Sacrificial anode)역할을 하여 철을 방식하는 원리를 가지고 있다. 하지만 최근에 이르러 기존의 도금 프로세스 처리된 제품의 사용 및 적용분야가 확대되고 가혹해 짐에 따라서 내식성 향상을 위한 새로운 재료 및 신기술 개발이 요구되고 있는 실정이다. 본 연구에서는 친환경 프로세스 방법인 PVD법 중 하나인 스퍼터링(Sputtering)을 이용하여 0.8mm 두께의 냉연강판 (cold rolled steel) 상에 Al에 대한 Mg 함량을 10~30wt.%로 하여 약 $5{\mu}m$ 두께의 막을 제작하였다. 이때 20wt.% 막의 경우 공정압력조건을 증가시켜 증착 막의 결정배향성을 변화시켰다. 뿐만 아니라 제작된 막들에 대해서 $400^{\circ}C$온도에서 10분간 열처리함으로서 코팅막의 성분변화에 따른 영향을 살펴보기 위해 시편을 추가 제작하였다. 이와 같이 제작된 막들에 대한 형성메커니즘과 내식성의 상관관계 해명을 위해 막의 조성분포, 표면 및 단면의 모폴로지 관찰 및 결정구조 등 재료특성분석과 더불어 염수분무(Salt spray test), 침지시험 그리고 양극분극 시험 등을 통해 내식성 평가를 진행하였다. 이상의 종합적인 결과를 살펴보면 제작된 Al-Mg 막은 마그네슘 함량비 및 열처리 조건에 따라 조성분포와 막의 모폴로지 및 결정배향성이 변화한다는 것을 알 수 있었는데, 마그네슘 함량이 증가하고 열처리한 막의 내식성이 가장 양호한 것으로 나타났다. 이것은 Al-Mg 성분이 표면을 중심으로 균일 분산-분포하며, Al에 대한 Mg의 고용으로 인해 안정적으로 형성된 부식생성물과 금속화합물의 단계적 반응 효과에 의해 차폐효과와 희생양극적 특성이 동시에 향상되었기 때문으로 생각된다. 한편 공정 압력을 증가시켜 형성한 막은 결정학적 구조에서 보다 높은 표면 에너지와 증가한 격자 정수에 의해 Mg이 부식환경에서 빠르게 반응하여 안정적 피막을 형성하기 때문에 내식성이 향상된 것으로 보여 진다. 이상의 연구를 통해서 고내식성을 Al-Mg막의 유효성 확인하였으며, 설계에 대한 기초적인 응용지침을 제시할 수 있을 것으로 사료된다.