• Korean Journal of Agricultural Science
• /
• v.7 no.2
• /
• pp.156-168
• /
• 1980

The air-center nozzles, being specially designed to supply air into the central part of water stream at seven levels of air volume, were tested for spray deposit pattern and flow-rate at each of the twelve pressure levels ranging from $0.35kg/cm^2$ (5 psi) to $6.33kg/cm^2$ (90 psi) in comparison with those of standard nozzles. The air-center nozzles produced comparatively more stable spray deposit patterns than the standard nozzles. The spray deposit patterns of the air-center nozzle were concentrated gradually in the central region with increase of air volume as a component of spray mixture. The degree of concentration of spray deposit on the central region from the air-center nozzle was higher than that of the standard nozzle, which suggested the possibility of obtaining farther travel distance spraying system at a given performance level. The flow rate of the air-center nozzle was not as much as that of the standard nozzle due to the air within certain limits. The rate of decrease of water flow became smaller with an increase in operating pressure although it changed rapidly in the beginning stage, ranging up to two or three percent of the air flow rate due to the compressive properties of air.

• Korean journal of applied entomology
• /
• v.40 no.4
• /
• pp.327-335
• /
• 2001

In order to establish a whitefly control system using conventional groups of insecticide(carbamate, organophosphorus and pyrethroid insecticides), three alternative application methods were designed on the medium growth stage of cucumber. To discriminate the effectiveness of these sequences observed were the residual activity of insecticides, frequency of insecticide applications, residue of insecticides in cucumber leaves, development of insecticide resistance in whitefly, and yield of fruits. Spraying furathiocarb, a carbamate insecticide, was very effective in reducing the frequency of application for the control of white flies. The effectiveness of furathiocarb was enhanced by the potentiation process to carbofuran, the long residual activity, and the lower development rate of insecticide resistance. Methion, an organophosphorus insecticide, did not show resistance development after successive use but resulted in short residual activity. However, other organophosphates, profenofos and phenthoate, lost their activity by the resistance development. Decreasing activity was common to pyrethroids, deltamethrin and zetacypermethrin due to resistance. From these results it could be drawn a conclusion that furathiocarb, a carbamate insecticide, was the most desirable among conventional insecticide groups for the management of greenhouse whitefly population on the cucumber. To prevent an outbreak of the insect pest by various cause, it was recommended to choose acetamiprid, a nicotinoid, which showed very good control efficacy to the resistance insects to conventional insecticides.

• Journal of Internet of Things and Convergence
• /
• v.8 no.2
• /
• pp.35-40
• /
• 2022

In the agricultural environment, pesticide control requires a high risk of work and a high labor force for farmers. The effectiveness of pesticide control using unmanned aerial vehicles varies according to climate, land type, and characteristics of unmanned aerial vehicles. Therefore, an effective method for pesticide control by unmanned aerial vehicles considering the spraying conditions and environmental conditions is required. In this paper, we propose an efficient pesticide control system based on agricultural unmanned aerial vehicles considering the application conditions and environmental information for each crop. The effectiveness of the proposed model was demonstrated by measuring the drop uniformity of pesticides according to the change in altitude and speed after attaching the sensory paper and measuring the penetration rate of the drug inside the canopy according to the change in crop growth conditions. Experiment result, the closer the height of the UAV is to the ground, the more evenly the crops are sprayed, but for safety reasons, 2m more is suitable, and on average a speed of 2m/s is most suitable for control. The proposed control system is expected to help develop intelligent services based on the use of various unmanned aerial vehicles in agricultural environments.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.4
• /
• pp.193-198
• /
• 2021

Recently, interests in the 4th industry have increased the level of demand for pest control by farmers in the field of rice farming, and the interests and use of agricultural pest control drones. Therefore, the diversification of agricultural control drones that spray high-concentration pesticides and the increase of agricultural exterminators due to the acquisition of national drone certifications are rapidly developing the agricultural sector in the drone industry. In addition, as detailed projects, an effective platform is required to construct large-scale big data due to pesticide management, exterminator management, precise spraying, pest control work volume classification, settlement, soil management, prediction and monitoring of damages by pests, etc. and to process the data. However, studies in South Korea and other countries on development of models and programs to integrate and process the big data such as data analysis algorithms, image analysis algorithms, growth management algorithms, AI algorithms, etc. are insufficient. This paper proposed an online drone pest control management information platform to meet the needs of managers and farmers in the agricultural field and to realize precise AI pest control based on the agricultural drone pest control processor using drones and presented foundation for development of a comprehensive management system through empirical experiments.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.3
• /
• pp.186-192
• /
• 2023

According to the regulation on the pollution of the marine environment, SOx emission from ships has to be reduced. A SOx scrubbing system installed in a funnel of a ship is considered in order to reduce SOx emission. A scrubbing layer with a porous material is present in the funnel to increase the contact area between exhaust gas and water. In this study, experiments on the pressure drop characteristics in the scrubbing layer are conducted to investigate the effect of the scrubber on the engine load. The pressure drop according to flow rate of air instead of exhaust gas was measured for fillers such as sphere, pall ring and saddle in the scrubbing layer. First of all, porosity is experimentally measured for the three types of filler and it is confirmed that the porosity of the saddle-type filler was the largest. The pressure drop according to the change in air flow rate was measured for the three types of fillers in the scrubbing layer. As a result, the pressure drop was the smallest in the scrubbing layer with the saddle-type filler which has the largest porosity. In addition, the effect of spraying water flowing counter flow against air flow is experimentally examined. It is known that the pressure drop is increased because the air flow space is reduced when water is sprayed. In the case of the saddle, the pressure drop is about 1.5 to 2 times greater than that when only air flows at the optimum exhaust gas-water injection ratio.

• Resources Recycling
• /
• v.9 no.4
• /
• pp.16-27
• /
• 2000

In order to produce raw material powder of advanced magnetic material by spray roasting process, newly modified spray roasting system was developed in this work. In this spray roasting system, raw material solution was effectively atomized and sprayed into the reaction furnace. Also, uniform temperature distribution inside reaction furnace made thermal decomposition process fully completed, and produced powder was effectively collected in cyclone and bag filter. This system equipped with apparatus which can purify hazard produced gas. In this study complex acid solution was prepared by dissolution of mill scale and ferro-Mn into the acid solution, and the pH of this complex acid solution was controlled about to 4. It was conformed that mill scale and ferro-Mn containing a lot of impurities such as $SiO_2$, P and Al could be used as raw material by reducing the impurities content of complex acid solution below 20 ppm. Complex oxide powder of Fe-Mn system was produced by spraying purified complex acid solution into the spray roaster through nozzle, and the variations of produced powder characters were studied by changing he reaction conditions such as reaction temperature, the injection velocity of solution and air, nozzle tip size and concentration of solution. The morphology of produced powder had spherical shape under the most experimental conditions, and concentration of solution. The morphology of produced powder has spherical shape under the most experimental conditions, and the composition and the particle size distribution were almost uniform, which tells the excellence of this spray roasting system. The grain size of most produced powder was below 100 nm. From the above results, it will be possible to produce ultra fine oxide powder from the chloride of Fe, Mn, Ni, Cu and rare earth by using this spray roasting system, and also to produce ultra fine pure metal powder by changing reaction atmosphere.

• The Korean Journal of Pesticide Science
• /
• v.19 no.3
• /
• pp.329-334
• /
• 2015

With 86 isolates of Botrytis cinerea obtained from diseased fruits of tomato, strawberry and cucumber, it was conducted to detect the fungicide resistance of B. cinerea against mepanipyrim through an agar dilution method. FGA medium was used for monitoring the resistance. Among 86 isolates of B. cinerea, resistant isolates were composed by 23.3%, which was different according to regions isolating the pathogen. In accordance with isolation region, the isolation frequency of resistant isolates was as follows; that of Gyeonggi, Gyeongnam/Pusan and chungnam was 28.6%, 33.3% and 12.8%, respectively. The resistant isolates of B. cinerea showed the cross resistance between mepanipyrim and pyrimethanil. Also the pathogenicity of B. cinerea resistant to mepanipyrim was high as like that of sensitive isolates. Because of them, it should be necessary to manage the spraying system of mepanipyrim and the monitoring for the fungicide resistance.

• Research in Plant Disease
• /
• v.18 no.4
• /
• pp.338-348
• /
• 2012

Potato late blight caused by Phytophthora infestans Cooke is one of the major diseases in the cultivation of potatoes in Korea. Effect of chitosan preparations (SH-1 and SH-2) was evaluated on the inhibition of mycelial growth of P. infestans, and protective activity using detached potato leaf assay both in vivo and in the field test. SH-1 and SH-2 were showed protective activity of young plant with control values more than 95% potato late blight by inoculation with pathogens under growth chamber conditions. Mycelial growth was inhibited the radial growth over 74% at a concentration of $300{\mu}g/ml$ of both SH-1 and SH-2. Spraying with SH-1 and SH-2 on the leaves for detached leaf assay reduced disease development. The content of total polyphenol in stem was significantly increased by SH-1 and SH-2 application in the field. In field experiments, foliar application with both SH-1 and SH-2 were significantly reduced the development of late blight on potato plants. Control of late blight disease was obtained with control values of 72% and 53% by application of 1% SH-1 and SH-2, respectively, with 4 times at 7 days interval, and reduced with similar disease control values by application with 3 times at 14 days interval compared with untreated control. SH-1 and SH-2 applications increased the fresh weight of potato, and higher grade potatoes were also increased. The results showed that SH-1 and SH-2 applications can be used as eco-friendly natural fungicide for organic farming for the increase of yields and control of late blight.

• Horticultural Science & Technology
• /
• v.28 no.6
• /
• pp.1072-1077
• /
• 2010

Plant diseases including gray mold caused by Botrytis cinerea are often reduced when calcium compounds are used as alternative materials in paprika. However, much less information is available about the effects of calcium compounds on controlling of $B.$ $cinerea$. Seven calcium compounds such as calcium sulfate dihydrate, calcium chloride, calcium nitrate, calcium oxide, calcium hydroxide, calcium carbonate, and calcium hydride were evaluated for their effectiveness against $B.$ $cinerea$ on potato dextrose agar medium. The pH of selected calcium compounds was higher (pH 8.2-10) than that of the control (pH 6.6). Calcium carbonate, calcium oxide, calcium hydride, and calcium hydroxide among seven calcium compounds were more effectively inhibited the growth of $B.$ $cinerea$ than other calcium compounds. In the case of spraying the spore suspension on paprika applied with the selected four calcium compounds and supplied with the selected calcium supplements in a hydroponic culture system, the paprika treated with calcium compounds showed less severity of disease than those untreated plants. On the basis of our results, we propose that the suppressive effects of calcium compounds on $B.$ $cinerea$ in paprika resulted from the supply of calcium and a certain degree of salt stress.

• Journal of the Korean Institute of Gas
• /
• v.24 no.3
• /
• pp.33-39
• /
• 2020

In general, in a batch reaction process in which products are made using flammable liquids, splash filling is used to clean the walls of the reactor by spraying flammable liquids, which are raw materials used for product, during cleaning of the reactor after work. During this process, mist of flammable liquid is generated, the lower limit of explosion is lowered, and fire·explosion may occur due to discharges caused by various types of complex charges, such as flow charge, collision charge, and ejection charge. Therefore, based on the recent accident case, to identify the risk when working in the form of splash filling with toluene in a batch process and perform an explosion impact analysis using the TNT equivalent method After that, we will analyze the accident results and suggest preventive measures such as constant purge system, improvement of cleaning method, and use of tantalum to prevent such accident.