• 플랜트 저널
• /
• 제9권2호
• /
• pp.46-50
• /
• 2013

최근 발전회사들은 연료비 절감 방안으로 석탄화력발전소의 연료로 저열량탄 사용을 확대하고 있다. 하지만, 저열량탄 사용으로 비용절감이라는 장점을 가져오는 반면, 발열량이 낮은 탄종 연소 시 터빈에 공급되는 증기온도보다 높은 온도의 연소가스량 증가로 인한 대류열전달이 증가되어 재열기 온도 상승을 초래하게 되었다. 재열기 온도 상승은 재열기 튜브 피로증가와 발전소 효율 저하요인인 재열저감수 사용의 결과를 가져오게 된다. 따라서 재열기 출구온도와 관계된 운전변수들을 분석하여 재열기 출구온도를 적정하게 유지하여 재열저감수 사용량을 절감할 수 있는 방안에 관하여 논하였다.

• Journal of Biosystems Engineering
• /
• 제42권4호
• /
• pp.258-264
• /
• 2017

Purpose: This study determines the spray characteristics and effective spray width of a tractor-mounted commercial boom sprayer through experiments. Methods: Performance tests were conducted to investigate the spray characteristics of the nozzles on a commercial boom sprayer. The flow rate and spray width of a single nozzle were measured at three levels of spray pressure (0.5, 0.7, and 1.0 MPa) and spray height (15, 30, and 45 cm), respectively. The average value of three repetition tests was used as the representative value. A coefficient of variation (CV) was used as an index of spray uniformity, and the width that guarantees CV values of approximately 15% was determined as the effective spray width. The spray characteristics of the overall boom sprayer were derived analytically by superimposing the spray characteristics of a single nozzle. Results: The test results for a single nozzle showed that the spray width tended to increase as the spray height and spray pressure increased. The effective spray width for a single nozzle was the largest at a spray pressure of 1.0 MPa and spray height of 45 cm, which resulted in a coverage of 84 cm of width. The effective spray width for the entire boom sprayer was also the largest at the spray pressure of 1.0 MPa and spray height of 45 cm, with a magnitude of 424.5 cm. The chemical spraying work in an actual field was simulated by applying a spray width of 400 cm. As a result of the operation for three swaths, the CV value was less than 10% for 1,200 cm of the overall spray width, which meant that uniform application was achieved. Conclusions: It was reasonable to set the effective spray width of the boom sprayer used in this study to 400 cm.

• 한국분말재료학회지
• /
• 제3권4호
• /
• pp.227-232
• /
• 1996

(i) The development of a metallurgical bond during the spray forming of clad products has offered the possibility of manufacturing large rolls, including those used in hot and cold strip mills. Small rolls are already being produced in Japan. (ii) Technical developments, including the use-of-multi-atomizers have resulted in the elimination of porosity from the internal bore of a sprayed tube. Bimetallic tubing can also be manufactured and the installation of a 4.5 ton tube plant in the USA should provide low operation costs. (iii) Spray forming offers a potentially low cost manufacturing route for superalloy ring/casing components in high strength superalloys. (iv) A large pilot plant has been built for the spray forming of ultra-clean superalloys for turbine disc applications. (v) Using twin-atomizing technology, special steel billets have been spray formed up to 400mm diameter with deposition yields in excess of 90%. (vi) Al/Si alloy extrusion billets with excellent dimensional tolerances are being manufactured for large scale automotive applications. Several new aluminum alloys have also been developed, including high strength, low density and low cocfficient of expansion materials. (vii) New copper alloys have been developed and pilot plants are in operation to produce these alloys once markets have become established.

• 한국전산유체공학회지
• /
• 제11권4호
• /
• pp.56-61
• /
• 2006

Numerical simulation has been performed to investigate the characteristics of the mist flow through the fire suppression nozzles. The commercial CFD software, FLUENT with the proper modeling was applied for analyzing both the internal and external flow of the spray nozzles. Computations were made for the full cone nozzle in the operation range of the low pressure and high flow-rate. To validate the present computational procedure, numerical results are compared with measurements in terms of K-factor, SMD, axial spray velocity and spray angles. Numerical results suggested that the present numerical model can be used as an adequate tool for a design purpose of mist-spray nozzles.

• 문화기술의 융합
• /
• 제9권4호
• /
• pp.569-576
• /
• 2023

농업용 드론은 경제적 효율성으로 인해 활용도가 점차 증가하고 있으며, 비행을 담당하는 본체와 약제를 방제 대상까지 전달하는 임무를 담당하는 분무 시스템으로 구성되어 있다. 따라서 드론을 활용한 농약 방제 작업 시 농작물에 대한 환경과 특성이 고려되어야 하며, 이에 따른 체계화된 비행 고도, 속도 및 분사 시간 등 조건이 달라져야 한다. 농업용 드론을 이용한 방제 작업은 조종자의 운용에 의존하고 있으며, 운용 숙련도에 따라 살포 효과 및 영향에 차이가 발생한다. 또한 농업용 드론에 관해 운용 기준 및 방제 효율 등의 편차가 발생하여 방제 작업 분야에서 농업용 방제 드론의 보급을 저해하는 요소로 작용하고 있다. 이에 본 연구에서는 농업용 드론의 살포 특성을 파악하여 유효 살포 시간 및 간격을 적용하고, 선행 연구와 비교하여 방제면적 산출이 가능한 체계를 실험적으로 검증하려 한다. 이러한 실험적 검증을 통해 농업용 드론에 운용 방식 및 체계화된 수치를 적용하여, 방제 작업의 저해요인을 최소화하여 최적의 방제 공정을 적용하고자 한다.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.32-42
• /
• 1998

Lean burn gasoline engine is recognized as a promising way to meet better fuel economy. Lean burn engine is classified into port injection and direct injection(DI), DI is more active technique for improving fuel economy with ultra-lean operation, Nowadays, port injected lean burn engine has been produced by many Japan maker. Also, DI engine is also possible for production owing to improvement in control technique of spray, flow air fuel ratio. DI engine uses either homogeneous stoichiometric mixture or stratified mixture by controlling injection timing to be early or late respectively. HM(homogeneous mixture) is worse than SM(stratified mixture) in view of ultra-lean operation in partical load and Nox reducion by using EGR control. But, HM has advanteges in cold starting and emission reduction during transient operation, This paper describes experimental variables and bench test results of HM GDI engine.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.24-29
• /
• 2003

Deep sea water has cold temperature, abundant nutrients and minerals, and good water quality that is pathogen-free and stable. Compared with surface water, deep sea water contains more nutrition salt, such as nitrogen and phosphor. Moreover, if has the good balance of minerals. Because of the ability of the spray drying process to produce a free-flowing power considering of spherical particles with a well-defined size distribution and the rapid drying times for heat-sensitive material, spray drying is attractive for a wide range of applications spray drying is a unique unit operation in which powders are produced from a liquid feed in a single processing step. Key component of the process are atomizer, spray chamber. Design of spray chamber should be based on the atomizer type, the production rate, and the particle size required. Because of the complex processes taking place during spray drying, traditional design method are based on pilot-plant tests and empirical scale-up rules. Modern technique such as CFD have a role to play in design and troubleshooting.

• 자원리싸이클링
• /
• 제11권5호
• /
• pp.24-29
• /
• 2002

철강압연공장에서 산세공정중 발생하는 산화철의 색상을 개선하기 위하여 배소로 조업과 색상혼합공정을 연구하였다. 배소로 조업에서는 조업온도, 폐산장입량, 폐산분사 노즐수에 대하여 검토하였으며, 색상혼합공정에서는 산화티탄, 실리카, 괴타이트를 색상혼합재로 검토하였다. 배소로 조업에서는 조업온도를 낮게 할수록 산화철의 명도가 개선되었으며, 색상혼합공정에서는 괴타이트 첨가 경우에 제일 많이 산화철의 적색 및 명도가 개선되었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제24회 KOSCO SYMPOSIUM 논문집
• /
• pp.3-10
• /
• 2002

In this work, numerical parametric studies on spray combustion have been conducted. In simulation of turbulence, RNG ${\kappa}-{\varepsilon}model$ is adopted. Initial spray distribution is specified by Rosin-Rammler distribution function. Eddy break-up model is adopted as a combustion model. The parameters considered are inlet air temperature, swirl number, and SMD. With higher inlet air temperature, the axial velocities are increased and penetration of primary jet is stronger than that of lower inlet air temperature and temperature at the exit of combustor is more uniform. Combustion efficiency is improved with high inlet air temperature. The effect of swirl number on flow field is not significant. It affect only recirculation zone. So temperature at upstream of combustor is influenced. Combustion efficiency deteriorate as SMD of fuel spray increase.

• 한국세라믹학회지
• /
• 제41권5호
• /
• pp.353-358
• /
• 2004

Spray drying is a unique drying process for powder production. Spray dried product must be free-flowing in order to fill the pressing dies rapidly, especially in the ceramic production. The important powder characteristics are; the particle size distribu-tion and moisture content of the finished product that can be estimated and adjusted by the spray dryer operation, within limits, through regulation of atomizer and drying conditions. In order to estimate the moisture content of the resultant dried product, we modeled the control system of the drying process using two different Artificial Neural Network (ANN) approaches, namely the Back-Propagation Multiplayer Perceptron (BPMLP) algorithm and the Radial Basis Function (RBF) network. It was found out that the performance of both of the artificial neural network models were quite significant and the total testing error for the 100 data was 0.8 and 0.7 for the BPMLP algorithm and the RBF network respectively.