• Steel and Composite Structures
• /
• 제18권2호
• /
• pp.345-355
• /
• 2015

In this study, the effects of weld parameters on nugget size and tensile-shear strength of welding joint in electrical resistance spot welding of galvanized DP 600 steel sheets having 1.2 mm were investigated. Taguchi design method has been employed to examine the effects of five parameters of welding current, electrode pressure, welding time, clamping time and holding time by using the $L_{27}(5^3)$ orthogonal array. Results showed that the most effective parameters on tensile shear strength and the nugget size ratio (hn/dn) were found as welding current and welding time, whereas electrode pressure, clamping time and holding time were less effective factors. Max. 545 MPa strength was obtained through proposed optimum conditions by Taguchi technique.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1179-1185
• /
• 2011

용접이음부의 신뢰성 확보는 구조물의 건전성과 내구성에 직접적인 영향을 미치기 때문에 점용접 이음재의 피로설계기준(fatigue design criterion)을 정하기 위해서는 정확한 응력해석과 체계적인 피로강도평가가 필요하다. 따라서 본 연구에서는 실제 전동차량 차체에 많이 적용되는 냉간 및 열간압연강판인 SPCC, SPCE, SPHE을 대상으로 기하학적 인자(geometrical factors)들을 선별해서 TS형과 CT형의 대표적인 점용접 이음재 시험편을 기본모델로 하여 인장전단하중을 가하여 피로강도 및 피로특성을 평가하고자 하였다. 그리고 피로균열의 발생과 성장 기구에 대한 영향을 분석하기위해 용접 시 발생되는 여러 가지 주요인자들 중 입열량에 의해 발생할 수 있는 용접잔류응력을 X-ray 회절법에 의해 실험적으로 해석하였다. 그리고 이러한 해석을 통하여 얻어진 결과를 중첩(superposition)함으로 해서 잔류응력을 고려했을 경우 너깃 단 최대주응력으로 피로강도를 재평가하여 합리적인 피로설계기준(fatigue design criterion)을 재정립하고자 하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1243-1248
• /
• 2010

Fatigue design and evaluation of welded joints are typically carried out by weld classification approach in which a family (theoretically infinite) of parallel nominal stress based S-N curves are used according to joint types and loading modes as well as extrapolation-based hot spot stress. Traditional finite element methods are not capable of consistently capturing the stress concentration effects on fatigue behavior due to their mesh-sensitivity in stress determination at welds resulted from notch stress singularity. The extrapolated hot spot stresses tend vary, depending on the element sizes, types, joint types, and loading mode. however, the equilibrium-equivalent structural stress method(E2S2) has been recently developed through several joint industry projects as a robust method to analyze welded components using finite element analysis. This method has been proven effective in correlating a large amount of published fatigue test results in the literature such as master S-N curve and has used for evaluating the fatigue life of welding components. In this study, fatigue analysis of the welding bogie frame is examined using E2S2 method with master S-N curve.

• 한국해양공학회지
• /
• 제6권2호
• /
• pp.21-34
• /
• 1992

The behavior of fatigue crack growth in the single spot welded joint of zinc galvanized steel sheets was studied experimentally and analytically based on fracture mechanics. Axial tension fatigue tests were carried out with the BSxGAB specimen that the bare plane(GAB) of monogalvanized steel sheet was spot welded to the double thickness bare steel sheet(BS), and with the GAxGAB specimen that the galvanized plane (GA) was spot welded to the equal thickness bare plane (GAB) 1. The relation between maximum stress intensity factor, K sub(max) and the number of cycles to failure, N sub(f) has shown a linear relation on log-log plot in the spot weld of the zinc galvanized steel sheet. 2. The fatigue strength of BSxGAB specimens is about 23% higher than that of GAxGAB specimens at the fatigue strength of $1\times10^6$ cycles. And the fatigue life of BSxGAB specimens at the same load range increases 6~9 times higher than that of GAxGAB specimens. 3. The general tendency at the angle of bending($\theta$) in an applied load has changed rapidly at the initial 20% of its life. After then, it has changed slowly. The change at the angle of bending has increased linearly as the load range increases. 4. It has shown a linear relation between the location ratio of initiation ${\gamma}$ and fatigue life $N_f$ on the semi-log graph paper. Here $\gamma$ means that the crack distance between main crack and sub-crack, 2L is divided by the nugget diameter, 2r. $\gamma=a{\cdot}log N_f+n$ (where a and n are material constant.)

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.49-54
• /
• 2015

Welding process is of importance to assemble products or structures, but also the process is structural weakness due to stress concentration in welding joint. The fatigue design of welded joint requires time & labor consuming fatigue test because the fatigue life is various according to the depth of joint, joint type and load type etc. In fatigue design codes, they guide to classify welding joints with their shape( BS7608, IIW Documents) and provide fatigue assessment information. In terms of numerical method for fatigue analysis, it is also difficult to decide the stress peak in joint because of mesh sensitivity which means that stress value is varies with element type or size on stress concentration zone. Hot-spot method is used generally, but Battelle of United States proposed Master S-N Curve based on structural stresses converted by mechanical equilibrium theory. In this research, we extracted master S-N curve from Battelle's fatigue test DB including test data of various welding joints to apply on Non-Load-Carrying cruciform Joint. Comparing fatigue results between the case of using normal stress and case of structural stress cor the cruciform Joint, The suggested Battelle method showed successive results.

• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.181-196
• /
• 2023

Marine structures including offshore wind turbines (OWTs) always work under cyclic loads, which arouses much attention on the fatigue design. The tripod substructure is one of the typical foundation forms for fixed OWTs. The three-planar tubular Y-joint (3Y joint) is one of the important components in fatigue design as it is most likely to have cracks. With the existence of the multiplanar interaction effect, calculating the hot spot stress (HSS) of 3Y joints is complicated. To assist with fatigue design, the distributions of stress concentration factor (SCF) and multiplanar interaction factor (MIF) along weld toe curves induced by the out-of-plane bending moment are explored in this study. An FE analysis method was first developed and verified against experimental results. This method was applied to build a numerical database including 1920 FE models covering common ranges of geometric parameters. A parametric study has been carried out to reveal the distribution patterns of SCF and MIF. After multidimensional nonlinear fittings, SCF and MIF distribution formulas have been proposed. Accuracy and reliability checking prove that the proposed formulas are suitable for calculating the HSS of 3Y joints.

• 한국재료학회지
• /
• 제19권7호
• /
• pp.369-375
• /
• 2009

The spot weldability of dissimilar metal joints between stainless steels (AISI316) and interstitial free (IF) steels were investigated. This study was aimed to determine the spot welding parameters for a dissimilar metal joint and to evaluate the dissimilar metal joint's weldability, including its welding nugget shape, tensileshear strength, hardness, and microstructure. The fracture surface was investigated by using a Scanning Electron Microscopy (SEM). The experimental results showed that the shape of nugget was asymmetric, in which the fusion zone of the STS316 sheet was larger due to the higher bulk-resistance. The microstructure of the fusion zone was fully martensite. In order to evaluate the microstructure further, dilution of stainless steels were calculated and imposed onto the Schaeffler diagram. The predicted microstructure from the Schaeffler diagram was martensite. In order to confirm the predicted microstructure, XRD measurements were carried out. The results showed that that initial weld nugget was composed of austenite and martensite.

• Journal of Welding and Joining
• /
• 제14권1호
• /
• pp.82-91
• /
• 1996

The maximum butt-joint gap size in $CO_2$ laser beam welding of SAPH steel plates with different thicknesses and its bending formability were studied. In the range of the gap size$\geq$0.1mm, the optimal butt welding speed was faster than that of no gap (air gap) condition. This behaviour was independent on the difference of thickness at any combination. Also, the allowable gap size in steel plates with different thicknesses was larger than with same thicknesses. In the range of $T/T_0$(bead shape) $\geq$ 0.8, good bending formability was obtained at any combination of thickness. The formability was improved by reducing the hardness in weld bead using pre-heating process. Finally, FEM result of the laser beam welded underframe with different thicknesses was compared to that of the conventional spot welded underframe.

• 한국항해항만학회지
• /
• 제26권1호
• /
• pp.43-49
• /
• 2002

본 연구에서는 비감쇠 자유진동을 하는 점용접된 사각평판의 고유진동수를 수치해석을 통하여 살펴보고, 실험을 통하여 결과를 검증하였다 설계변수로는 점용접에 미치는 여러 설계변수 중에서 점용접이 차지하는 면적을 사각평판의 면적으로 나눈 면적비와 점용접점 사이의 거리를 평판의 한 변의 길이로 나눈 거리비로 무차원화하여 사용하였으며, 목적함수로는 점용접으로 인한 두께효과를 진동수에 대한 처짐의 비로써 나타낸 등가두께로써 무차원화하여 정의하였다. 수치해석에는 범용유한요소해석 프로그램인 ANSYS 5.6을 사용하였고, 실험에는 B&K Data analyzer를 통하여 주파수분석을 수행하였다. 연구의 결과 다음과 같은 결론을 얻었다. 1. 점용접의 면적비가 단지 4.52%인데 비해 점 용접으로 인한 두께효과는 55%로써 매우 크게 나타났다. 2. 거리비에 따른 두께효과는 거리비가 0.4일 때 가장 크게 나타났다.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.42-48
• /
• 2010

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) were welded by a combination of a diode laser and a CNC machining center. Laser beam delivered through the transparent PC and was absorbed in an opaque ABS. Polymers were melted and joined by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead and cross-section were analyzed for weld quality, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was measured to be 3.75mm. The shear strength at the given condition was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in a CNC machining system, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision.