• 대한기계학회논문집A
• /
• 제25권7호
• /
• pp.1073-1081
• /
• 2001

Many researches have published numerous papers about the high-strain-rate obtained from Split Hopkinson Pressure Bar(SHPB) tests. And 6.5wt%Si steel is widely known as an excellent magnetic material because its magnetostriction is nearly zero. Single crystals are prepared by the Floating Zone(FZ) method, which melts the alloy by the use of a high temperature electron beam in a pure argon gas condition. In this paper, the fracture behavior of the poly crystals and single crystals (DO$_3$phase) of Fe-6.5wt%Si alloy by SHPB test is observed. The comparison of high-strain-rate results with static results was done. Obtained main results are as follows: (1) Fe-6.5wt%Si alloy has higher strength at high-strain-rate tensile. SHPB results of polycrystal are twice as high as static results. (2) From the fractography, the cleavage steps are remarkably reduced in the SHPB test compared with the static test.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권3호
• /
• pp.69-75
• /
• 2002

Measuring dynamic fracture toughness of brittle and small ceramic specimen is very difficult in a SHPB (Split Hopkinson Pressure Bar). As a countermeasure to this difficulty, a dynamic fracture toughness measuring method by the Chevron-notch ceramic specimen was proposed. Tested chevron specimens were of Chevron notch angles of 90$^{\circ}$, 100$^{\circ}$ and 110$^{\circ}$. Through finite element analysis, shape parameters of the Chevron-notch specimens according to notch angles were calculated. And the static fracture tough1ess of the Chevron-notch alumina specimen was measured as 3.8MPa√m similar to that of CT specimen with a precrack. Dynamic fracture toughness was 4.5MPa√m slightly higher than the static one. It was shown in this study that the proposed Chevron-notch specimens are valid to measure dynamic fracture toughness of extremely brittle materials such as ceramic.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1491-1494
• /
• 2003

A specific experimental method, the Split Hopkinson Pressure Bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s∼104/s. This type of test procedure has been used to examine the dynamic response of materials in various modes of testing. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.981-987
• /
• 2010

Split Hopkinson Pressure Bar(SHPB) 실험기법은 고변형률 하중 조건하에서 변형하는 여러 가지 공업 재료의 변형 거동 특성을 규명하는데 가장 널리 사용되는 실험 방법 중의 하나이다. 본 논문에서는 봉을 통하여 전파하는 응력파의 모양과 라이징 시간을 제어할 수 있는 pulse shaper를 사용하는 수정 SHPB 실험기법을 이용하였다. 수정 SHPB 실험 장치에 고온 장치를 부착하고 알루미늄 합금 7075-T6의 고변형률 하에서의 고온 변형거동에 대한 연구를 수행하였다. 고온 수정 SHPB 실험 장치를 이용하여 알루미늄 합금 7075-T6의 온도와 변형률속도에 따른 기계적 특성을 규명하고, 실험적으로 얻어진 데이터를 Johnson-Cook 구성방정식을 적용하여 알루미늄 합금 7075-T6의 동적 거동을 모델 하는 변수를 결정하였다.

• 대한기계학회논문집A
• /
• 제24권8호
• /
• pp.1917-1922
• /
• 2000

The split Hokinson pressure bar(SHPB) test has been used to find the mechanical property of materials at high strain rate. A tensile split Hopkinson pressure bar test system is developed and the threaded tensile specimen and the split collar are placed between elastic bars. When the compressive elastic wave generated by a striker is transferred from the transmit bar to the incident bar, some elastic wave is reflected at the threaded parts of the specimen and the transmit bar. This reflected wave can interfere with the transmitted wave. A proper length of elastic bars and the location of strain gage in these elastic bars are determined to avoid this interference. In order to avoid the interference of elastic wave reflected at the threaded parts of specimen and elastic bar, the length of transmit bar must be longer than that of incident bar. Strain gage in transmit bar must be located as close as possible from the interface of a transmit bar and specimen. In the developed tensile SHPB test system, A12011-T3 and A17075-T6 are tested to get the true stress-strain relation in the range of strain rate at $10^3/sec$

• 대한기계학회논문집A
• /
• 제34권5호
• /
• pp.511-518
• /
• 2010

SHPB시험은 입력봉과 출력봉 사이에 시편을 위치시키고 고속으로 변형하여 동적 응력-변형률 선도를 추출하는 것이다. 그렇기 때문에, 소재와 입력봉 사이 또는 소재와 출력봉 사이의 마찰이 측정되는 응력-변형률 선도에 영향을 주게 된다. 이것은 측정되는 응력이 유동응력이 아니고 축방향 응력이기 때문임을 확인 하였다. 본 연구에서는 측정되는 축방향 응력을 보정하여 정확한 유동응력을 구하기 위해 새로운 보정식을 제안하였다. 소재가 업셋팅 형태로 변형한다고 가정하고, 에너지 보존에 기초하여 보정식을 제안하였다. ABAQUS를 이용한 수치적 실험을 통해 마찰계수 0.3까지 보정한 결과 보정식이 유용함을 확인하였다.

• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.158-165
• /
• 2003

A specific experimental method, the Split Hopkinson pressure bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain rate of the order of 10$^3$/s∼l0$^4$/s. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from structure under varying dynamic loading are determined by using plastic SHPB technique. A transition point to scope with the dynamic deformation behavior of rubber-like material is defined in this paper and used to characterize the specifics of the dynamic deformation of rubber materials.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.790-794
• /
• 1997

Mechanical properties of the materials used for transportations and industrial machinery under high strain rate loading conditions such as seismic loading are required to provide appropriate safety assessment to those mechanical structures. The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental behavior under high strain rate loading condition In this paper, dynamic deformation behaviors of A15052-H32 under high strain rate tensile loading are determined using the SHPB technique.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.3033-3039
• /
• 2000

Mechanical properties of the materials used for transportations and industrial machinery under high stain rate loading conditions have been required to provide appropriate safety assessment to these mechanical structures. The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental apparatus can be used to obtain the material properties under high strain rate loading condition. There have been many studies on the material behavior under high strain rate compressive loading compared to those under tensile loading. In this paper, mechanical properties of the aluminum alloy, Al6061-T6, under high strain rate tensile loading were determined using SHPB technique.

• 터널과지하공간
• /
• 제18권3호
• /
• pp.214-218
• /
• 2008

본 연구에서는 SHPB(Split Hopkinson Pressure Bar)를 이용하여 변형률 속도에 따른 이방성 화강암의 동적파괴 과정을 조사하였다. 실험결과 변형률 속도가 증가할수록 에너지 흡수량 및 최대응력이 증가하였다. 최대응력은 모든 방향에서 변형률 속도에 의존적이나 역학적 이방성에 민감하지는 않았다. 변형률 속도가 증가할수록 탄성파속도가 많이 감쇠되고, 모든 방향에서 변형률 속도에 의존적이며 강한 암석일수록 감쇠가 빠르게 일어났다.