• International Journal of Aeronautical and Space Sciences
• /
• v.10 no.2
• /
• pp.117-124
• /
• 2009

In the environment where various and complicated threat signals exist, RWR (Radar Warning Receiver), which can warn pilot of the existence of threats, has long been a necessary electronic warfare (EW) system to improve survivability of aircraft. The angle of arrival (AOA) information, the most reliable sorting parameter in the RWR, is measured by means of four-quadrant amplitude comparison direction finding (DF) technique. Each of four antennas (usually spiral antenna) of DF unit covers one of four quadrant zones, with 90 degrees apart with nearby antenna. According to the location of antenna installed in helicopter, RWR is subject to signal loss and interference by helicopter body and structures including tail bumper, rotor blade, and so on, causing a difficulty of detecting hostile emitters. In this paper, the performance degradation caused by signal interference by tail rotor blades has been estimated by measuring amplitude video signals into which RWR converts RF signals in case a part of antenna is screened by real tail rotor blade in anechoic chamber. The results show that corruption of pulse amplitude (PA) is main cause of DF error. We have proposed two algorithms for resolving the interference by tail rotor blades as below: First, expand the AOA group range for pulse grouping at the first signal analysis phase. Second, merge each of pulse trains with the other, that signal parameter except PRI and AOA is similar, after the first signal analysis phase. The presented method makes it possible to use RWR by reducing interference caused by blade screening in case antenna is screened by tail rotor blades.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.1
• /
• pp.39-44
• /
• 2013

In this paper digital phase-shifter for multi-arm spiral antennas was designed by using Hilbert transform. All frequency components in input signal are phase-shifted for 90 degree by Hilbert transform, and the transform is implemented by FIT and IFIT. Digital phase-shifter generates two signals with phase difference of 90 degree by using Hilbert transform from input signals sampled by analog-digital converter(ADC), and then the input signal is phase-shifted for a given phase by using two signals. Hilbert transform based on digital phase-shifter is designed by Xilinx System generator, and the effects of input noise, FIT point, sampling period, initial phase of input signal, and shifted phase are simulated and its results are compared with Matlab results.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.3
• /
• pp.10-15
• /
• 2011

The separation actuator for the small satellite should fix satellite appendages with high clamping force. After operation, it has to be separated from the satellite body without any damage on satellite system and release the appendages such as a solar panel and an antenna successfully. Therefore, we invent a non-explosive separation actuator for the small satellite which generates low shock and is resettable. In order to confirm performance of the proposed separation actuator, we carried out experiments for separation time, maximum preload for activation, and shock level.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.2040-2041
• /
• 2007

In this paper, the UHF PD(Partial Discharge) sensors for $SF_6$ insulated MV $SF_6$ switchgear have been proposed and related investigations have been performed in order to detect the PD which were produced inside the MV $SF_6$ switchgear. Firstly, the internal type UHF PD sensor based on spiral antenna theory has been developed. This type sensor is highly sensitive and has lowly effect on by on-site noise. Secondly, the external type UHF PD sensor was developed based on log periodic antenna concept. This type sensor is removable and detectable for operating switchgear. These sensors were designed and simulated using RF simulation tool. In order to verify the sensitivity of these sensors, we performed the on-site test using the mock-up switchgears including the artificial defects which were the protrusion on high voltage conductor, free moving metal particle and surface defect on insulator. These mock-up switchgear were installed on the test distribution line.

• Radiation Oncology Journal
• /
• v.2 no.1
• /
• pp.11-20
• /
• 1984

The renewed interest in the use of hyperthermia in cancer therapy is bases on radiobiological and clinical evidence indicated that there may be a significant therapeutic advantage with the use of heat alone or combined with radiation or chemotherapy, There are many methods for generating heat for localized tumor as like radiofrequency, microwave, electromagnetic induction and ultrasound. But it is very difficult to be even thermal dose distribution and stable output of power and then the detection of temperature in tumor is difficult to be precise with thermocouples and semiconductor sensors. We designed the microwave heating generator, dipole antenna applicators and autometic temperature controlled thermocouples for localized hyperthermia on skin and in cavities. 1. The microwave generator with 120 W, 2,450MHz magnetron could be heating up to $40^{\circ}C\~50^{\circ}C\;for\;1\~2$ hours in living tissues. 2. The thermal dose distribution in tissue with microwave was described $42^{\circ}C\~44^{\circ}C$ with in 3 cm depth and $2\~6cm$ diameter area. 3. Skin surface heating applicator with spiral 3 times wave length antenna radiated high Power of microwave. 4, Intracavitary heating applicator with dipole antenna with autometic control temperature sensor kept up continuously constant temperature in tissue. 5. For constant thermal distribution, applied two steps power with 10W microwave after $17\~20W$ during first 10 minutes. 6. The cooling rate by blood flew in living tissue was rised as $10\%$ then meats.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.828-833
• /
• 2018

It is well known that reflected waves and resonance affect phase distortion. In addition, phase delay can be distorted by antenna impedance. In this study, we analyze the phase delay variation caused by the antenna impedance, considering mutual coupling effects. In addition, we confirm the beam steering characteristics. When was -10 dB and -7 dB, the maximum phase delay error was $18.5^{\circ}$ and $26.5^{\circ}$, respectively. The Monte Carlo simulation with an eight-element linear array antenna demonstrated that the RMS error of the beam steering angle ranged from $0.19^{\circ}$ to $0.4^{\circ}$, and the standard deviation ranged from $0.14^{\circ}$ to $0.33^{\circ}$ when the beam steering angle was in the range of $0^{\circ}$ to $30^{\circ}$, with the uniformly distributed phase error of $18.5^{\circ}$ and $26.5^{\circ}$. The side lobe level increased from 0.74 dB to 1.21 dB by the phase error from the theoretical value of -12.8 dB, with a standard deviation of 0.31 dB to 0.51 dB. This is verified by designing an eight-element spiral array antenna.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.35-38
• /
• 2005

In this paper, a wideband balun of tapered structure using planar microstrip is desigde ad analyzed. The balun structure was fabricated on a Teflon substrate with a thickness of 0.8mm and relative dielectric constant ${\varepsilon}_r$ of 2.5. Two back-to back CPW-to-CPS transitions were simulated and optimized using HFSS. A movel plaar balun using tapered structure of microstip to CPW is suggested and designed. The measurement result, the bandwidth for a reflection coefficient better than -10dB of the balun is 2GHz to 8GHz. The planar balun can improved the performance of wide band spiral antenna.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.83-90
• /
• 2004

This paper describes investigations of the UHF(Ultra High Frequency) PD(Partial Discharge) measuring technology designed for monitoring of PD in high power apparatus. Based on the spiral antenna theory, the hole type sensor for GIS with metal flange spacer and injection type sensor for oil filled transformer are developed. The experimental results show measurement characteristics of the PD sensor for several artificial defects in gas-insulated system(GIS) and oil transformer. Moreover, we proposed the new $\phi$-f-q method for the purpose of condition assessment of high power apparatus.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.2038-2039
• /
• 2007

In this work, a novel semi-internal type UHF PD sensor has been proposed and related investigations has been performed in order to detect the partial discharges that could be possibly produced at the insulation system of the gas insulated switchgear(GIS). This sensor was designed to mount on the CT terminal hole of GIS using the spiral antenna theory. Therefore this type sensor can be install on GIS during the power apparatus has been operation and better sensitivity compare to the commercial external type UHF PD sensor.

• ETRI Journal
• /
• v.25 no.2
• /
• pp.65-72
• /
• 2003

To achieve cost and size reductions, we developed a low cost manufacturing technology for RF substrates and a high performance passive process technology for RF integrated passive devices (IPDs). The fabricated substrate is a conventional 6" Si wafer with a 25${\mu}m$ thick $SiO_2$ surface. This substrate showed a very good insertion loss of 0.03 dB/mm at 4 GHz, including the conductive metal loss, with a 50 ${\Omega}$ coplanar transmission line (W=50${\mu}m$, G=20${\mu}m$). Using benzo cyclo butene (BCB) interlayers and a 10 ${\mu}m$ Cu plating process, we made high Q rectangular and circular spiral inductors on Si that had record maximum quality factors of more than 100. The fabricated inductor library showed a maximum quality factor range of 30-120, depending on geometrical parameters and inductance values of 0.35-35 nH. We also fabricated small RF IPDs on a thick oxide Si substrate for use in handheld phone applications, such as antenna switch modules or front end modules, and high-speed wireless LAN applications. The chip sizes of the wafer-level-packaged RF IPDs and wire-bondable RF IPDs were 1.0-1.5$mm^2$ and 0.8-1.0$mm^2$, respectively. They showed very good insertion loss and RF performances. These substrate and passive process technologies will be widely utilized in hand-held RF modules and systems requiring low cost solutions and strict volumetric efficiencies.