• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1332-1342
• /
• 2014

This paper proposes a novel test circuit for SiC transistors. On-state resistance under practical application conditions is an important characteristic for the device reliability and conduction efficiency of SiC transistors. In order to measure the on-state resistance in practical applications, high voltage is needed, and high current is also necessary to ignite performance for the devices. A soft-switching circuit based on synchronous buck topology is developed in this paper. To provide high-voltage and high-current stresses for the devices without additional spikes and oscillations, a resonant circuit has been introduced. Using the novel circuit technology, soft-switching can be successfully realized for all the switches. Furthermore, in order to achieve accurate measurement of on-state resistance under switching operations, an active clamp circuit is employed. Operation principle and design analysis of the circuit are discussed. The dynamic measurement method is illustrated in detail. Simulation and experiments were carried out to verify the feasibility of the circuit. A special test circuit has been developed and built. Experimental results confirm that the proposed circuit gives a good insight of the devices performance in real applications.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2011-2016
• /
• 2018

In this study, we have been investigated pin to plate pulsed bi-polar discharges in saline solutions, where bubble generation occurs. We integrate basic I-V-t electrical characteristics with the ICCD shadowgraph images, and finally instant and time averaged I-V waveforms. We observed that the bubble formation phase dynamics is quite different corresponding to the polarity applied to the pin electrode. When the pin electrode is a cathode, the bubble tends to be periodically detached from the pin electrode and the numerous tiny voltage spikes occur related to the electron emission from a pin cathode casing via, we judge from, direct dissociation of water molecules by energetic electrons. On the contrary, the bubble tends to stick to the pin electrode, when the pin electrode is anode; the bubble grows in size throughout the pulse duration. The dynamic electrical characteristics relative to the applied polarity of a pin electrode are presented and discussed by analysis of time averaged I-V waveforms.

• Annals of Clinical Neurophysiology
• /
• v.9 no.2
• /
• pp.69-74
• /
• 2007

Electroencephalogram (EEG) is a representative diagnostic tool in epilepsy. However, there are several points of debate on the role of EEG in diagnosis and management of epilepsy. We suggest that EEG has some limitations for differential diagnosis from nonepileptic episodic diseases, classification of epilepsy, prediction of recurrence, and evaluation of treatment response. Interictal EEG cannot diagnose or exclude epilepsy because interictal epileptic discharge (IED) is frequently absent in epilepsy and can appear in nonepileptic conditions. Although EEG is helpful in classification of epilepsy, focal spikes in generalized epilepsy and secondary bilateral synchrony in localization related epilepsy cause interrater disagreement. It is controversial whether EEG predicts recurrence after the first seizure in adults. The predictive value of EEG in antiepileptic drug (AED) withdrawal is not absolute. The prognosis after AED withdrawal depends on epilepsy syndrome. Many studies could not confirm the value of EEG in assessing the treatment response. After all, epilepsy is clinically diagnosed and assessed. Interictal EEG alone does not provide decisive information and routine follow-up of EEG is not recommended.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.2
• /
• pp.79-84
• /
• 2015

Voltage sags are considered the dominant disturbances affecting power quality. Dynamic voltage restorers(DVRs) are mainly used to protect sensitive loads from the electrical network voltage disturbances such as sags or swells and could be used to reduce harmonic distortion of ac voltages. The typical DVR topology essentially contains a PWM inverter with LC Filter, an injection transformer connected between the ac voltage line and the sensitive load, and a DC energy storage device. For injecting series voltage, the PWM inverter is used and the passive filter consist of inductor(L) and capacitor(C) for harmonics elimination of the inverter. However there are voltage pulsation responses by the characteristic of the LC passive filter that eliminate the harmonics of the PWM output waveform of the inverter. Therefore, this paper presented design and feedback performance of LC filter used in the DVRs. The voltage control by LC filter should be connected in the line side since this feedback method allows a relatively faster dynamic response, enabling the elimination of voltage notches or spikes in the beginning and in the end of sags and strong load voltage THD reduction. Illustrative examples are also included.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1445-1453
• /
• 2017

In this study, a new zero-voltage transition (ZVT) buck converter with coupled inductor using a synchronous rectifier and a lossless clamp circuit is proposed. The regular buck converter with tapped inductor has extended duty cycle for high step-down applications. However, the leakage inductance of the coupled inductor produced considerable voltage spikes across the switch. A lossless clamp circuit is used in the proposed converter to overcome this problem. The freewheeling diode was replaced with a synchronous rectifier to reduce conduction losses in the proposed converter. ZVT conditions at turn-on and turn-off instants were provided for the main switch. The synchronous rectifier switch turned on under zero-voltage switching, and the auxiliary switch turn-on and turn-off were under zero-current condition. Experimental results of a 100 W-100 kHz prototype are provided to justify the validity of the theoretical analysis. Moreover, the conducted electromagnetic interference of the proposed converter is measured and compared with its hard-switching counterpart.

• Nuclear Engineering and Technology
• /
• v.47 no.7
• /
• pp.924-933
• /
• 2015

The correlation of the isotopic composition of uranium, plutonium, neodymium, and cesium with the burnup for high burnup pressurized water reactor fuels irradiated in nuclear power reactors has been experimentally investigated. The total burnup was determined by Nd-148 and the fractional $^{235}U$ burnup was determined by U and Pu mass spectrometric methods. The isotopic compositions of U, Pu, Nd, and Cs after their separation from the irradiated fuel samples were measured using thermal ionization mass spectrometry. The contents of these elements in the irradiated fuel were determined through an isotope dilution mass spectrometric method using $^{233}U$, $^{242}Pu$, $^{150}Nd$, and $^{133}Cs$ as spikes. The activity ratios of Cs isotopes in the fuel samples were determined using gamma-ray spectrometry. The content of each element and its isotopic compositions in the irradiated fuel were expressed by their correlation with the total and fractional burnup, burnup parameters, and the isotopic compositions of different elements. The results obtained from the experimental methods were compared with those calculated using the ORIGEN-S code.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.2
• /
• pp.233-241
• /
• 2021

A series of three bench-scale experiments was performed to investigate the conversion of sodium metal to sodium chloride via reactions with non-metal and metal chlorides. Specifically, batches of molten sodium metal were separately contacted with ammonium chloride and ferrous chloride to form sodium chloride in both cases along with iron in the latter case. Additional ferrous chloride was added to two of the three batches to form low melting point consolidated mixtures of sodium chloride and ferrous chloride, whereas consolidation of a sodium-chloride product was performed in a separate batch. Samples of the products were characterized via X-ray diffraction to identify attendant compounds. The reaction of sodium metal with metered ammonium chloride particulate feeds proceeded without reaction excursions and produced pure colorless sodium chloride. The reaction of sodium metal with ferrous chloride yielded occasional reaction excursions as evidenced by temperature spikes and fuming ferrous chloride, producing a dark salt-metal mixture. This investigation into a method for controlled conversion of sodium metal to sodium chloride is particularly applicable to sodium containing elevated levels of radioactivity-including bond sodium from nuclear fuels-in remote-handled inert-atmosphere environments.

• Advances in aircraft and spacecraft science
• /
• v.6 no.3
• /
• pp.225-238
• /
• 2019

A spike attached to a blunt nosed body significantly alters its flow field and influences the aerodynamic coefficients at hypersonic speed. The basic body is an axisymmetric, with a hemisphere nose followed by a cylindrical portion. Five different types of spikes, namely, conical aerospike, hemisphere aerospike, flat-face aerospike, hemisphere aerodisk and flat-face aerodisk are attached to the basic body in order to assess the aerodynamic characteristic. The spiked blunt body without the aerospike or aerodisk has been set to be a basic model. The coefficients of drag, lift and pitching moment were measured with and without blunt spike body for the length-to-diameter ratio (L/D) of 0.5, 1.0, 1.5 and 2.0, at Mach 6 and angle of attack up to 8 degrees using a strain gauge balance. The measured forces and moment data are employed to determine the relative performance of the aerodynamic with respect to the basic model. A maximum of 77 percent drag reduction was achieved with hemisphere aerospike of L/D = 2.0. The comparison of aerodynamic coefficients between the basic model and the spiked blunt body reveals that the aerodynamic drag and pitching moment coefficients decrease with increasing the L/D ratio and angle of attack but the lift coefficient has increasing characteristics.

• Journal of Soil and Groundwater Environment
• /
• v.26 no.1
• /
• pp.34-44
• /
• 2021

Acid mine drainage (AMD) resulting from pyrite oxidation in mining areas, subsequently leads to soil acidification accompanied by lowering pH and high concentration of metals and metalloids in its surrounding environment. Regarding to this, the microbial amelioration has been considered as a promising option for a more cost-effective and eco-friendlier countermeasure, compared to the use of alkaline chemicals. This study was aimed to evaluate influencing factors in microbially-mediated amelioration of acidic soil spiked by simulated AMD. For this, microcosm experiments were conducted by acid-neutralizing bacterial consortium (dominated by Klebsiella sp. and Raoultella sp.) under the various conditions of AMD spikes (0-2,500 mg SO42-/L), together with acidic mine soil (0-100 g) or sphagnum peat (0-5 g) in the 200 mL of nutrient medium. The employed bacterial consortium, capable of resisting to high level of sulfate concentration (up to 1,500 mg SO42-/L) in low pH, generated the ammonium while concomitantly reduced the sulfate, subsequently contributing to the effective soil stabilization with an evolution of soil pH up to neutral. Furthermore, it demonstrates that suitable condition has to be tuned for successful microbial metabolism to facilitate with neutralization during practical application.

• Journal of Hospice and Palliative Care
• /
• v.24 no.1
• /
• pp.46-55
• /
• 2021

Purpose: This pilot study aimed to examine the influence of death counseling on perceptions, preparedness, and anxiety regarding death and dying among family caregivers of hospice patients. Methods: Death counseling developed based on the SPIKES model was provided to 37 family caregivers in a hospice and palliative care unit. Perceptions, preparedness, and anxiety regarding death were assessed with a self-administered structured questionnaire, and participants' scores before and after counseling were compared using the paired t-test. Results: Significant changes were found in perceptions, preparedness, and anxiety regarding death after counseling. Compared to before counseling, the scores for perceptions of death (t=-4.90, P<0.001) and preparedness for death and dying (t=-16.23, P<0.001) improved, while anxiety (t=3.72, P=0.001) decreased after counseling. Some changes were also found in the types of support that family caregivers needed to prepare for the death of their family members in the hospice care unit. Conclusion: The findings demonstrate that death counseling could help family caregivers prepare for the death of their loved ones. Hospice and palliative care providers should play a key role in supporting family caregivers of hospice patients by developing strategies for counseling.