• 대한전자공학회논문지SD
• /
• 제46권2호
• /
• pp.24-30
• /
• 2009

본 논문에서는 3GPP(Third Generation Partnership Project) Release 7 eHSPA(High Speed Packet Access for Evolution) UE(User Equipment) FDD(Frequency Division Duplex) 규격을 만족하는 단말 모뎀의 FPGA(Field Programmable Gate Array) 플랫폼 설계 및 이를 기반으로 한 효율적인 검증 방법에 대해 제안한다. 구현된 FPGA 모뎀 플랫폼은 물리 계층 지원을 위한 모뎀 보드, MCU(Micro Controller Unit)와 DSP(Digital Signal Processor) 코어로 구성되어 모뎀 보드를 제어를 위한 제어 보드, 그리고 RF(Radio Frequency) 및 기타 장비 접속을 위한 주변장치(Peripheral) 보드 등으로 구성된다. 그리고 검증 단계는 하드웨어-소프트웨어 연동 상관 정도에 따라 단순 기능 검증, 시나리오 검증 그리고 호 처리 및 시스템 성능 검증 등으로 규정화하여 진행되었고, 실제 구현적인 측면으로 저 전력 SoC(System On a Chip)를 위한 에뮬레이션 검증 기법도 제안한다.

• Journal of Welding and Joining
• /
• 제28권5호
• /
• pp.75-79
• /
• 2010

The Remote welding system(RWS) using $CO_2$ laser equipment has focusable distance of laser beam longer than 800 mm from workpiece and can deflect the laser beam by the scanner mirrors very rapidly. In the case of normal welding system based on robot, there is a limit to move the shortest path in short time and this causes interference between robot and workpiece. On the other hand, RWS is the optimized equipment to get big merits with advanced sequence of welding and short cycle time. However, there is still a pending task such as the control of plasma in the welding process of thick sheets therefore, it requires high power laser beam because of the absence of assist gas equipment in itself. In this study, high-tensile steel plates were overlap welded with $CO_2$ RWS for the production of car body and the influence of penetration depth according to the existence of assist gas was analyzed. Excellent tensile strength with enough width of molten zone independent to penetration depth was observed under welding condition with 3.6 kW laser power and 2.8 m/min welding speed without assist gas. Finally, the proto-type automotive parts were produced by applying the deduced optimal welding condition.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.116-122
• /
• 2012

The purpose of this study is to investigate the overall spray behavior characteristics for various injection conditions in a gasoline direct injection(GDI) injector with multi-hole. The spray characteristics, such as the spray penetration, the spray angle, and the injection quantity, were studied through the change of the injection pressure, the ambient pressure, and the energizing duration in a high-pressure chamber with a constant volume. The n-heptane with 99.5% purity was used as the test fuel. In a constant volume chamber, the injected spray was visualized by the spray visualization system, which consisted of the high-speed camera, the metal-halide lamp, the injector control device, and the image analysis system with the image processing program. It was revealed that the injection quantity was mainly affected by the difference between the injection pressure and the ambient pressure. For low injection pressure conditions, the injection quantity was decreased by the increase of the ambient pressure, while it nearly maintained regardless of the ambient pressure at high injection pressure. According to the increase of the ambient pressure in the constant volume chamber, the spray development became slow, consequently, the spray tip penetration decreased, and the spray area increased. In additions, the circular cone area decreased, and the vortex area increased.

• 한국항공우주학회지
• /
• 제33권8호
• /
• pp.56-64
• /
• 2005

모형헬리콥터를 이용한 무인항공기 설계를 위해 비선형 형태의 수학적 모델이 선행되어야 한다. 모형헬리콥터는 실기 헬리콥터에 비해 회전수가 훨씬 높으며 따라서 동특성도 실물기에 비해 훨씬 빠르다는 차이점이 있다. 본 논문에서는 축소형 헬리콥터의 수학적 모델링에 필요한 정식화과정으로서 복잡성을 최소화하면서도 실제의 동특성에 잘 부합하도록 각 구성요소별로 계산한 후 전체로 합산하는 방법을 제시하였다. 제자리 비행과 전진비행에서 수치계산을 통해 트림 값들을 계산하고 제자리 비행조건에서 선형 시스템을 해석하여 모형헬리콥터의 비행모드를 분석하였다. 계산결과 일반적인 경향은 몇 가지 작은 부분 이외에는 대체로 다른 연구결과와 비슷하였다. 이 과정을 검증하기 위해서 비행시험을 수행하여 시스템식별에 의한 결과와 비교하는 연구가 후속 수행될 예정이다.

• Restorative Dentistry and Endodontics
• /
• 제28권3호
• /
• pp.203-208
• /
• 2003

The purpose of this study was to evaluate the effect of salivary contamination of teeth on bonding efficacy of self-priming and self-etching DBSs. The materials used were Single Bond(SB, self-priming system, 3M), Unifil Bond(UB, self-etching system, GC), and Scotchbond Multi-Purpose Plus(SM, 3M) as control. Forty five human molars randomly allocated to three groups as dentin bonding systems tested and embedded in epoxy resin. Then the specimens were wet-ground to expose flat buccal enamel surface or flat occlusal dentin surface and cut bucco-lingually to form two halves with slow speed diamond saw. One of them was used under non-contamination, other under contamination with saliva. The bonding procedure was according to the manufacturer's directions and resin composite(Z-100, 3M Dental Products, St. Paul, MN) was built-up on the bonded surface 5mm high. The specimens were ground carefully at the enamel-composite interface with fine finishing round diamond bur to create an hour-glass shape yielding bonded surface areas of $1.5{\pm}0.1\textrm{mm}^2$. The specimens were bonded to the modified microtensile testing apparatus with cyanoacrylate, attached to the universal testing machine and stressed in tension at a CHS of 1mm/min. The tensile force at failure was recorded and converted to a tensile stress(MPa). Mean values and standard deviations of the bond strength are listed in table. One-way ANOVA was used to determine significant difference at the 95% level. The bond strength of SBMP and SB were not affected by salivary contamination, but that of UB was significantly affected by salivary contamination. These results indicate that DBSs with total etch technique seems less likely affected by salivary contamination in bonding procedure.

• 방송공학회논문지
• /
• 제10권2호
• /
• pp.182-189
• /
• 2005

본 논문에서는 방송과 통신의 융합을 고려한 고속가입자망의 구현을 위해 비대칭 WDM-EPON을 제안하였다. 이 방식에서는 OLT에서 각 가입자 노드로의 하향 전송에는 WDM (Wavelength Division Multiplexing) 전송방식을 이용함으로써 방송 및 다양한 멀티미디어 서비스를 수용하기 위한 넓은 대역폭을 만족하였다. 반면에 넓은 대역폭이 필요하지 않는 상향전송에는 WDM방식보다는 상대적으로 값이 싼 EPON 전송방식을 채택하였다. 본 논문에서는 물리계층에서의 전송시험 결과를 제시한다. ONU가 홈게이트웨이에 이용되기 위해서는 접속 프로토콜은 홈게이트웨이의 트래픽 형태에 적절해야만 한다. 음성의 경우 시간 지연에 민감한 반면 데이터는 덜 민감하다. 본 논문에서는 가입자망에서 다양한 형태의 데이터를 함께 수용할 수 있는 새로운 동적 대역할당 프로토콜을 제시하였으며 이의 성능을 분석하였다. 시간 지연에 민감한 신호의 성능을 보장하기 위해 최대 사이클 타임을 규정하였으며, 하향 제어신호가 급격히 늘어나는 것을 방지하기 위해 최소 윈도우를 규정하였다. 제안된 EPON 프로토콜이 기존 방식에 비해 가지는 장점들을 시뮬레이션에 의해 보였다.

• 세라미스트
• /
• 제21권2호
• /
• pp.4-18
• /
• 2018

Lastly, neuromorphic computing chip has been extensively studied as the technology that directly mimics efficient calculation algorithm of human brain, enabling a next-generation intelligent hardware system with high speed and low power consumption. Three-terminal based synaptic transistor has relatively low integration density compared to the two-terminal type memristor, while its power consumption can be realized as being so low and its spike plasticity from synapse can be reliably implemented. Also, the strong electrical interaction between two or more synaptic spikes offers the advantage of more precise control of synaptic weights. In this review paper, the results of synaptic transistor mimicking synaptic behavior of the brain are classified according to the channel material, in order of silicon, organic semiconductor, oxide semiconductor, 1D CNT(carbon nanotube) and 2D van der Waals atomic layer present. At the same time, key technologies related to dielectrics and electrolytes introduced to express hysteresis and plasticity are discussed. In addition, we compared the essential electrical characteristics (EPSC, IPSC, PPF, STM, LTM, and STDP) required to implement synaptic transistors in common and the power consumption required for unit synapse operation. Generally, synaptic devices should be integrated with other peripheral circuits such as neurons. Demonstration of this neuromorphic system level needs the linearity of synapse resistance change, the symmetry between potentiation and depression, and multi-level resistance states. Finally, in order to be used as a practical neuromorphic applications, the long-term stability and reliability of the synapse device have to be essentially secured through the retention and the endurance cycling test related to the long-term memory characteristics.

• 전력전자학회논문지
• /
• 제3권1호
• /
• pp.1-7
• /
• 1998

발전설비의 대형화로 인하여 전력절감 문제가 크게 대두되었고, 팬이나 펌프를 부하 변화에 따라 속도제어하므로써 전기 에너지를 절약 할 수 있다. 1MVA급 단위 인버터 2대를 병렬 운전하여 대용량 2MVA GTO 인버터를 구현하였으며, 단위 인버터의 병렬 운전은 2대의 출력변압기 2차측 결선을 직렬 연결하여 구현하였다. 개발된 시스템은 제어반, 정류기반, 2대의 인버터반으로 구성되어 있으며, 이 시스템은 한국전력공사 성인천복합화력발전처 해수펌프 구동 유도전동기(6.6KV 1500KW)에 적용되어 전력절감에 기여하고 있다. 또 단위 인버터가 상호 180$^{\circ}$위상차를 갖도록 병렬 운전하므로써 고조파 성분을 저감시키면서 대용량을 구현하였다.

• 한국통신학회논문지
• /
• 제39C권3호
• /
• pp.209-222
• /
• 2014

현대전의 전쟁 개념은 정보 통신 기술의 발전과 함께 지휘 통제 과정을 네트워크로 연계하여 전투 수행 능력을 향상시키는 네트워크 중심전 (NCW, Network Centric Warfare)으로 변화하고 있다. 이에 따라, 네트워크를 통한 정보의 우위를 점유하는 NCW의 구현에 있어, 감시 정찰 체계로부터 획득한 정보정찰감시 (ISR, Intelligence Surveillance Reconnaissance) 정보의 고속 전송을 위해 개발된 공용데이터링크 (CDL, Common Data Link) 기술이 핵심 요소로 고려되고 있다. 세계 각국에서는 CDL의 전송속도 및 네트워킹 기능을 향상시키기 위한 기술 개발에 주력하고 있으며, 우리 군도 자립적인 CDL 기술 개발의 필요성을 인식하고 MPI-CDL (Multi-Platform Image and Intelligence Common Data Link)을 개발하였다. 하지만 다수 체계 간 대용량 ISR 정보를 신속하게 수집 제공하기에는 최대 전송속도 및 네트워킹 기능 성능이 해외 장비 대비 미흡한 상황으로, 전체적인 성능을 향상시킨 차세대 CDL 개발이 필요한 실정이다. 따라서 본 논문에서는 차세대 한국형 CDL 개발을 위해, 현재까지의 CDL 개발 흐름과 해외 선행 장비의 기술 동향을 살펴보고, 향후 지향해야 할 차세대 CDL 개발 방향에 대해 제시한다.

• 산업경영시스템학회지
• /
• 제38권3호
• /
• pp.108-116
• /
• 2015

A missile defense system is composed of radars detecting incoming missiles aiming at defense assets, command control units making the decisions on weapon target assignment, and artillery batteries firing of defensive weapons to the incoming missiles. Although, the technology behind the development of radars and weapons is very important, effective assignment of the weapons against missile threats is much more crucial. When incoming missile targets toward valuable assets in the defense area are detected, the asset-based weapon target assignment model addresses the issue of weapon assignment to these missiles so as to maximize the total value of surviving assets threatened by them. In this paper, we present a model for an asset-based weapon assignment problem with shoot-look-shoot engagement policy and fixed set-up time between each anti-missile launch from each defense unit. Then, we show detailed linear approximation process for nonlinear portions of the model and propose final linear approximation model. After that, the proposed model is applied to several ballistic missile defense scenarios. In each defense scenario, the number of incoming missiles, the speed and the position of each missile, the number of defense artillery battery, the number of anti-missile in each artillery battery, single shot kill probability of each weapon to each target, value of assets, the air defense coverage are given. After running lpSolveAPI package of R language with the given data in each scenario in a personal computer, we summarize its weapon target assignment results specified with launch order time for each artillery battery. We also show computer processing time to get the result for each scenario.