• 대한기계학회논문집A
• /
• 제31권2호
• /
• pp.245-252
• /
• 2007

Since the new millennium, truss PCMs(Periodic Cellular Metals) have drawn attention because of their superior specific stiffness, strength and multi-functionality. Prior studies have focused on the structural design and optimization. Kagome truss PCM has been proved to have the higher resistance to plastic buckling, more plastic deformation energy and lower anisotropy than other truss PCMs. In this study, we introduce a new idea to fabricate multi-layered Kagome truss PCM from continuous wires which can gain high strength as in piano wires and can be controlled to be defect free owing to drawing process. The relative density, the stiffness and the strength under bending and compressive load are estimated through elementary mechanics and compared with the results from experiments and FEA. The failure mechanisms are analyzed, and also mechanical performance and production are discussed.

• 조명전기설비학회논문지
• /
• 제13권1호
• /
• pp.111-118
• /
• 1999

함반영 촉각장치(Force-Reflecting haptic Interface)는 인간이 컴퓨터에 의해 생성한 가상의 세계에 손의 위치 정보를 제공하고 가상의 손이 가상 환경에 접촉했을 때 인간에게 촉각을 전달하는 장치이다. 본 논문에서는 컴플라이언스 제어가 비교적 용이한 초음파 모터 액츄에이터를 사용하여 직접구동 방식으로 촉각장치를 설계하였다. 렌더링 알고리즘을 이용하여 가상의 벽, 가상 버튼, 가상 구멍 등의 기본적인 역감실험을 한 결과 힘 반영에 의한 역감을 제시받을 수 있었다.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.55-62
• /
• 2013

An analytical procedure to determine a proper profile of the spring rail that generates intended contact pressure distribution in the flat wiper blade is introduced. The flat wiper blade is one piece blade and subjected to pressing force at a center point. In this type of blade, contact pressure distribution in the tip of rubber strip is determined by the pressing force, the initial profile of the blade before contact and bending stiffness of the blade. Experimentally obtained bending stiffness of the blade assembly is almost identical to that of the spring rail. Principle of reciprocity has been used to define the initial profile of spring rail from the deformed profile that is assumed to be identical to the windshield glass profile. The procedure has been verified experimentally by measuring the contact pressure of the blade assembled with the spring rail designed by the procedure proposed here. Measured contact pressure distributions of the blades show good agreements with intended distributions over the entire blade span. Consequently, it can be concluded that proposed procedure has relatively good accuracy in developing the spring rail for flat blade having a specific contact pressure distribution.

• Coupled systems mechanics
• /
• 제11권4호
• /
• pp.285-295
• /
• 2022

Laminated composite plates are utilized extensively in different fields of construction and industry thanks to their advantages such as high stiffness-to-weight ratio. Additionally, they are characterized by their directional properties that permit the designer to optimize their stiffness for specific applications. This paper presents a numerical analysis and optimization study of plates made of composite subjected to low velocity impact. The main aim is to identify the optimum fiber orientations of the composite plates that resist low velocity impact load. First, a three-dimensional finite element model is built using LS DYNA computer software package to perform the impact analyses. The composite plate has been modeled using solid elements. The failure criteria of Tsai-Wu's criterion have been used to control the strength of the composite material. A good agreement has been found between the predicted numerical results and experimental results in the literature which validate the finite element model. Then, an Adaptive Simulated Annealing (ASA) has been used to optimize the response of impacted composite laminate where its objective is to maximize the safety factor by varying the ply angles. The results show that the ASA is robust in the sense that it is capable of predicting the best optimal designs.

• 한국전산구조공학회논문집
• /
• 제22권1호
• /
• pp.81-88
• /
• 2009

본 논문은 부재 단위의 강성 재설계를 통해 전역 자유도 변위의 정량적 조절이 가능한 변위조절 기법의 개발을 목적으로 하고 있다. 이를 위해 부분적 강성변경이 발생했을 때 전체 구조물을 재해석하지 않고 관심 있는 특정 위치의 변위와 부재력만을 실시간 응답수준에서 재계산할 수 있는 부분재해석 기법을 적용하였다. 부분재해석 기법은 복잡한 미분계산이나 반복적인 구조해석을 수행하지 않아도 되는 단순한 기본개념의 기법으로서 계산이 효율적이고 강성변경 후의 변위를 바탕으로 변위에 대한 민감도를 계산하기에 수렴 속도가 빠른 장점을 가진다. 부분재해석 기법을 통해 전역 자유도에 대한 강성 변경 부재의 변위기여도를 계산하고 변위기여도에 따라 해당 부재의 강성을 변경시킴으로써 반복적 구조해석이나 민감도 해석 없이 특정 변위를 최소의 물량만으로 정량적으로 제어하는 변위조절 설계법을 제시하였다. 예제를 통한 검증결과, 부분재해석 기법이 고층건물의 횡변위제어에 효과적으로 활용될 수 있음을 확인하였다.

• 한국지반공학회지:지반
• /
• 제14권2호
• /
• pp.67-78
• /
• 1998

마이크로터널링은 비교적 연약한 사질토 지반을 통과하는 소규모의 터널을 시공할 때 적용하는 공법으로, 터널 시작 위치에서 일련의 짧은 원형 콘크리트 관을 유압으로 밀어서 전구간을 관통하는 공법이다. 미국 뉴욕의 JFK공항의 활주로에서는 활주로 하부를 통과하는 전력구의 설치를 위하여 이러한 마이l터널링 공법을 시도하였다. 마이크로터널링 공법에서는 콘크리트관을 전진시키기 위해 강력한 유압으로 벤토나이트를 분출하는데, 이로 인하여 활주로 하부의 지반이 교란될 가능성이 있었기에 본 연구에서는 터널시공으로 인한 교란의 정도를 평가하기 위하여 SASW 기법과 크로스흘 시험을 수행하였다. 구조물 비파괴 건전도 기법인 SASW 기법으로는 활주로 기층 부위의 지반강성 변화 정도를 평가하였고, 크로스흘 시험으로는 활주로 인접 지반의 깊이별 5파속도 변화를 조사하였다. 또한, JFK 공항 부지에서 결정한 5파 속도-N 치의 부지특유 관계식을 통하여 5파 속도를 N치로 변환함으로써 지반강성의 변화를 지반강도 변화의 측면으로도 지반교란의 정도를 파악하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권2호
• /
• pp.113-121
• /
• 1994

Since two oil shocks in 1970s, all of engine makers have persevered in their efforts to reduce specific fuel consumption and to increase engine power rate as much as possible in marine diesel engines. As a result, the maximum pressure in cylinders of these engines has been continuously increased. It causes direct axial vibration. The axial stiffness of crank shaft is low compared to old types of engine models by increasing the stroke/bore ratio and its major critical speed might occur within engine operation range. An axial damper, therefore, needs to be installed in order to reduce the axial vibration amplitude of the crankshaft. Usually the main critical speed of axial vibration for the propulsion shafting system with a 4-8 cylinder engine exists near the maximum continuous revolution(MCR). In this case, when the damping coefficient of the damper is increased within the allowance of the structural strength, its stiffness coefficient is also increased. Therefore, the main critical speed of axial vibration can be moved beyond the MCR. It has the same function as a conventional detuner. However, in the case of a 9-12 cylinder engine, the main critical speed of axial vibration for the propulsion shafting system exists below the MCR and thus the critical speed cannot be moved beyond the MCR by using an axial damper. In this case, the damping coefficient of an axial damper should be adjusted by considering the range of engine revolution, the location and vibration amplitude of the critical speed, the fore and aft vibration of the hull super structure. It needs to clarify the dynamic characteristics of the axial vibration damper to control the axial vibration appropriately. Therefore authors suggest the calculation method to analyse the dynamic characteristics of axial vibration damper. To confirm the calculation method proposed in this paper, it is applied to the propulsion shafting system of the actual ships and satisfactory results are obtained.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.46-53
• /
• 2008

Recently, the synthetic material stern tube bush has been applied by ship owner's requirement because the synthetic material has a merit. That is to say, when stern tube seal is damaged and sea water comes into stern tube, it can work without problem because of water lubricating property. However, the material also has a demerit of temperature rise problem when some factors meets on synthetic material, for example, not sufficient lubrication oil supply and not proper shaft alignment and so on. As known in the world, the RAILKO bush is rampant for synthetic material by some ship owner because of the above mentioned reason. However, the bush has several accidents on large container vessel. Unfortunately or fortunately our yard has a chance to apply the RAILKO bush owing to requirement of specific ship owner. Therefore, it is much more required to approach the accurate shaft alignment analysis. In line with this reason, we had a shaft alignment calculation considering hull deformation and hull flexibility (hull stiffness). Also, in the calculation, we had considered dynamic condition which is reflected he propeller thrust forces and moments and oil film stiffness on the shaft alignment calculation. According to he shaft alignment calculation, bearing slope was applied on the tern tube bush and was measured. The RAILKO bush should be applied the running in procedure according to maker's recommendation for performing the oil film on the bush surface. Finally, the vessels were delivered successfully without any problem with AILKO bush as shown on his paper.

• Steel and Composite Structures
• /
• 제29권4호
• /
• pp.527-544
• /
• 2018

The paper presents the study on a change in modal parameters and structural stiffness of cable-stayed Fiberline Bridge made entirely of Glass Fiber Reinforced Polymer (GFRP) composite used for 20 years in the fjord area of Kolding, Denmark. Due to this specific location the bridge structure was subjected to natural aging in harsh environmental conditions. The flexural properties of the pultruded GFRP profiles acquired from the analyzed footbridge in 1997 and 2012 were determined through three-point bending tests. It was found that the Young's modulus increased by approximately 9%. Moreover, the influence of the temperature on the storage and loss modulus of GFRP material acquired from the Fiberline Bridge was studied by the dynamic mechanical analysis. The good thermal stability in potential real temperatures was found. The natural vibration frequencies and mode shapes of the bridge for its original state were evaluated through the application of the Finite Element (FE) method. The initial FE model was created using the real geometrical and material data obtained from both the design data and flexural test results performed in 1997 for the intact composite GFRP material. Full scale experimental investigations of the free-decay response under human jumping for the experimental state were carried out applying accelerometers. Seven natural frequencies, corresponding mode shapes and damping ratios were identified. The numerical and experimental results were compared. Based on the difference in the fundamental natural frequency it was again confirmed that the structural stiffness of the bridge increased by about 9% after 20 years of service life. Data collected from this study were used to validate the assumed FE model. It can be concluded that the updated FE model accurately reproduces the dynamic behavior of the bridge and can be used as a proper baseline model for the long-term monitoring to evaluate the overall structural response under service loads. The obtained results provided a relevant data for the structural health monitoring of all-GFRP bridge.