• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.5
• /
• pp.28-33
• /
• 2004

Generally Horn-type rudders have been used for single propeller and single rudder system. The reason is that the rudder torques of Horn-type rudder are smaller than those of Spade rudder with same lift force. But it is found that the rudder cavitation occurs on a Horn-type rudder of fast container ship. In this paper the comparison results of Horn-type and Spade rudders are described. HPMM tests are carried out to compare the effects of two rudder types on the maneuverability of a ship. It is shown that the maneuvering performance of a ship equipped with Horn-type rudder is better than that equipped with Spade rudder by comparing the test results and maneuvering coefficients at scantling condition. The reason is that the movable part area of Horn-type rudder is about 14％ larger than that of Spade rudder with same total area. And the rudder torque of Spade rudder is greater than that of Horn rudder. At ballast condition, however, the effect of rudder type is negligible.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.1
• /
• pp.29-42
• /
• 1992

A potential based panel method is used to predict the open water characteristics of spade-type rudders. The inflow velocity is assumed to be constant in lime and uniform in space. Source and dipole are distributed on the rudder surface. It is assumed that the wake surface is streaming from trailing edge and it is represented by dipole distribution. In this paper, wake geometry is assumed by imposing appropriate conditions at the trailing edge and far from the body. The effects of wake geometry are studied. The pressure Kutta condition is applied at the trailing edge, the effects of which are compared with those of two-dimensional Kutta condition. The results of calculations for a spade-type rudder are compared with published results. It is concluded that this approach shows fairly good agreement with experimental results and can be used in the initial design stage of a rudder.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.42-46
• /
• 2013

Recently, according to the growth of demand about large container carrier, the studies for cavitation of semi-spade rudder were increased. In spite of many effort to solve, the fundamental solution can not be found. So, the studies for full-spade rudder are increasing to solve. In Pusan national university, the studies for full-spade twisted rudder and full-spade wavy twist rudder were carried out. However, most studies are carried out in numerical analysis and the many studies of experimental comparison between each rudder are not exist. This paper describe design history of full-spade rudder (twist rudder, wavy twist rudder) for KCS (KRISO Container Ship) and compare performance of each designed full-spade rudder about resistance and self-propulsion with conventional rudder (semi-spde rudder). The measurement about designed rudder's rudder force will be performed near future.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.1
• /
• pp.25-32
• /
• 2013

The shape of a conventional full spade rudder has been modified to implement the Coanda effect and consequential changes in the flow characteristics are carefully examined to show the significant enhancement in the lift performance. A preliminary numerical study has been done to identify the optimum configuration of the modified rudder sections. For the purpose, chord wise locations of the jet slit and the radii of the trailing edge were varied in several ways and the changes in the lift characteristics have been observed at the various angles of attack, particularly focusing on the usefulness of the Coanda effect upon delaying the stall or increase in the circulation. Making the most use of the results so attained, full spade rudder of a VLCC has been reformed to realize the Coanda effect. A series of model experiments and numerical simulations are performed to confirm the effectiveness of the Coanda effect in improving the performance of the modified rudder. It is found that considerable enhancement in the lift performance of the rudder is plausible at any rudder angle if an optimum jet momentum is provided.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.163-177
• /
• 2010

This article examines hydrodynamic characteristics and speed performances of a ship attached with a full spade and a twisted rudder based on a computational method. For this study, a 13,100 TEU container carrier is selected. The turbulent flows around a ship are analyzed by solving the Reynolds-averaged Navier-Stokes equation together with the application of Reynolds stress turbulence model. The computations are carried out at the conditions of rudder, bare hull, hull-rudder and hull-propeller-rudder. An asymmetric body-force propeller is applied. The speed performance is predicted by the model-ship performance analysis method of the revised ITTC'78 method. The hydrodynamic forces are compared in both rudder-open-water and self-propulsion conditions. The flow characteristics, the speed performance including propulsion factors and the rudder-cavitation performance are also compared. The model tests are conducted at a deep-water towing tank to validate the computational predictions. The computational predictions show that the twisted rudder is superior to the full spade rudder in the respect of the speed and the cavitation performances.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.4 s.148
• /
• pp.422-430
• /
• 2006

The horn and movable parts around the gap of the conventional semi-spade rudder are visualized by high speed CCD camera with the frame rate of 4000 fps (frame per second) to study the unsteady cavity pattern on the rudder surface and gap. In addition, the pressure measurements are conducted on the rudder surface and inside the gap to find out the characteristics of the flow behavior. The rudder without propeller wake is tested at the range of $1.0{\leq}{\sigma}_v\;1.6$ and at the rudder deflection angle of $-8{\leq}{\theta}{\leq}10^{\circ}$. The time resolved cavity images are captured and show strong cavitation around the rudder gap in all deflection angles. As the deflection angle gets larger, the flow separated from the horn surface increases the strength of cavitation. The accelerated flow along the horn decreases its pressure and the separated flow from the horn increases the pressure abruptly. The pressure distribution inside the gap reveals the flow moving from the pressure to suction side. In the negative deflection angle, the turning area on the movable part initiates the flow separation and cavitation on it.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.578-585
• /
• 2006

Cavitation related erosion damages on semi-spade rudder generally occur at around leading edge of lower-face and behind gap of lower pintle. To get the idea of gap entrance profile for the latter case, a series of tests with large models has been carried out at MOERI. In the tests, the flow pattern around lower pintle have been investigated and visualized by high speed camera. Additionally, cavitation inception tests and pressure measurements have also been conducted for better comparison. As a result a new model (F rudder) has been developed. The new model turned out to have stable pressure distribution along the surface and so the cavitation inception speeds within ${\pm}5^{\circ}$ of rudder angle were delayed approx. 4 knots in average.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.5
• /
• pp.479-487
• /
• 2009

This paper describes the design of a full-spade twisted rudder section by using the genetic algorithm based on VLM(Vortex Lattice Method) and panel method. The developed propeller- rudder analysis program has been validated by comparing with experimental data. The developed code has been used for the design of a twisted full-spade rudder especially for finding out optimum section. The optimization has been firstly carried out by the genetic algorithm. The more detail variation of a rudder section has been also conducted by changing section profile in more detail to confirm the most optimum section profile. The developed new twisted rudder has been compared with existing twisted rudder by cavitation testing in the cavitation tunnel at MOERI. It is concluded that the developed twisted rudder has a lower cavity in comparison with existing twisted rudder. The verification of efficiency gain is expected to be carried out through self-propulsion tests in the near future.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.5
• /
• pp.324-333
• /
• 2013

Recently, rudder erosion due to cavitation has been frequently reported on a semi-spade rudder of a high-speed large ship. This problem raises economic and safety issues when operating ships. The semi-spade rudders have a gap between the horn/pintle and the movable wing part. Due to this gap, a discontinuous surface, cavitation phenomenon arises and results in unresolved problems such as rudder erosion. In this study, we made a rudder model for 2-D experiments using the NACA0020 and also manufactured gap flow blocking devices to insert to the gap of the model. In order to study the gap flow characteristics at various rudder deflection angles($5^{\circ}$, $10^{\circ}$, $35^{\circ}$) and the effect of the gap flow blocking devices, we carried out the velocity measurements using PIV(Particle Image Velocimetry) techniques and cavitation observation using high speed camera in Seoul National University cavitation tunnel. To observe the gap cavitation on a semi-spade rudder, we slowly lowered the inside pressure of the cavitation tunnel until cavitation occurred near the gap and then captured it using high-speed camera with the frame rate of 4300 fps(frame per second). During this procedure, cavitation numbers and the generated location were recorded, and these experimental data were compared with CFD results calculated by commercial code, Fluent. When we use gap flow blocking device to block the gap, it showed a different flow character compared with previous observation without the device. With the device blocking the gap, the flow velocity increases on the suction side, while it decreases on the pressure side. Therefore, we can conclude that the gap flow blocking device results in a high lift-force effect. And we can also observe that the cavitation inception is delayed.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.3
• /
• pp.238-246
• /
• 2008

In the present study, the influences on the gap cavitaiton of the semi-spade rudder are investigated experimentally in the condition with propeller and hull wakes. To reduce the scale effect in the given experimental conditions, 1/28.5-scale-down models of propeller and rudder are manufactured. We have the propeller rotate ahead of the rudder, inducing the three dimensional effects originated from the propeller action. Experimental methods are composed of the cavitation observation using high speed camera, PIV (particle image velocimetry) measurements to visualize the cavitaition and flows around the gap. The propeller slipstream affects both of the gap flows and cavitation of the rudder.